
At a Glance
Kirchhoff's current law (junction rule) says Σ I_in = Σ I_out at every junction, because charge is conserved. Kirchhoff's voltage law (loop rule) says Σ ΔV = 0 around any closed loop, because energy is conserved. Combined with Ohm's law, V = IR, they solve any circuit of batteries and resistors.
- Discovered by
- Gustav Kirchhoff
- Year
- 1845
- Current law (KCL)
- Σ Iin = Σ Iout at a junction
- Voltage law (KVL)
- Σ ΔV = 0 around a closed loop
- Based on
- Conservation of charge (KCL) and of energy (KVL)
- Applies to
- Steady (DC) circuits and slowly changing AC circuits
On this page
- What Are Kirchhoff's Laws?
- Kirchhoff's Laws Explained Simply
- What Is Kirchhoff's Current Law?
- What Is Kirchhoff's Voltage Law?
- How Do You Choose Signs in Kirchhoff's Laws?
- How Do You Solve a Circuit With Kirchhoff's Laws?
- Who Discovered Kirchhoff's Laws?
- Where Are Kirchhoff's Laws Used?
- Going Deeper: When Do Kirchhoff's Laws Break Down?
- Practice Kirchhoff's Law Problems
- Common Misconceptions
- Key Facts
- Quiz
- FAQ
What Are Kirchhoff's Laws?
Kirchhoff's laws are two bookkeeping rules that every steady electric circuit must obey. The first, the current law, tracks charge: whatever flows into a junction must flow out. The second, the voltage law, tracks energy: a charge that travels once around a closed loop ends up with the same electric potential it started with.
Neither law is a new force or effect. Both are conservation laws written in circuit language. That is why they work for any arrangement of batteries, resistors, bulbs and wires, however tangled it looks.
Simple circuits can be solved with the series and parallel rules alone. As soon as a circuit has two batteries in different branches, or a bridge that is neither series nor parallel, Kirchhoff's laws become the main tool.
Kirchhoff's Laws Explained Simply
Think of a set of water pipes. Where pipes meet, the water coming in each second must equal the water going out, because water cannot pile up or vanish at the joint. That is the current law.
Now think of hiking a mountain trail that ends where it started. You may climb and descend many times along the way, but when you finish the loop, your total change in height is zero. In a circuit, the battery is the climb and each resistor is a descent. That is the voltage law.
Put those two ideas together with Ohm's law, which says how much voltage each resistor uses for a given current, and you can predict every current and voltage in the circuit.
What Is Kirchhoff's Current Law?
Kirchhoff's current law, also called the junction rule or the first law, says the sum of the currents entering a junction equals the sum of the currents leaving it. A junction, or node, is any point where three or more wires meet.
The reason is conservation of electric charge. In a steady circuit, charge cannot build up at a point in a wire, so every coulomb that arrives each second must also depart. If you count currents in as positive and currents out as negative, the rule becomes
In the parallel circuit below, the current from the battery splits into three branches. The branch currents
Here is the junction rule, Kirchhoff's first law, with each symbol and its SI unit.
| Symbol | Quantity | SI unit |
|---|---|---|
| currents entering a junction | ampere (A) | |
| currents leaving the junction | ampere (A) |
Valid for: conservation of charge at any junction.
Example 1 The missing current at a junction
Two wires carry currents of 1.8 A and 0.7 A into a junction on a circuit board. Two wires leave it, and one of them carries 1.1 A. What current flows in the other outgoing wire? Call the incoming currents I₁ and I₂ and the known outgoing current I₃.
- Given:
- I_1:
- I_2:
- I_3:
- I_1:
- Formula:
- Substitute:
- Answer:
The answer is positive, so the guessed direction (out of the junction) is correct. A negative answer would mean the current actually flows in.

What Is Kirchhoff's Voltage Law?
Kirchhoff's voltage law, also called the loop rule or the second law, says that the sum of all the voltage changes around any closed loop is zero:
This follows from conservation of energy. The potential difference between two points depends only on the points, not on the path between them. Start at one point, go all the way around and return, and the net change has to be zero.
In the series loop below, a 12 V battery drives current through three resistors, and a voltmeter reads the drop across each one. Whatever the individual values, they add back to the battery voltage. The second worked example uses exactly this idea.
Example 2 The voltage across the third resistor
A 12 V battery drives current around a single loop with three resistors. A voltmeter reads 3.5 V across the first and 5.2 V across the second. What voltage drop appears across the third resistor?
- Given:
- ε:
- ΔV_1:
- ΔV_2:
- ε:
- Formula:
- Substitute:
- Answer:
The battery's rise must be used up exactly by the drops, so the three resistor voltages always add up to the battery voltage.

How Do You Choose Signs in Kirchhoff's Laws?
