
At a Glance
An electric circuit is a complete, closed path that lets charge flow from a source of voltage through a load and back again. The current in a simple circuit follows Ohm's law, V = I R, so a 9 V battery driving a 30 Ω resistor pushes a current of 0.3 A.
- Basic parts
- Source, conductors, load (plus usually a switch)
- Must be
- A closed, unbroken loop
- Key formula
- V = IR (Ohm's law)
- Units
- Volts (V), amperes (A), ohms (Ω), watts (W)
- Main types
- Series, parallel and combination circuits
- Current kinds
- Direct current (DC) or alternating current (AC)
On this page
- What Is an Electric Circuit?
- Electric Circuits Explained Simply
- What Are the Parts of an Electric Circuit?
- What Is the Difference Between an Open and a Closed Circuit?
- How Are Voltage, Current and Resistance Related in a Circuit?
- What Are Series and Parallel Circuits?
- How Does a Circuit Deliver Energy?
- What Is the Difference Between DC and AC Circuits?
- Where Do You See Electric Circuits in Everyday Life?
- Going Deeper: Kirchhoff's Rules
- Practice and Build Your Own Circuits
- Common Misconceptions
- Key Facts
- Quiz
- FAQ
What Is an Electric Circuit?
A circuit is a path that starts and ends at the same place. In electricity, that path is made of conducting material, and charge travels around it again and again. The source gives the charge energy, the devices along the way use that energy, and the charge returns to the source to pick up more.
The flow of charge around the loop is the electric current. It only exists while the loop is complete. A single gap, whether from an open switch, a blown fuse or a broken wire, stops the current everywhere in that loop at once.
Circuits range from a battery and a bulb on a classroom bench to the billions of microscopic paths inside a phone processor. The same rules apply to all of them.
Electric Circuits Explained Simply
Think of a circuit as a loop of pipe filled with water, with a pump somewhere in the loop. The pump is the battery: it pushes the water around. The pipe is the wire. A water wheel in the loop is the light bulb: the moving water turns it and loses some energy doing so. A valve is the switch.
Close the valve and the water stops everywhere, not just at the valve. Open it and the flow starts all around the loop at once. Notice also that the pump does not create water; it just pushes the water that is already there. A battery does the same with the electrons already in the wires.
What Are the Parts of an Electric Circuit?
Nearly every circuit is built from the same handful of parts:
- Source: a battery, solar cell or generator that provides a voltage, the energy given to each coulomb of charge. See how batteries work.
- Conductors: wires or metal tracks with very low resistance that carry charge between parts. They work because metals are good conductors.
- Load: the device that uses the energy, such as a bulb, motor, heater or speaker. Loads are often modeled as a resistor.
- Switch: a gap you can open or close to stop or start the current.
- Protection: a fuse or circuit breaker that opens the loop if the current grows dangerously large.
Engineers draw circuits with standard symbols instead of pictures. Our guide to circuit diagram symbols shows each one.
What Is the Difference Between an Open and a Closed Circuit?
A closed circuit is a complete loop, so current flows and the devices work. An open circuit has a break somewhere, so no current flows and nothing works, even though the battery still has its voltage. Flipping a light switch simply opens or closes a gap in the loop.
A third case is the short circuit, where current finds a path with almost no resistance and bypasses the load. Because nothing limits it, the current can become huge, heating the wires and draining or damaging the source. Fuses and breakers exist to stop this. For the deeper reason a loop must be closed, read why a circuit needs to be closed.
How Are Voltage, Current and Resistance Related in a Circuit?
Three quantities describe what happens in a circuit. Voltage (V, in volts) is the push the source gives each unit of charge. Current (I, in amperes) is how much charge flows past a point each second. Resistance (R, in ohms) is how strongly the load opposes the flow.
For many loads they are linked by Ohm's law,
To solve any of the three quickly, use the Ohm's law calculator.
Ohm's law ties together the three quantities that describe any simple circuit: the push from the source, the flow of charge and the opposition of the load.
| Symbol | Quantity | SI unit |
|---|---|---|
| voltage across the resistor | volt (V) | |
| current | ampere (A) | |
| resistance | ohm (Ω) |
Rearranged to find another variable:
Valid for: ohmic conductors (R independent of V and I).
Example 1 Current through a flashlight bulb
A flashlight runs on a 4.5 V battery pack, and its bulb has a resistance of 15 Ω while lit. What current flows around the circuit?
