Voltage, current and resistance

Ohm's Law (V = IR)

Ohm's law states that the current through a conductor is proportional to the voltage across it, as long as its temperature and other conditions stay the same. Written as V = IR, it links voltage in volts, current in amperes and resistance in ohms, so knowing any two of them gives you the third.

Breadboard circuit with resistors, jumper wires and a lit LED, with multimeter probes measuring across a resistor
Measuring the voltage across a resistor and the current through it is the everyday way to put Ohm's law to work.

At a Glance

Ohm's law says voltage equals current times resistance: V = I × R. Voltage is in volts (V), current in amperes (A) and resistance in ohms (Ω), so I = V / R and R = V / I. It holds for ohmic conductors such as metal wires and ordinary resistors kept at a steady temperature.

Discovered by
Georg Simon Ohm
Published
1827, in Die galvanische Kette, mathematisch bearbeitet
Formula
V = IR (also I = V/R and R = V/I)
SI units
volt (V), ampere (A), ohm (Ω)
Quantities
All three are scalars; current has a direction along the wire
Applies to
Ohmic conductors (metal wires, resistors) at constant temperature
On this page
  1. What Does Ohm's Law Say?
  2. Ohm's Law Explained Simply
  3. What Is the Formula for Ohm's Law?
  4. How Do You Use the Ohm's Law Triangle?
  5. How Do You Test Ohm's Law in a Circuit?
  6. Which Materials Obey Ohm's Law?
  7. Where Is Ohm's Law Used in Real Life?
  8. Who Discovered Ohm's Law?
  9. Going Deeper: When Does Ohm's Law Fail?
  10. Practice Ohm's Law Problems
  11. Common Misconceptions
  12. Key Facts
  13. Quiz
  14. FAQ

What Does Ohm's Law Say?

Ohm's law describes how three basic quantities in a circuit depend on one another. The voltage across a component is the push that drives charge through it. The current is how much charge flows past a point each second. The resistance is how strongly the component holds that flow back.

The law says that for many materials, current rises in step with voltage. Double the voltage across a resistor and the current doubles. Triple it and the current triples. The fixed ratio between them is the resistance, so R=V/I stays the same no matter which voltage you choose.

Strictly speaking, that steady ratio is the actual law. The equation V=IR on its own just defines resistance for any component at any moment. Ohm's discovery was that for metal wires and similar conductors, the resistance does not change as the voltage changes, provided the temperature stays fixed.

Ohm's Law Explained Simply

Picture water flowing through a garden hose. The water pressure from the tap plays the part of voltage, the amount of water coming out each second plays the part of current, and a narrow nozzle plays the part of resistance. Turn the tap up and more water flows. Squeeze the nozzle tighter and less water flows for the same pressure.

Electric circuits behave the same way. A bigger battery voltage pushes more current through the same bulb. A bulb with more resistance lets less current through from the same battery. That is all Ohm's law says: current equals voltage divided by resistance.

The analogy has limits, since electrons are not water and wires are not pipes. Still, it gives the right instinct for most everyday circuits, and it is a good way to check whether an answer makes sense.

What Is the Formula for Ohm's Law?

Ohm's law is written V=IR. Here V is the voltage in volts, I is the current in amperes and R is the resistance in ohms. Solve for current with I=V/R and for resistance with R=V/I.

The units fit together exactly. One ohm is the resistance that lets one ampere flow when one volt is applied, so 1 Ω=1 V/A. Keep voltage in volts and current in amperes, not milliamperes, and the resistance comes out in ohms with no extra factors.

For quick answers with unit conversions and every step shown, use our Ohm's law calculator. The first worked example below solves a household problem by hand.

Here is Ohm's law with each symbol and its SI unit, plus the two rearranged forms for finding current or resistance.

V=IR
What each symbol means
SymbolQuantitySI unit
Vvoltage across the resistorvolt (V)
Icurrentampere (A)
Rresistanceohm (Ω)

Rearranged to find another variable:

I=VRR=VI

Valid for: ohmic conductors (R independent of V and I).

