Current against voltage

Ohmic and Non-Ohmic Conductors (I-V Characteristics)

An ohmic conductor is one whose current is directly proportional to the voltage across it, so its resistance stays constant and its I-V graph is a straight line through the origin. A non-ohmic conductor breaks that rule: its resistance changes as the voltage or current changes, so its I-V graph curves. Metal resistors at steady temperature are ohmic, while filament lamps and diodes are not.

Glowing filament bulb beside a coil of bare wire, comparing a non-ohmic lamp with an ohmic metal conductor
A coil of wire at room temperature behaves ohmically; a glowing lamp filament does not.

At a Glance

An ohmic conductor obeys Ohm's law, V = I R, with a constant R, so a graph of current I against voltage V is a straight line through the origin. A non-ohmic conductor, such as a filament lamp, a diode or a thermistor, has a resistance that changes with voltage, current or temperature, so its I-V graph is curved.

Ohmic test
I proportional to V, so V/I stays constant
Key relation
V = I R (R constant only for ohmic parts)
SI unit of resistance
ohm (Ω), equal to 1 V/A
Ohmic I-V graph
Straight line through the origin
Non-ohmic examples
Filament lamp, diode, LED, thermistor, LDR
Named after
Georg Ohm, who published his law in 1827
On this page
  1. What Is an Ohmic Conductor?
  2. Ohmic and Non-Ohmic Conductors Explained Simply
  3. How Do You Tell If a Conductor Is Ohmic?
  4. What Do I-V Characteristic Graphs Look Like?
  5. Why Is a Filament Lamp Non-Ohmic?
  6. Why Is a Diode Non-Ohmic?
  7. What Are Examples of Ohmic and Non-Ohmic Conductors?
  8. What Is the Resistance of a Non-Ohmic Component?
  9. How Can You Measure an I-V Characteristic?
  10. Why Does Ohmic Behavior Matter in Real Circuits?
  11. Common Misconceptions
  12. Key Facts
  13. Quiz
  14. FAQ

What Is an Ohmic Conductor?

An ohmic conductor is any material or component that follows Ohm's law over its working range. Double the voltage across it and the current doubles; triple the voltage and the current triples. The ratio of voltage to current, which is its resistance, stays the same the whole time.

A non-ohmic conductor is everything else. Its current still rises when you raise the voltage, at least in most cases, but not in a fixed proportion. Its resistance depends on how hard you drive it, how hot it gets, how much light falls on it, or which way the current flows.

The word "ohmic" describes behavior, not a type of material. A copper wire is ohmic while it stays near room temperature, yet the very same metal, drawn into a thin coil and heated until it glows, behaves in a clearly non-ohmic way.

Ohmic and Non-Ohmic Conductors Explained Simply

Think of a conductor as a hallway that charge has to walk through. In an ohmic conductor the hallway never changes. Push twice as hard and twice as many charges get through each second.

In a non-ohmic conductor the hallway changes as you use it. In a filament lamp, the harder you push, the hotter the hallway gets and the more crowded and jostling it becomes, so each extra push gains you less. In a diode, the hallway has a door that stays almost shut until the push reaches a certain strength, then swings wide open, and it will not open at all from the other side.

If you plot current against voltage, the unchanging hallway gives a straight line. Any change in the hallway bends that line.

How Do You Tell If a Conductor Is Ohmic?

The test is simple: measure the current through the component at several different voltages and check whether V/I gives the same answer each time. If it does, the component is ohmic and V=IR holds with a single value of R. If the ratio drifts up or down, the component is non-ohmic.

A graph makes the test quicker. Plot current on the vertical axis and voltage on the horizontal axis. An ohmic conductor gives a straight line that passes through the origin, and the gradient of that line is 1/R. A steep line means a small resistance; a shallow line means a large one.

Both conditions matter. A straight line that misses the origin, or a line through the origin that bends, both point to non-ohmic behavior. You can try the measurement yourself with our Ohm's law I-V graph experiment, or check single values with the Ohm's law calculator.

Ohm's law links voltage, current and resistance; a conductor is ohmic when R in this equation does not change as V changes.

V=IR
What each symbol means
SymbolQuantitySI unit
Vvoltage across the resistorvolt (V)
Icurrentampere (A)
Rresistanceohm (Ω)

Rearranged to find another variable:

I=VRR=VI

Valid for: ohmic conductors (R independent of V and I).

Example 1 Testing a length of nichrome wire

A student connects a short length of nichrome wire to a variable supply. At 1.8 V the ammeter reads 0.24 A, and at every other setting the ratio of voltage to current turns out the same. What is the resistance of the wire?