- Given:
- voltage across the resistor:
- resistance:
- voltage across the resistor:
- Formula:
- Substitute:
- Answer:
The same current passes through every part of this single loop: the batteries, the switch, the bulb and the wires.
Example 2 Finding the resistance of a heater coil
A small 12 V heater for a car seat draws a current of 4 A. What is the resistance of its heating element?
- Given:
- voltage across the resistor:
- current:
- voltage across the resistor:
- Formula:
- Substitute:
- Answer:
A low resistance lets a large current through, which is exactly what a heater needs to produce warmth.
What Are Series and Parallel Circuits?
When a circuit has more than one load, the parts can be connected in two basic ways. In a series circuit, the loads sit one after another on a single path, so the same current passes through each. If one bulb burns out, the loop opens and every bulb goes dark.
In a parallel circuit, each load has its own branch connected across the source, so each gets the full source voltage. If one branch fails, the others keep working, which is why homes are wired in parallel. Many real circuits combine both arrangements.
The two diagrams below use the same 9 V battery and the same pair of resistors, 30 Ω and 60 Ω. In series they share the voltage and carry one small current; in parallel each branch draws its own current from the full 9 V. Our series vs parallel circuits page compares the two in detail.


How Does a Circuit Deliver Energy?
A circuit is really an energy delivery system. The source converts some other form of energy, chemical in a battery or mechanical in a generator, into electrical energy carried by the charges. The load converts it again, into light, heat, motion or sound.
The rate of delivery is the electric power,
The charges themselves are not used up. The same electrons circulate, and only their energy is handed over, just as the water in a heating loop keeps circulating while it gives off warmth.
Example 3 Power used by a desk fan
A desk fan plugged into a 120 V outlet draws a current of 0.25 A. How much power does the circuit deliver to the fan?
- Given:
- current:
- voltage:
- current:
- Formula:
- Substitute:
- Answer:
Power tells you how fast the circuit hands energy to the device, here a modest rate typical of a small fan.
| Device | Typical power (W) | Current (A) | Effective resistance (Ω) |
|---|---|---|---|
| LED light bulb | 9 | 0.075 | 1,600 |
| Laptop charger | 65 | 0.54 | 222 |
| Television | 100 | 0.83 | 144 |
| Toaster | 900 | 7.5 | 16 |
| Microwave oven | 1,100 | 9.2 | 13 |
| Hair dryer | 1,500 | 12.5 | 9.6 |
| Source: Current computed with I = P / V and effective resistance with R = V² / P at 120 V; power ratings are typical values · Retrieved October 2026 | |||
What Is the Difference Between DC and AC Circuits?
In a direct current (DC) circuit, charge flows in one direction only. Batteries, solar panels and the circuits inside phones and laptops run on DC. In an alternating current (AC) circuit, the direction reverses many times per second, 60 times in North America and 50 in most other countries.
Wall outlets supply AC because it is easy to step up and down with transformers for long-distance transmission. Chargers convert it to DC for electronics. For a side-by-side look, see AC vs DC.
Where Do You See Electric Circuits in Everyday Life?
A flashlight is about the simplest real circuit: batteries, a switch, a bulb or LED and a metal strip that closes the loop. A string of holiday lights may be wired in series, so one loose bulb can darken a whole section. The outlets in a kitchen are wired in parallel, each on its own branch, so the toaster works whether or not the kettle is on.
A car contains dozens of circuits fed by one 12 V battery, each with its own fuse. Your own nervous system runs on electrical signals too, as described in electricity in the body. Every one of these follows the same rule: no closed loop, no current.

Going Deeper: Kirchhoff's Rules
For complex circuits with many loops and branches, Ohm's law alone is not enough. Physicists use two bookkeeping rules known as Kirchhoff's laws. The junction rule says the current flowing into any junction equals the current flowing out, because charge cannot pile up. The loop rule says the voltage gains and drops around any closed loop add to zero, because energy is conserved.
Together with Ohm's law, these two rules can solve any circuit made of batteries and resistors, however tangled. Circuit simulation software uses exactly this approach.
Practice and Build Your Own Circuits
Practice drawing and reading schematics with our circuit diagram worksheets, which come with answer keys. Then experiment safely on screen with the circuit builder, where you can connect batteries, bulbs and resistors in series or parallel and watch the currents change. All the circuit relations are gathered on the electricity formula sheet, and Georg Ohm's page tells the story behind V = IR.