Example 1 Current through a toaster element

The heating element of a toaster has a resistance of 16 Ω when hot and is plugged into a 120 V outlet. How much current flows through it?

  1. Given:
    • voltage across the resistor: V=120 V
    • resistance: R=16 Ω
  2. Formula: I=VR
  3. Substitute: I=(120 V)(16 Ω)
  4. Answer: I=7.5 A

That is a sizable current, which is why a toaster and a kettle on the same kitchen circuit can trip a breaker.

How Do You Use the Ohm's Law Triangle?

Many students remember the three forms of the law with a triangle. Write V at the top, and I and R side by side along the bottom. Cover the quantity you want to find with your finger, and what is left shows how to calculate it.

  • Cover V: I and R sit next to each other, so multiply: V=I×R.
  • Cover I: V sits above R, so divide: I=V/R.
  • Cover R: V sits above I, so divide: R=V/I.

The triangle is a memory aid, not new physics. Once the algebra feels natural, you can rearrange V=IR directly. Either way, always write the units next to each number, because mixing milliamperes and amperes is the most common source of answers that are off by a factor of a thousand.

Example 2 Voltage across a sensor resistor

A current of 0.025 A flows through a 330 Ω resistor in a hobby circuit. What voltage does a meter read across the resistor?

  1. Given:
    • current: I=0.025 A
    • resistance: R=330 Ω
  2. Formula: V=IR
  3. Substitute: V=(0.025 A)(330 Ω)
  4. Answer: V=8.25 V

Reading the voltage across a known resistor is a common trick for measuring current without breaking the circuit.

How Do You Test Ohm's Law in a Circuit?

The classic test uses a simple series circuit: a variable power supply, a resistor, an ammeter in series to read current and a voltmeter connected across the resistor to read voltage. The diagram below shows the layout. You raise the supply voltage in steps and record a current for each one.

Plot voltage against current and an ohmic resistor gives a straight line through the origin. The slope of that line equals the resistance. Our V–I graph experiment walks through the full procedure with a printable data sheet.

The table below shows what you should expect from a 220 Ω resistor. Every voltage step produces a matching step in current, and the ratio V/I comes back to 220 Ω each time.

Example 3 Finding an unknown resistance

A student connects an unlabeled component to a 9 V battery and an ammeter reads 0.075 A. What is the resistance of the component?

  1. Given:
    • voltage across the resistor: V=9 V
    • current: I=0.075 A
  2. Formula: R=VI
  3. Substitute: R=(9 V)(0.075 A)
  4. Answer: R=120 Ω

Repeating the test at a few other voltages shows whether the component is ohmic: the ratio V/I should stay the same.

Current through a 220 Ω resistor at different voltages
Voltage (V)Current (mA)V ÷ I (Ω)
1.56.82220
3.013.64220
4.520.45220
6.027.27220
9.040.91220
12.054.55220
Source: Computed with I = V / R for an ideal ohmic resistor at constant temperature · Retrieved October 2026
Series circuit with a 9 V battery, a 220 ohm resistor, an ammeter in series and a voltmeter across the resistor
The ammeter sits in series to read current, while the voltmeter sits across the resistor to read voltage.

Which Materials Obey Ohm's Law?

A component that follows Ohm's law is called ohmic. Metal wires, carbon film resistors and many other everyday conductors are ohmic over a wide range, as long as they do not heat up much. Their V–I graph is a straight line.

Many useful parts are non-ohmic. A filament lamp gets hotter as the current rises, its resistance climbs, and its graph curves over. A diode lets current through easily one way and barely at all the other way. A thermistor's resistance drops sharply as it warms. You can read more on our page about ohmic and non-ohmic conductors.

For non-ohmic parts you can still divide V by I at a given moment, but the answer changes with the operating point. That is why Ohm's law is best thought of as a property of certain materials, not a universal rule of nature.

