One path for the current

Series Circuits

A series circuit is a circuit in which every component sits on a single loop, so the same current flows through each part one after another. The total resistance is the sum of the individual resistances, and the battery voltage is shared out among the components. Break the loop anywhere and the current stops everywhere, which is why one dead bulb can darken a whole string.

Three small bulbs wired one after another to a battery holder on a lab bench, a simple series circuit with all bulbs lit
Three bulbs on one loop share the same current and split the battery's voltage between them.

At a Glance

A series circuit connects components end to end in one loop, so the current I is the same everywhere. The total resistance is R_s = R1 + R2 + R3 + ..., and the source voltage splits between the components so that V = V1 + V2 + V3. If any part breaks, the whole circuit stops working.

Number of paths
One single loop
Current
Same through every component
Voltage
Shared: V = V1 + V2 + V3
Total resistance
Rs = R1 + R2 + R3 + …
If one part fails
The whole circuit stops
Unit of resistance
ohm (Ω)
On this page
  1. What Is a Series Circuit?
  2. Series Circuits Explained Simply
  3. Is the Current the Same Everywhere in a Series Circuit?
  4. How Is Voltage Divided in a Series Circuit?
  5. How Do You Calculate Total Resistance in a Series Circuit?
  6. What Happens When You Add More Bulbs in Series?
  7. What Happens If One Bulb Breaks in a Series Circuit?
  8. What Are the Advantages and Disadvantages of Series Circuits?
  9. Where Are Series Circuits Used in Everyday Life?
  10. Going Deeper: Internal Resistance and Cells in Series
  11. Practice Series Circuit Problems
  12. Common Misconceptions
  13. Key Facts
  14. Quiz
  15. FAQ

What Is a Series Circuit?

A series circuit is the simplest way to join parts into a working electric circuit. Each component connects to the next like beads on a necklace, and the last one connects back to the source. Charge leaving the battery has exactly one route to follow before it returns.

That single route sets all the rules. The current cannot split, so it is the same at every point. The voltage of the source has to be shared between the components, and their resistances stack up into one larger total.

The other basic arrangement is the parallel circuit, where each component gets its own branch. Our side-by-side guide to series vs parallel circuits compares the two in detail, while this page focuses on series wiring alone.

Series Circuits Explained Simply

Picture a narrow hiking trail with three gates along it and no side paths. Every hiker must pass through gate one, then gate two, then gate three. If the trail is crowded at one gate, it is crowded at all of them, because nobody can go around.

Electric charge in a series circuit behaves the same way. The battery is like a ski lift that raises the hikers back to the start, giving them energy. Each gate they pass through takes a share of that energy, and by the time they reach the bottom, all of it has been used up.

Close one gate and the whole trail stops moving. That is the weakness of series wiring: a single open switch, blown fuse or broken filament stops the current in every part of the loop.

Is the Current the Same Everywhere in a Series Circuit?

Yes. Charge is conserved and it cannot pile up inside a wire, so the amount of charge passing any point each second must be the same all the way around a single loop. An ammeter placed before the first resistor, between two resistors or after the last one will show identical readings.

A common mistake is to imagine that the first bulb "uses up" some of the current, leaving less for the next one. Current is not consumed. What the components use up is energy, and that shows up as a drop in voltage, not a drop in current.

To find the current, divide the source voltage by the total resistance using Ohm's law, first published by Georg Ohm, I=V/Rs. The Ohm's law calculator does this step for you with any combination of units.

Example 2 Current through a string of holiday lights

An old-style string of decorative lamps wired in series has a total resistance of 480 Ω and is plugged into a 120 V outlet. What current flows through every lamp in the string?

  1. Given:
    • voltage across the resistor: V=120 V
    • resistance: R=480 Ω
  2. Formula: I=VR
  3. Substitute: I=(120 V)(480 Ω)
  4. Answer: I=0.25 A

Because there is only one path, this same current passes through the first lamp, the last lamp and every lamp between them.

