One path vs many paths

Series vs Parallel

The difference between series and parallel circuits is the number of paths for current: a series circuit connects components end to end in one loop, while a parallel circuit gives each component its own branch across the same voltage. In series the current is the same everywhere and the voltage is shared. In parallel the voltage is the same on every branch and the current is shared.

Two hand-built circuits with three bulbs each, dim bulbs wired in one loop beside bright bulbs wired on separate branches
The same three bulbs glow dimly when wired in series and brightly when each has its own parallel branch.

At a Glance

In a series circuit, resistances add, Rs = R1 + R2 + R3, the current is the same through every part, and one break stops everything. In a parallel circuit, 1/Rp = 1/R1 + 1/R2 + 1/R3, every branch gets the full supply voltage, and the total resistance is lower than the smallest branch.

Series
One path; same current everywhere
Parallel
Several branches; same voltage on each
Total resistance
Series: Rs = R1 + R2 + … · Parallel: 1/Rp = 1/R1 + 1/R2 + …
If one part fails
Series: all stop · Parallel: others keep working
Typical use
Series: switches, fuses · Parallel: home wiring
On this page
  1. What Is the Difference Between Series and Parallel Circuits?
  2. How Are Series and Parallel Circuits Defined?
  3. How Do Current and Voltage Behave in Series and Parallel?
  4. How Do You Calculate Total Resistance in Series and Parallel?
  5. What Changes When the Same Resistors Are Rewired?
  6. What Are the Advantages and Disadvantages of Each?
  7. What Are Real-Life Examples of Series and Parallel Circuits?
  8. Practice Series and Parallel Circuit Problems
  9. Common Misconceptions
  10. Key Facts
  11. Quiz
  12. FAQ

What Is the Difference Between Series and Parallel Circuits?

Picture two ways of wiring three bulbs to a battery. In the first, the wire runs from the battery to bulb one, then to bulb two, then to bulb three and back, like beads on a single string. That is a series circuit. In the second, each bulb is wired directly across the battery on its own branch, like the rungs of a ladder. That is a parallel circuit.

The wiring pattern decides almost everything about how the circuit behaves: how bright the bulbs glow, how much current the battery supplies, and what happens when one bulb burns out. In series, the bulbs share the battery's voltage. In parallel, each bulb gets all of it.

The table below compares the two point by point. If the basic parts of a circuit are new to you, start with our electric circuit overview.

Series and parallel circuits compared side by side
FeatureSeries circuitParallel circuit
Number of current pathsOneTwo or more branches
CurrentSame through every componentSplits among branches, then recombines
VoltageShared among componentsSame across every branch
Total resistanceRs = R1 + R2 + R3 + …1/Rp = 1/R1 + 1/R2 + 1/R3 + …
Total compared with partsLarger than the largest resistorSmaller than the smallest resistor
Adding another resistorTotal resistance rises, current fallsTotal resistance falls, current rises
Adding another bulbAll bulbs get dimmerOther bulbs keep the same brightness
If one component breaksWhole circuit stopsOther branches keep working
Independent switchingNot possibleEach branch can have its own switch
Hottest resistorThe largest resistanceThe smallest resistance
Wiring neededLeastMore
Typical usesSwitches, fuses, cells stacked for higher voltageHousehold outlets and lights, car lamps
Source: Rules follow from Ohm's law and Kirchhoff's junction and loop rules · Retrieved October 2026

How Are Series and Parallel Circuits Defined?

In a series circuit, components are joined end to end so that there is exactly one path around the loop. Every electron that leaves the battery must pass through every component before it returns. There are no junctions where the current can split.

In a parallel circuit, the components connect between the same two points, called nodes. The current reaches a junction, divides among the branches, and recombines at the far node. Each branch forms its own complete loop with the battery.

Many real circuits mix both patterns. A light switch, for example, sits in series with the lamp it controls, while all the lamps in a house sit in parallel with each other.

How Do Current and Voltage Behave in Series and Parallel?

In series, the current is the same at every point, because charge has nowhere else to go. The voltage is shared: each resistor takes a slice of the supply in proportion to its resistance, and the slices add up to the battery voltage. A larger resistor in series takes a larger share.

In parallel, the voltage is the same across every branch, because each branch connects to the same two nodes. The current is shared: each branch draws I=V/R on its own, so a smaller resistance draws more current, and the branch currents add up to the total from the battery.

These two rules are really Kirchhoff's laws in action: charge is conserved at every junction, and voltages around any closed loop add to zero. The diagram below shows a parallel circuit with three branches across a 12 V battery.

Example 3 Current in one parallel branch

A 20 Ω resistor sits on one branch of a parallel circuit powered by a 12 V battery. Because it is connected directly across the battery, it has the full 12 V across it. What current flows through that branch?

  1. Given:
    • voltage across the resistor: V=12 V
    • resistance: R=20 Ω
  2. Formula: I=VR
  3. Substitute: I=(12 V)(20 Ω)
  4. Answer: I=0.6 A

Each branch can be handled with Ohm's law on its own, then the branch currents add up to the total drawn from the battery.