How common components behave under Ohm's law
ComponentOhmic?Shape of V–I graphWhy
Carbon film resistorYesStraight line through originResistance stays almost constant
Copper wire (cool)YesStraight line through originTemperature barely changes
Filament lampNoCurve that flattensFilament heats up, resistance rises
DiodeNoNear zero, then steep rise one wayConducts in one direction only
Thermistor (NTC)NoCurve that steepensResistance falls as it warms
Neon lampNoNo current, then sudden jumpGas must ionize before it conducts
Source: Qualitative behavior of typical components · Retrieved October 2026
Coiled heating element glowing orange in a dark room, a resistor that turns electric current into heat
A heating element is a resistor chosen so the outlet voltage drives just the right current through it.

Where Is Ohm's Law Used in Real Life?

Ohm's law sits behind almost every electrical design decision:

  • LED resistors. An LED needs a limited current, so hobbyists pick a series resistor with R=V/I using the leftover voltage and the target current.
  • Heating elements. Toasters, kettles and hair dryers use a wire with a chosen resistance so that the outlet voltage drives the right current.
  • Fuses and breakers. Knowing a circuit's resistance tells an electrician how much current it will draw, so the right fuse rating can be chosen.
  • Sensors. Thermostats, light sensors and strain gauges change resistance, and a circuit turns that change into a voltage reading.
  • Wire sizing. Long, thin cables have more resistance, so they waste more voltage as heat. Ohm's law tells installers how thick a cable must be.

Ohm's law also pairs with the power formula P=IV, which turns a current and a voltage into watts. Our page on volts vs amps vs watts shows how the three ideas fit together.

Resistor with red, red, brown and gold color bands that mark a resistance of 220 ohms with 5 percent tolerance
Color bands tell you a resistor's value in ohms, the R you plug into Ohm's law.

Who Discovered Ohm's Law?

The German physicist and schoolteacher Georg Simon Ohm carried out his key experiments in 1825 and 1826 and published the result in 1827 in a book whose title translates roughly as The Galvanic Circuit Investigated Mathematically. He measured how the current through wires of different lengths and thicknesses depended on the driving source.

Reliable batteries were still new at the time, and Ohm switched to a thermocouple, a junction of two metals held at different temperatures, to get a steadier source. His conclusions were met coldly at first. Within a couple of decades, though, his law had become a cornerstone of electrical science.

Ohm was not quite the first. The English scientist Henry Cavendish had found a similar relation in 1781, but he never published it. Today the SI unit of resistance, the ohm, carries Georg Ohm's name.

Going Deeper: When Does Ohm's Law Fail?

Temperature is the biggest limit. In most metals, resistance rises as they warm up, because the vibrating atoms scatter the moving electrons more often. A lamp filament can have more than ten times the resistance when glowing than when cold, so a single value of R cannot describe it across the whole range.

Semiconductors, gases and electrolytes often break the law outright. In a neon sign the gas barely conducts until the voltage is high enough to ionize it, and then the current jumps. Superconductors sit at the other extreme, with zero resistance below a critical temperature.

On a deeper level, Ohm's law comes from the average drift of electrons in a material. Its microscopic form, current density proportional to electric field, connects the circuit rule to the resistivity of the material, which is how engineers predict a wire's resistance from its length and cross-section.

Practice Ohm's Law Problems

The quickest way to get fluent is to work a mixed set of problems that ask for voltage, current and resistance in turn. Our Ohm's law worksheets include printable answer keys. Check each answer with the calculator, see how the ideas compare on our current vs voltage page, then try the quiz below.

Common Misconceptions

Myth: V = IR is true for every component.

Physics: You can always compute V/I, but only ohmic components keep the same value as the voltage changes. Lamps, diodes and thermistors do not.

Myth: Current gets used up as it flows through a resistor.

Physics: The same current enters and leaves a resistor. What drops across it is the voltage, as electrical energy turns into heat.

Myth: A higher resistance always means less power is used.