How Is Voltage Divided in a Series Circuit?

The source voltage is split among the components, and the drops always add up to the total: V=V1+V2+V3. This is a direct result of energy conservation, and it is the idea behind Kirchhoff's loop rule, named after Gustav Kirchhoff.

The share each component takes depends on its resistance. Since the current is the same for all of them, the voltage across each one is Vn=IRn. A resistor with twice the resistance gets twice the voltage, so the largest resistor always has the largest drop.

Engineers use this sharing on purpose. Two resistors in series form a voltage divider, which turns a 9 V supply into a smaller voltage for a sensor. You can try values in the voltage divider calculator.

Example 3 The voltage drop across one resistor

In a series circuit the current is 0.25 A. One of the components is an 18 Ω resistor. What is the voltage across that resistor?

  1. Given:
    • current: I=0.25 A
    • resistance: R=18 Ω
  2. Formula: V=IR
  3. Substitute: V=(0.25 A)(18 Ω)
  4. Answer: V=4.5 V

Repeat this for each component and the drops add up to the source voltage, which is a handy way to check your work.

A 12 V battery with 10 Ω, 20 Ω and 30 Ω resistors in series
ComponentResistance (Ω)Current (A)Voltage drop (V)Power (W)
R1100.220.4
R2200.240.8
R3300.261.2
Whole circuit600.2122.4
Source: Computed with R_s = R1 + R2 + R3, I = V / R_s, V_n = I R_n and P = I V · Retrieved October 2026
Series circuit diagram: 12 V battery, 10, 20 and 30 ohm resistors and an ammeter on one loop with a single current I
One loop, one current: the 12 V supply is shared as 2 V, 4 V and 6 V across the three resistors.

How Do You Calculate Total Resistance in a Series Circuit?

In series, resistances simply add: Rs=R1+R2+R3+⋯. Each resistor is one more obstacle the same current must push through, so every addition makes the total larger. Ten identical 100 Ω resistors in a row behave exactly like one 1,000 Ω resistor.

Once you know the total, three steps solve almost any series problem. Find Rs by adding, find the current with I=V/Rs, then find each voltage drop with Vn=IRn. Our formula page on resistors in series and parallel covers the derivation, and the series and parallel resistor calculator handles long chains.

Here is the series resistance formula with each symbol and its SI unit. It works for any number of resistors placed end to end.

Rs=R1+R2+R3+⋯
What each symbol means
SymbolQuantitySI unit
Rsequivalent series resistanceohm (Ω)
R1resistance 1ohm (Ω)
R2resistance 2ohm (Ω)
R3resistance 3ohm (Ω)

Valid for: same current through each resistor.

Example 1 Three resistors on a breadboard

A student places resistors of 15 Ω, 33 Ω and 22 Ω one after another on a breadboard, forming a single path. What is the total resistance of the chain?

  1. Given:
    • resistance 1: R1=15 Ω
    • resistance 2: R2=33 Ω
    • resistance 3: R3=22 Ω
  2. Formula: Rs=R1+R2+R3+⋯
  3. Substitute: R1=15 Ω,R2=33 Ω,R3=22 Ω
  4. Answer: Rs=70 Ω

The total is always larger than the largest single resistor, a quick check that you added rather than averaged.

What Happens When You Add More Bulbs in Series?

Every bulb you add raises the total resistance, so the current through the loop falls. Because the same smaller current now flows through each bulb, every bulb glows more dimly than before. The table below shows identical 12 Ω bulbs on a 6 V battery.

The drop in brightness is steep. Power in each bulb depends on the square of the current, P=I2R, so halving the current cuts each bulb's power to a quarter. With four bulbs in the loop, each one receives only a small fraction of the power a single bulb would get.

There is a quiet benefit too. The battery's total power output falls as you add bulbs, so a long series string drains a battery more slowly, just with less light.