Common Misconceptions
Myth: A battery stores electrons and pumps them out into the circuit until they run out.
Physics: A battery supplies energy, not charge. The electrons were already in the wires; the battery pushes them around the loop.
Myth: Current gets used up as it passes through a bulb, so less comes out than goes in.
Physics: Current is the same on both sides of a bulb in a single loop. The bulb takes energy from the charges, not the charges themselves.
Myth: Only one wire is needed to connect a battery to a bulb.
Physics: The charge must return to the source, so the circuit needs a complete loop from one terminal, through the bulb, to the other terminal.
Myth: Electrons travel from the battery to the bulb at nearly the speed of light.
Physics: The signal travels fast, but the electrons themselves drift slowly. The bulb lights quickly because electrons all along the wire start moving together.
Key Facts
- An electric circuit is a closed loop that lets current flow from a source, through a load and back.
- Every circuit needs a source of voltage, conducting paths and a load that uses the energy.
- An open circuit has a break, so no current flows; a closed circuit is complete.
- In a simple circuit, voltage, current and resistance are linked by Ohm's law, V = IR.
- Series circuits have one path and the same current everywhere; parallel circuits give each branch the full source voltage.
- A circuit delivers energy at a rate given by P = IV, measured in watts.
- Charges are not used up in a circuit; only the energy they carry is transferred to the load.
Quick Quiz: How Well Do You Know What Is an Electric Circuit??
6 questions. Tap an answer to check it.
What must be true for current to flow in a circuit?
Current only flows around a complete, unbroken loop.
In a series circuit with three bulbs, one bulb burns out. What happens?
A series circuit has one path, so a break anywhere stops the current through every bulb.
A 6 V battery drives a current through a 3 Ω resistor. What is the current?
I = V/R = 6 V / 3 Ω = 2 A.
Why are homes wired in parallel?
Each branch is connected across the supply, so devices run at full voltage and do not depend on each other.
What does a battery supply to a circuit?
A battery gives energy to charges already in the circuit; the charges are not consumed.
Which device protects a circuit from too much current?
A fuse melts and opens the loop when the current gets too large.
Frequently Asked Questions
What is an electric circuit in simple words?
An electric circuit is a closed loop that electricity can travel around. It starts at a source such as a battery, runs through wires to a device such as a bulb or motor, and comes back to the source. If the loop is complete, current flows and the device works. If the loop is broken anywhere, everything in that loop stops.
What are the three basic parts of a circuit?
The three essential parts are a source of energy, a conducting path and a load. The source, usually a battery or the power grid, provides the voltage. The conducting path, usually copper wire, carries charge between parts. The load, such as a lamp or heater, turns the electrical energy into something useful. Most circuits also include a switch to control the current.
What are the types of electric circuits?
Circuits are usually grouped by how their parts are connected. A series circuit has a single path for current. A parallel circuit has several branches, each connected across the source. A combination circuit mixes both. Circuits can also be described as open, closed or short, and as direct current or alternating current depending on how the charge flows.
Why does a circuit need to be closed?
Current is a continuous flow of charge, and charge cannot pile up endlessly at a dead end. In a broken loop, a little charge builds up at the gap and then pushes back, stopping the flow almost instantly. Only a complete loop lets charge keep circulating from the source, through the load and back again, so energy can be delivered steadily.
What is the difference between a series and a parallel circuit?
In a series circuit every part is on one path, so the same current flows through all of them and the source voltage is shared. If one part fails, the whole circuit stops. In a parallel circuit each part is on its own branch with the full source voltage, so the branches work independently. Homes are wired in parallel for that reason.
What is a short circuit?
A short circuit happens when current finds an unintended path with very little resistance, skipping the normal load. With almost nothing to limit it, the current can become very large, overheating wires, damaging the source and sometimes starting fires. Fuses and circuit breakers detect the excess current and open the circuit before serious damage occurs.
How does a switch work in a circuit?
A switch is a controlled gap in the loop. When it is closed, two metal contacts touch and current can pass. When it is open, the contacts separate, leaving an air gap that acts as an insulator, so the current stops everywhere in that loop. Light switches, push buttons and the transistors inside computers all perform this same job.
What is the difference between an electric circuit and electric current?
The circuit is the path, and the current is the flow along it. A circuit is the physical loop of source, wires and devices. Current is the rate at which charge moves through that loop, measured in amperes. You can have a circuit with no current, such as one with an open switch, but you cannot have a steady current without a circuit.