Parallel circuit schematic: 12 V battery and switch feeding three branches of 10, 20 and 30 ohms, each with the full 12 V across it
Each branch has the full 12 V across it, so the 10 Ω branch draws the most current and the 30 Ω branch the least.

How Do You Calculate Total Resistance in Series and Parallel?

For resistors in series, simply add them: Rs=R1+R2+R3+⋯. Each extra resistor is one more obstacle in the only path, so the total always grows.

For resistors in parallel, add the reciprocals: 1Rp=1R1+1R2+1R3+⋯, then take the reciprocal of the sum. For just two resistors there is a handy shortcut, Rp=R1R2R1+R2. The total is always less than the smallest branch, because each branch adds a new path.

Once you have the total resistance, Ohm's law gives the total current. The full derivations are on the resistors in series and parallel page, and our series and parallel resistor calculator handles any combination.

Here is the formula for the total resistance of resistors in series, with each variable and its SI unit. The parallel rule follows in the text.

Rs=R1+R2+R3+⋯
What each symbol means
SymbolQuantitySI unit
Rsequivalent series resistanceohm (Ω)
R1resistance 1ohm (Ω)
R2resistance 2ohm (Ω)
R3resistance 3ohm (Ω)

Valid for: same current through each resistor.

Example 1 Three resistors in a row

A student connects resistors of 47 Ω, 68 Ω and 100 Ω end to end in a single loop. What is the total resistance of the series combination?

  1. Given:
    • resistance 1: R1=47 Ω
    • resistance 2: R2=68 Ω
    • resistance 3: R3=100 Ω
  2. Formula: Rs=R1+R2+R3+⋯
  3. Substitute: R1=47 Ω,R2=68 Ω,R3=100 Ω
  4. Answer: Rs=215 Ω

The total is larger than any single resistor, because the current has to push through all three one after another.

Example 2 The same resistors side by side

The student now connects the same 47 Ω, 68 Ω and 100 Ω resistors in parallel, each across the same two points. What is the total resistance of the parallel combination?

  1. Given:
    • resistance 1: R1=47 Ω
    • resistance 2: R2=68 Ω
    • resistance 3: R3=100 Ω
  2. Formula: 1Rp=1R1+1R2+1R3+⋯
  3. Substitute: R1=47 Ω,R2=68 Ω,R3=100 Ω
  4. Answer: Rp=21.75 Ω

The total is smaller than the smallest resistor, because every added branch gives the current another way through.

What Changes When the Same Resistors Are Rewired?

Take three resistors of 10 Ω, 20 Ω and 30 Ω and a 12 V battery. The table below shows what happens when you wire them first in series and then in parallel. Every number in it comes straight from V=IR and P=IV.

In series, the total resistance is high, so only a small current flows, and the battery delivers just a few watts. In parallel, the total resistance drops below the smallest resistor, the current is eleven times larger, and the power drawn from the battery rises by the same factor.

Notice also where the power goes. In series the largest resistor runs hottest, because it takes the biggest share of the voltage. In parallel the smallest resistor runs hottest, because it draws the most current.

10 Ω, 20 Ω and 30 Ω resistors on a 12 V battery, wired in series and in parallel
QuantitySeriesParallel
Total resistance60 Ω5.45 Ω
Total current from battery0.20 A2.20 A
Voltage across 10 Ω2.0 V12 V
Voltage across 20 Ω4.0 V12 V
Voltage across 30 Ω6.0 V12 V
Current through 10 Ω0.20 A1.20 A
Current through 20 Ω0.20 A0.60 A
Current through 30 Ω0.20 A0.40 A
Power in 10 Ω0.40 W14.4 W
Power in 30 Ω1.20 W4.8 W
Total power from battery2.4 W26.4 W
Source: Computed with Rs = R1 + R2 + R3, 1/Rp = 1/R1 + 1/R2 + 1/R3, V = I R and P = I V · ideal battery and wires · Retrieved October 2026

What Are the Advantages and Disadvantages of Each?

Series circuits are simple, use the least wire, and are perfect when you want one device to control the whole loop. A fuse or circuit breaker must be in series so that it can cut off everything downstream; see fuses and circuit breakers. The drawback is that a single break stops all current, and adding devices dims every one of them.

Parallel circuits let each device run at full voltage and be switched on or off independently. If one bulb fails, the others stay lit. The drawback is that every added branch draws more total current, which can overload a supply. A wire with almost no resistance placed across a branch creates a short circuit, a very large current that protective devices are designed to stop.

What Are Real-Life Examples of Series and Parallel Circuits?

Series connections appear wherever one part must control or protect the rest:

  • A wall switch and the ceiling light it operates.
  • Batteries stacked end to end in a flashlight to add their voltages.
  • Some older strings of decorative lights, where one dead bulb darkened the whole strand.