Identical 12 Ω bulbs in series on a 6 V battery
Bulbs in seriesTotal resistance (Ω)Current (A)Power per bulb (W)Total power (W)
1120.533
2240.250.751.5
3360.1670.3331
4480.1250.1880.75
Source: Computed with I = V / R_s and P = I² R; bulb resistance treated as constant (real filaments change with temperature) · Retrieved October 2026

What Happens If One Bulb Breaks in a Series Circuit?

If one bulb's filament snaps, the loop is open and the current drops to zero everywhere. Every other bulb goes dark at once, even though they are all perfectly fine. Finding the faulty one means checking each bulb in turn.

This is exactly what a switch or a fuse is designed to do. A switch placed anywhere in a series loop controls every component on it. A fuse or circuit breaker in series with an appliance cuts the whole current when it becomes dangerously high, which is why fuses and circuit breakers are always wired in series.

Some modern light strings get around the problem with a tiny shunt inside each bulb. When a filament fails, the shunt closes the gap so the rest of the string stays lit.

Unlit string of mini lights on a table with one loose bulb in focus, showing how one break stops a series circuit
In an old series light string, one loose bulb opens the loop and the whole string goes dark.
Series circuit with a 6 V battery, an open switch and three bulbs; the open switch breaks the only path so no current flows
With the switch open there is no complete path, so none of the three bulbs can light.

What Are the Advantages and Disadvantages of Series Circuits?

  • Simple to build: one loop of wire and no junctions make series circuits cheap and easy to trace.
  • One control point: a single switch or fuse can control or protect every component.
  • Adds up voltage sources: cells placed in series add their voltages, which is how a flashlight gets 3 V from two 1.5 V cells.
  • Single point of failure: one broken part stops everything on the loop.
  • Shared voltage: each device gets only part of the supply, so household appliances cannot be wired this way.
  • Dimming: adding loads lowers the current for all of them.

Because of the last two points, homes use parallel wiring for outlets and lights. Series connections are kept for the jobs where one shared current is exactly what you want.

Where Are Series Circuits Used in Everyday Life?

Look inside a flashlight or a TV remote and you will find the cells stacked end to end in series, so their voltages add. A battery pack in a cordless drill or an electric car does the same with dozens or thousands of cells.

Wall switches sit in series with the lamp they control, and thermostats sit in series with the heater they switch. Many sensors use a resistor in series with a thermistor or light-dependent resistor so that a changing temperature or light level becomes a changing voltage. Our list of series and parallel circuit examples sorts dozens more.

An ammeter must always be connected in series with the part it measures, so that the current it reads is the same current that flows through that part.

Going Deeper: Internal Resistance and Cells in Series

Real batteries have a small internal resistance, so they behave like an ideal source in series with a tiny resistor. When the outside circuit draws more current, more voltage is lost inside the battery, and the voltage at its terminals falls a little. Our page on electromotive force explains this in full.

Cells in series add both their voltages and their internal resistances. That is fine for low-current gadgets but becomes a design limit for high-power packs. Capacitors also follow different rules from resistors when placed in series, as shown on capacitors in series and parallel.

Practice Series Circuit Problems

The best way to lock in the three rules is to solve problems with real numbers. Our printable series and parallel circuits worksheets come with answer keys, and the series and parallel circuits lab lets you measure the rules with a battery, bulbs and a meter. Younger learners can start with circuits for kids, then try the quiz below.

Common Misconceptions

Myth: The first bulb in a series circuit gets the most current and the last bulb gets the least.

Physics: Current is the same at every point of a single loop. Bulbs use up energy, which shows as voltage drops, not current.

Myth: Adding another resistor in series lets more current flow because there is more to conduct through.

Physics: Each added resistor raises the total resistance, so the current through the loop goes down.

Myth: Every component in a series circuit gets the full battery voltage.

Physics: The battery voltage is shared. The drops across the components add up to the supply voltage.

Myth: The order of the components in a series loop changes how bright each bulb is.