  1. Given:
    • voltage across the resistor: V=1.8 V
    • current: I=0.24 A
  2. Formula: R=VI
  3. Substitute: R=(1.8 V)(0.24 A)
  4. Answer: R=7.5 Ω

Because the ratio V/I is the same at every setting, this single value describes the wire, which is exactly what makes it ohmic.

What Do I-V Characteristic Graphs Look Like?

An I-V characteristic is the graph of current against voltage for one component. Each common part has a shape you can learn to recognize at a glance:

  • Fixed resistor at constant temperature: a straight line through the origin, the same in both directions. Reverse the voltage and the current reverses by the same amount.
  • Filament lamp: steep near the origin, then flattening out as the voltage rises. It is symmetric, so the curve for negative voltage mirrors the positive side.
  • Diode: almost flat at zero current for reverse voltage and for small forward voltages, then rising very sharply once the forward voltage passes about 0.6 V for silicon.
  • Thermistor: the curve bends upward as self-heating lowers its resistance, the opposite way to a lamp.

The table compares an 8 Ω resistor with a 12 V lamp that also draws 1.5 A at full voltage. They agree at 12 V, yet at every lower voltage the cooler lamp filament lets through more current than the resistor does.

Current through an 8 Ω resistor and a 12 V filament lamp at the same voltages
Voltage (V)Resistor current (A)Lamp current (A)Lamp resistance V/I (Ω)
10.1250.3382.96
20.2500.5123.91
40.5000.7765.16
60.7500.9906.06
81.0001.1766.80
101.2501.3457.44
121.5001.5008.00
Source: Computed: resistor I = V/R with R = 8 Ω; lamp from the simple model I = 1.5 A × (V/12 V)^0.6, a typical approximation for tungsten filaments · Retrieved October 2026

Why Is a Filament Lamp Non-Ohmic?

A filament lamp is a thin coil of tungsten. When current flows, the wire heats up, and in a hot metal the atoms vibrate more strongly. Free electrons drifting through the metal collide with those vibrating atoms more often, so the resistance rises with temperature.

Low voltage means a small current, a cool filament and a low resistance, so the I-V curve starts steep. As the voltage climbs, the filament reaches a white-hot glow and its resistance grows several times larger. Each extra volt then adds less current, and the curve flattens.

The filament itself is still a metal; it would be close to ohmic if you could hold its temperature fixed. The lamp is non-ohmic because its own current changes its temperature. That is also why a lamp most often fails at the moment you switch it on: the cold filament briefly draws a surge of current several times its normal value.

Example 2 A car lamp at full brightness

A 12 V lamp draws 1.5 A when it glows at full brightness. What is the resistance of its hot filament?

  1. Given:
    • voltage across the resistor: V=12 V
    • current: I=1.5 A
  2. Formula: R=VI
  3. Substitute: R=(12 V)(1.5 A)
  4. Answer: R=8 Ω

Measured cold with a multimeter, the same filament reads only a fraction of this value, because tungsten's resistance climbs as it heats up.

Why Is a Diode Non-Ohmic?

A diode is made from two layers of semiconductor joined together. At the junction there is a thin region with almost no free charge carriers, which acts like a barrier. A forward voltage has to push the carriers over that barrier, and the number that make it across grows exponentially with the voltage.

The result is a dramatic curve. In the computed values below, raising a silicon diode from 0.60 V to 0.70 V, only a tenth of a volt, multiplies the current almost fifty times. Reverse the voltage and the barrier grows wider, so only a tiny leakage current flows until, at a much higher reverse voltage, the diode breaks down.

Light-emitting diodes behave the same way with a larger turn-on voltage, typically about 1.8 V for red and around 3 V for blue or white. Their steep curve is why an LED always needs a series resistor to limit its current.

Example 3 The resistance of a diode at one operating point

A silicon diode carries 5.75 mA (0.00575 A) when 0.70 V is across it in the forward direction. What is the ratio V/I at this point?

  1. Given:
    • voltage across the resistor: V=0.7 V
    • current: I=0.00575 A
  2. Formula: R=VI
  3. Substitute: R=(0.7 V)(0.00575 A)
  4. Answer: R=121.7 Ω

At 0.60 V the same diode passes about 0.12 mA, giving a ratio near 5,000 Ω, so this number only holds at this one point on the curve.