Parallel connections appear wherever devices must work independently:

  • Outlets and lights in a home, which all receive the same mains voltage.
  • Car headlights, so one failed lamp does not leave the driver in the dark.
  • The cells in many laptop and electric car battery packs, grouped to share the load current.

You can test both patterns yourself with our series and parallel circuits lab, or build them virtually in the circuit simulator.

Practice Series and Parallel Circuit Problems

Solving the same set of resistors both ways is the fastest route to mastery. Our series and parallel circuits worksheets include printable answer keys, and the quiz below checks the key ideas. The junction and loop rules used on this page are named after Gustav Kirchhoff, and the link between voltage, current and resistance after Georg Ohm.

Common Misconceptions

Myth: Current gets used up as it flows through each bulb in a series circuit.

Physics: The current is the same at every point in a series loop. Energy is transferred in each bulb, but the charge itself is not consumed.

Myth: Adding more resistors always increases the total resistance.

Physics: Only in series. Adding a resistor in parallel opens another path, so the total resistance goes down.

Myth: Each branch of a parallel circuit gets a fraction of the battery voltage.

Physics: Every parallel branch has the full battery voltage across it. It is the current, not the voltage, that is divided among the branches.

Myth: Parallel circuits use less power because the current is split.

Physics: The opposite is usually true. Parallel wiring lowers the total resistance, so the battery supplies more total current and more power.

Key Facts

  • A series circuit has one path for current, while a parallel circuit has two or more branches.
  • In series the current is the same everywhere; in parallel the voltage is the same across every branch.
  • Series resistances add directly: Rs = R1 + R2 + R3.
  • Parallel resistances add as reciprocals, 1/Rp = 1/R1 + 1/R2 + 1/R3, so the total is below the smallest branch.
  • A break anywhere in a series circuit stops all current, while a break in one parallel branch leaves the others working.
  • Homes are wired in parallel so every outlet gets the full mains voltage and devices switch on and off independently.
  • Fuses and switches are placed in series with the parts they protect or control.
Did you know? Adding a resistor in parallel always lowers the total resistance, even if the new resistor is enormous; a 1,000,000 Ω branch beside a 10 Ω resistor still nudges the total slightly below 10 Ω.

Quick Quiz: How Well Do You Know Series vs Parallel?

6 questions. Tap an answer to check it.

  1. In a series circuit, which quantity is the same through every component?

  2. In a parallel circuit, which quantity is the same across every branch?

  3. What is the total resistance of 5 Ω, 10 Ω and 15 Ω in series?

  4. Two 12 Ω resistors are connected in parallel. What is the total resistance?

  5. What happens to the total resistance when another resistor is added in parallel?

  6. Why is a fuse placed in series with the circuit it protects?

Frequently Asked Questions

What is the difference between series and parallel circuits?

A series circuit connects components one after another in a single loop, so the same current passes through each and the supply voltage is shared among them. A parallel circuit connects each component on its own branch between the same two points, so every branch gets the full voltage and the current divides. A break in series stops everything; a break in one parallel branch does not.

Is current the same in series or parallel?

Current is the same everywhere in a series circuit, because there is only one path for charge to follow. In a parallel circuit the current splits at each junction, and each branch carries a current set by its own resistance. The branch currents add up to the total current drawn from the source.

Is voltage the same in series or parallel?

Voltage is the same across every branch of a parallel circuit, because each branch connects to the same two points. In a series circuit the supply voltage is divided among the components, with larger resistances taking larger shares, and the individual voltages add up to the supply voltage.

Why are houses wired in parallel?

Parallel wiring gives every outlet and light the full mains voltage, so appliances work at their rated power. It also lets you switch each device on or off without affecting the others, and a failed lamp does not cut power to the rest of the house. Each circuit is still protected by a breaker placed in series with it.

Are bulbs brighter in series or parallel?

Identical bulbs are brighter in parallel. In parallel, each bulb has the full battery voltage across it, so it draws its full current and power. In series, the bulbs share the voltage, so each gets only a fraction of it and glows more dimly. The trade-off is that parallel bulbs drain the battery faster.

How do you calculate total resistance in parallel?

Add the reciprocals of the branch resistances and then take the reciprocal of the result: 1/Rp = 1/R1 + 1/R2 + 1/R3. For two resistors, Rp = R1 R2 / (R1 + R2). For example, two 40 Ω resistors in parallel give 20 Ω. The answer is always smaller than the smallest single resistor.

What happens if one bulb breaks in a series circuit?

All the bulbs go out. A broken filament leaves a gap in the only path, so no current can flow anywhere in the loop. That is why troubleshooting old series light strings meant testing bulbs one by one. In a parallel circuit, the broken bulb's branch stops working but the others stay lit.

Can a circuit be both series and parallel?

Yes. Most real circuits combine both, and they are called series-parallel or combination circuits. You solve them by simplifying step by step: replace each group of parallel resistors with its equivalent, then add any series resistances, and repeat until one total resistance remains. Ohm's law then gives the currents and voltages.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.