Physics: Order does not matter in a simple series loop. The same current flows through each part wherever it sits.

Key Facts

  • A series circuit has only one path, so the same current flows through every component.
  • The total resistance of resistors in series is the sum of their resistances.
  • The voltage drops across the components add up to the source voltage.
  • The largest resistor in a series loop always takes the largest share of the voltage.
  • Adding more bulbs in series lowers the current and makes every bulb dimmer.
  • If any single component breaks, current stops in the entire series circuit.
  • Switches, fuses and ammeters are always connected in series with what they control or measure.
Did you know? Early holiday light strings were wired fully in series, so one loose bulb could leave an entire tree dark, and families sometimes spent an evening swapping bulbs one at a time to find the culprit.

Quick Quiz: How Well Do You Know Series Circuits?

6 questions. Tap an answer to check it.

  1. In a series circuit, how does the current through the second resistor compare with the current through the first?

  2. Resistors of 5 Ω, 10 Ω and 25 Ω are connected in series. What is the total resistance?

  3. A 9 V battery is connected to two resistors in series. The first has 3 V across it. What is the voltage across the second?

  4. What happens to the other bulbs if one bulb in a series string burns out?

  5. Which resistor in a series circuit has the largest voltage drop?

  6. Why is an ammeter connected in series?

Frequently Asked Questions

What is a series circuit in simple terms?

A series circuit is a loop where all the parts are connected one after another, with only one path for electricity to follow. The same current flows through each part in turn. If you open the loop anywhere, for example by removing one bulb or flipping a switch, the current stops and every part on the loop turns off.

What are the three rules of a series circuit?

First, the current is the same at every point in the circuit. Second, the voltage drops across the components add up to the source voltage. Third, the total resistance equals the sum of the individual resistances. With these three rules and Ohm's law you can find the current and the voltage across every component in any series circuit.

How do you find the current in a series circuit?

Add all the resistances to get the total resistance, then divide the source voltage by that total using Ohm's law, I = V / R. For example, a 9 V battery driving resistors that add up to 450 ohms gives a current of 0.02 A. That same current flows through every component, so you only need to calculate it once.

Why does voltage drop in a series circuit?

Each component converts some of the electrical energy carried by the charge into heat, light or motion. Voltage measures energy per unit of charge, so when charge passes through a component and gives up energy, the voltage falls. The total of all these drops equals the energy per charge the battery supplied, so the drops add up to the battery voltage.

Why are bulbs dimmer in series?

Adding bulbs in series raises the total resistance, which lowers the current through the whole loop. Each bulb also receives only part of the battery voltage. With less current and less voltage, each bulb converts less power into light. Two identical bulbs in series each get a quarter of the power one bulb alone would receive from the same battery.

Are houses wired in series or parallel?

Houses are wired in parallel. Each outlet and light gets the full supply voltage and can be switched on or off without affecting the others. If a house were wired in series, turning off one lamp would cut power to every device, and each appliance would receive only part of the voltage. Switches and fuses, however, are placed in series with what they control.

Is a battery with two cells a series circuit?

When cells are stacked end to end, positive terminal to negative terminal, they are connected in series and their voltages add. Two 1.5 V cells in series give 3 V, and four give 6 V. The same current flows through every cell. This is how flashlights, remotes and toys reach the voltage they need from small cells.

What is the formula for a series circuit?

The key formula is R_s = R1 + R2 + R3 and so on for total resistance. Combine it with Ohm's law, I = V / R_s, to get the current, and with V_n = I R_n to get the voltage across each resistor. Finally, the individual voltages always add up to the source voltage, which gives you a built-in check on your answers.

What happens to resistance in a series circuit when you add a resistor?

The total resistance goes up by exactly the value of the resistor you add. A 20 ohm resistor added to a chain that already totals 50 ohms makes 70 ohms. Because the total is larger, the current from the same battery becomes smaller. This is the opposite of a parallel circuit, where adding a branch lowers the total resistance.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.