Physics: At a fixed voltage, more resistance means less current and less power. At a fixed current, more resistance means more power, since P = I²R.

Myth: Voltage flows through a circuit like current does.

Physics: Voltage is a difference in electric potential between two points. Current is what flows; voltage is measured across a component, not through it.

Key Facts

  • Ohm's law states that current through a conductor is proportional to the voltage across it at constant temperature.
  • The formula is V = IR, with voltage in volts, current in amperes and resistance in ohms.
  • One ohm equals one volt per ampere.
  • Doubling the voltage across an ohmic resistor doubles the current through it.
  • An ohmic component gives a straight V–I graph through the origin, and the slope equals its resistance.
  • Filament lamps, diodes and thermistors are non-ohmic because their resistance changes as they operate.
  • Georg Simon Ohm published the law in 1827.
Did you know? Georg Ohm could not rely on the shaky batteries of his day, so he powered his key experiments with a thermocouple, two metals joined and held at different temperatures, because it gave a far steadier voltage.

Quick Quiz: How Well Do You Know Ohm's Law?

6 questions. Tap an answer to check it.

  1. A 6 V battery is connected across a 3 Ω resistor. What current flows?

  2. If the voltage across an ohmic resistor doubles, what happens to the current?

  3. Which unit is equal to one ohm?

  4. What does the V–I graph of an ohmic resistor look like?

  5. Which component does NOT obey Ohm's law?

  6. In what year did Georg Ohm publish his law?

Frequently Asked Questions

What is Ohm's law in simple terms?

Ohm's law says the current through a conductor equals the voltage across it divided by its resistance. A stronger push from the battery drives more current, and a part with more resistance lets less current through. In symbols it is V = IR, where V is voltage in volts, I is current in amperes and R is resistance in ohms.

What are the three forms of Ohm's law?

The three forms are V = I × R to find voltage, I = V / R to find current and R = V / I to find resistance. They are the same equation rearranged. The Ohm's law triangle, with V on top and I and R along the bottom, is a common way to remember which quantity to multiply and which to divide.

What is the unit of resistance in Ohm's law?

Resistance is measured in ohms, written with the Greek letter omega, Ω. One ohm is the resistance that lets one ampere flow when one volt is applied, so one ohm equals one volt per ampere. Large resistances are often written in kilohms (kΩ, thousands of ohms) or megohms (MΩ, millions of ohms).

Why is Ohm's law important?

Ohm's law is the starting point for designing and checking almost any circuit. It tells engineers what resistor an LED needs, how much current a heater will draw, how thick a cable must be and what fuse protects a circuit. Combined with the power formula P = IV, it lets you predict heat, energy use and safety limits in electrical systems.

Does Ohm's law apply to a light bulb?

Only loosely. An old-style filament bulb gets much hotter as the current rises, and its resistance climbs with temperature. Its V–I graph curves instead of staying straight, so it is a non-ohmic component. At any single operating point you can still compute R = V/I, but the value is different when the bulb is dim and when it is fully lit.

How do you find current using Ohm's law?

Divide the voltage by the resistance: I = V / R. For example, a 9 V battery across a 450 Ω resistor drives a current of 9 divided by 450, which is 0.02 A or 20 mA. Make sure the voltage is in volts and the resistance in ohms, so that the answer comes out in amperes.

What is the difference between Ohm's law and the power formula?

Ohm's law, V = IR, links voltage, current and resistance. The power formula, P = IV, gives the rate at which electrical energy is transferred, in watts. Combining them gives two more useful forms, P = I²R and P = V²/R. Ohm's law tells you how much current flows, and the power formula tells you how much energy that current delivers each second.

Is Ohm's law always true?

No. It holds for ohmic conductors, such as metal wires and ordinary resistors, when their temperature stays steady. It fails for semiconductors like diodes and transistors, for gases in discharge tubes, for components that heat up a lot and for superconductors. For the resistors and wires in most everyday circuits, though, it is very accurate.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.