Most mistakes with Kirchhoff's laws are sign mistakes, so it pays to follow a fixed routine. Pick a direction for each unknown current and draw an arrow. You do not need to guess correctly; a negative answer simply means the current runs the other way.
- Resistor, walking with the current: the potential drops, so write
. - Resistor, walking against the current: the potential rises, so write
. - Battery, walking from − to +: the potential rises by its emf, so write
. - Battery, walking from + to −: the potential drops, so write
.
Pick a walking direction for each loop, apply these signs term by term, and set the total to zero. The same rules work whether you walk clockwise or counterclockwise.
How Do You Solve a Circuit With Kirchhoff's Laws?
A reliable method works for circuits of any size:
- Label every junction and give each branch a current with an assumed direction.
- Write the junction rule at all but one junction. The last one would repeat information you already have.
- Choose enough independent loops so that every branch is in at least one, and write the loop rule for each.
- Use Ohm's law,
, for every resistor term. - Solve the equations together, then check that each junction balances.
The diagram below shows a 12 V battery, a 4 Ω resistor and a parallel pair of 6 Ω and 12 Ω resistors. The outer loop and the inner loop give two loop equations, and the split point gives one junction equation. The third worked example finds the battery current, and the table that follows lists every branch current and voltage.
Example 3 Current from the battery in a two-loop circuit
A 12 V battery feeds a 4 Ω resistor R₁, which then splits into a 6 Ω resistor R₂ and a 12 Ω resistor R₃ in parallel. The parallel pair acts like a single 4 Ω resistor, so the outer loop rule gives 12 V = I × (4 Ω + 4 Ω), a total of 8 Ω. What current leaves the battery?
- Given:
- voltage across the resistor:
- resistance:
- voltage across the resistor:
- Formula:
- Substitute:
- Answer:
The table below breaks this current into the two branch currents and shows every voltage drop around both loops.
| Element | Current (A) | Voltage (V) | Kirchhoff check |
|---|---|---|---|
| Battery | 1.5 | +12 (rise) | Supplies the total current |
| R₁ = 4 Ω | 1.5 | 6 | Carries the full battery current |
| R₂ = 6 Ω | 1.0 | 6 | Inner loop: 6 V on R₂ = 6 V on R₃ |
| R₃ = 12 Ω | 0.5 | 6 | Junction: 1.0 A + 0.5 A = 1.5 A |
| Outer loop | 12 − 6 − 6 = 0 | Loop rule satisfied | |
| Source: Computed with Kirchhoff's junction and loop rules and V = IR; ideal battery and wires · Retrieved October 2026 | |||

Who Discovered Kirchhoff's Laws?
The German physicist Gustav Kirchhoff first described both circuit laws in 1845, while he was still a student. He built on Georg Ohm's work on resistance and extended it from single wires to whole networks of conductors.
Kirchhoff went on to make major contributions elsewhere in physics. He worked out laws of thermal radiation and, with the chemist Robert Bunsen, founded spectroscopy, the study of the colors of light that each chemical element gives off.
His circuit laws are now taught in every introductory electricity course and used daily by electrical engineers. Circuit simulation software applies them automatically to networks with thousands of nodes.
Where Are Kirchhoff's Laws Used?
Kirchhoff's laws work quietly behind many familiar systems:
- Home wiring. Every outlet on a circuit is a branch, and the current in the main cable equals the sum of the branch currents, which is why too many appliances can overload it.
- Car electrics. A car battery and alternator both feed the same network, and the loop rule shows how the load shares between them.
- Sensor bridges. A Wheatstone bridge is solved with the loop rule to find an unknown resistance precisely.
- Battery packs. Cells wired in parallel share current, and the junction rule shows how much each one supplies.
- Circuit design software. Programs that simulate chips and circuit boards set up Kirchhoff's equations at every node and solve them all at once.

Going Deeper: When Do Kirchhoff's Laws Break Down?
Kirchhoff's laws assume a lumped circuit, where each part is small compared with the distance an electromagnetic wave travels during one cycle of the signal. For household currents and ordinary electronics this is an excellent approximation.
At very high frequencies, such as radio and microwave circuits, wires behave like antennas and transmission lines. Changing magnetic fields then induce voltages along the path itself, and the simple loop rule no longer accounts for everything. Engineers use the full field equations of electromagnetism instead.
The junction rule also needs care with capacitors. Charge does pile up on a capacitor plate, but an equal charge leaves the other plate, so the rule still works when you treat the whole capacitor as one element. For steady DC circuits, both laws hold exactly.
Practice Kirchhoff's Law Problems
Start with single-loop circuits, then move to two-loop circuits with two batteries. Our series and parallel circuits worksheets include printable answer keys, and the resistors in series and parallel calculator checks any combination. Then try the quiz below.
Common Misconceptions
Myth: Current gets weaker as it passes through each resistor in a loop.
Physics: In a single loop the current is the same everywhere. What decreases across each resistor is the electric potential, not the current.
Myth: You must guess the right direction for every current before using Kirchhoff's laws.
Physics: Any direction works. If you guess wrong, the solved current just comes out negative, and its size is still correct.
Myth: The loop rule only applies to the outer edge of a circuit.
Physics: It applies to every closed path, including inner loops. You need one independent loop equation for each extra unknown.
Myth: Kirchhoff's laws replace Ohm's law.
Physics: They work together. Kirchhoff's laws give the equations for the network, and Ohm's law supplies the voltage across each resistor.
Key Facts
- Kirchhoff's current law says the total current into a junction equals the total current out.
- Kirchhoff's voltage law says the voltage changes around any closed loop add up to zero.
- The current law comes from conservation of charge; the voltage law comes from conservation of energy.
- A negative answer for a current simply means it flows opposite to the direction you assumed.
- Walking across a resistor in the direction of the current gives a voltage drop of −IR.
- Gustav Kirchhoff described both laws in 1845, while still a student.
- The laws hold for steady circuits but need extra care at very high frequencies.
Quick Quiz: How Well Do You Know Kirchhoff's Circuit Laws?
6 questions. Tap an answer to check it.
Currents of 2 A and 3 A flow into a junction. One wire leaves it. What current does it carry?
By the junction rule, the current out equals 2 A + 3 A = 5 A.
Kirchhoff's voltage law is a consequence of which principle?
The loop rule expresses energy conservation for charges moving around a closed path.
A 9 V battery drives current through two resistors in series. One has 4 V across it. What is the voltage across the other?
The drops must add to the battery voltage: 9 V − 4 V = 5 V.
You solve a circuit and get a current of −0.3 A. What does the minus sign mean?
A negative result just means the current runs the other way, with a size of 0.3 A.
When you walk across a resistor in the same direction as the current, the potential change is:
Current flows from high to low potential through a resistor, so the potential drops by IR.
In which year did Gustav Kirchhoff first describe his circuit laws?
Kirchhoff described both laws in 1845.
Frequently Asked Questions
What are Kirchhoff's two laws?
Kirchhoff's current law says the total current entering a junction equals the total current leaving it. Kirchhoff's voltage law says the sum of all voltage rises and drops around any closed loop is zero. The first follows from conservation of charge and the second from conservation of energy. Together they let you solve any network of batteries and resistors.
What is Kirchhoff's first law?
Kirchhoff's first law is the current law, also called the junction rule. At any point where wires meet, the currents flowing in add up to the currents flowing out. For example, if 3 A flows into a junction and one outgoing wire carries 1 A, the other outgoing wire must carry 2 A. No charge is created or lost at the junction.
What is Kirchhoff's second law?
Kirchhoff's second law is the voltage law, or loop rule. Around any closed loop in a circuit, the voltage gained from batteries equals the voltage lost across resistors and other components, so the total change is zero. In a single loop with a 9 V battery and two resistors, the two resistor voltages must add up to 9 V.
Why is Kirchhoff's current law true?
It is true because electric charge is conserved and, in a steady circuit, charge does not pile up at any point in the wires. Every coulomb that arrives at a junction each second has to leave it during that same second. If charge did accumulate, the junction would quickly build up a large voltage that would push the extra charge away.
Why is Kirchhoff's voltage law true?
It is true because electric potential at a point has a single value. If you start at one point, travel around a closed loop and return, the potential is the same as when you left, so the total of all the rises and drops must be zero. This is the circuit version of conservation of energy for each unit of charge.
How do you apply Kirchhoff's laws to a circuit?
Label each branch current with an assumed direction. Write the junction rule at each junction except one. Choose independent loops and write the loop rule for each, using −IR when you cross a resistor along the current and +ε when you cross a battery from negative to positive. Then solve the equations together and check the results.
What is the difference between Kirchhoff's laws and Ohm's law?
Ohm's law describes a single component: the voltage across a resistor equals current times resistance. Kirchhoff's laws describe how the components connect: how currents divide at junctions and how voltages add around loops. Ohm's law alone cannot solve a circuit with several branches and sources, and Kirchhoff's laws need Ohm's law to relate each voltage to a current.
Do Kirchhoff's laws work for AC circuits?
Yes, as long as the frequency is low enough that the circuit is small compared with the wavelength of the signal. You then apply the rules to the instantaneous currents and voltages, or to phasors that include phase. At radio and microwave frequencies, wires act like antennas and transmission lines, and engineers switch to the full electromagnetic field equations.
Sources
Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.