Forward current and V/I ratio of a typical small silicon diode
Forward voltage (V)CurrentV/I ratio
0.301.1 nA274 MΩ
0.4052 nA7.6 MΩ
0.502.5 µA199 kΩ
0.600.120 mA5.0 kΩ
0.650.831 mA782 Ω
0.705.75 mA122 Ω
0.7539.8 mA18.9 Ω
Source: Computed with the ideal diode equation I = I_s(e^(V/V_T) − 1), I_s = 1 × 10⁻¹⁴ A (typical), V_T = kT/e at 300 K from CODATA 2022 constants · Retrieved October 2026
Row of LEDs on a breadboard with one glowing red, a non-ohmic diode conducting in its forward direction
An LED stays dark until its forward voltage is reached, then its current rises very steeply.
Circuit diagram of a 5 volt battery, a 150 ohm resistor and an LED in series
Because an LED is non-ohmic, a series resistor sets its current instead of the LED itself.

What Are Examples of Ohmic and Non-Ohmic Conductors?

Ohmic, at least within normal limits:

  • Metal-film and carbon-film resistors used in electronics
  • Copper and aluminum wires at steady temperature
  • Nichrome and constantan resistance wire, which change very little as they warm
  • Salt water between metal plates, over short measurements

Non-ohmic:

  • Filament lamps, whose resistance rises as they heat up
  • Diodes and LEDs, which conduct well in one direction only
  • Thermistors and light-dependent resistors, built on purpose to change resistance with temperature or light
  • Transistors, gas discharge tubes and neon lamps
  • Sparks and lightning, where the air suddenly becomes a conductor

What Is the Resistance of a Non-Ohmic Component?

For a non-ohmic part, "the resistance" needs a qualifier, because there is a different value at every point on the curve. The usual choice is the ratio R=V/I at the operating point, sometimes called the static or chord resistance. That is what the worked examples on this page calculate.

Engineers often also use the dynamic, or incremental, resistance: the change in voltage divided by the change in current, r=ΔV/ΔI, read from the slope of the curve near the operating point. For a resistor the two values match. For a diode at a few milliamperes they differ a lot, and the dynamic value is the one that controls how small signals pass through it.

Ohm's law in the form V=IR still holds at any single instant for a non-ohmic part, as long as you use the resistance at that point. What fails is the idea that one fixed R describes the component at every voltage.

How Can You Measure an I-V Characteristic?

You need a variable voltage source, the component under test, an ammeter in series and a voltmeter in parallel across the component. Our page on the ammeter and voltmeter explains why they are connected that way, and a single multimeter can do either job.

  1. Set the supply to zero, then raise it in small steps.
  2. At each step record the voltmeter and ammeter readings.
  3. Reverse the component, or the supply, and repeat to get negative values.
  4. Plot current against voltage and look at the shape.

Keep currents modest and leave a pause between readings for a lamp, so its temperature settles. A diode or LED must always have a series resistor, or a small change in voltage could send a damaging current through it.

Circuit with a variable supply, ammeter, rheostat and lamp in series, and a voltmeter connected across the lamp
The ammeter in the loop reads current while the voltmeter across the lamp reads its voltage at each step.

Why Does Ohmic Behavior Matter in Real Circuits?

Most circuit calculations, such as those for series circuits and voltage dividers, assume ohmic resistors with fixed values. That assumption is why designers choose metal-film resistors with tiny temperature coefficients for precise work.

Non-ohmic behavior is just as useful, as long as you expect it. Diodes turn alternating current into direct current, thermistors sense temperature in thermostats and battery packs, and the rising resistance of a lamp filament helps steady its own current. Knowing which kind of part you have tells you which tools to use: simple V=IR algebra for ohmic parts, the measured I-V curve for everything else.

For practice with the numbers, see our Ohm's law worksheets and the electricity formula sheet. The man behind the law is profiled on our Georg Ohm page, and the difference between the two quantities on each axis is covered in current vs voltage.

Common Misconceptions

Myth: Ohm's law applies to every conductor.

Physics: Ohm's law is not a universal law of nature. It describes the behavior of certain materials, mainly metals at steady temperature, and many useful components do not follow it.

Myth: A non-ohmic component has no resistance, or you cannot use V = IR for it.

Physics: V/I still gives a resistance at each point. The difference is that this value changes as the voltage changes, so one fixed R cannot describe the whole curve.

Myth: Any straight-line I-V graph means the conductor is ohmic.

Physics: The line must also pass through the origin. A straight line with an offset means the ratio V/I changes, so the part is not ohmic.

Myth: A filament lamp is non-ohmic because tungsten is a special material.

Physics: Tungsten is an ordinary metal. The lamp is non-ohmic because its own current heats the filament, and the resistance of the hot metal is much higher.

Key Facts

  • An ohmic conductor has a current directly proportional to the voltage across it, so its resistance is constant.
  • The I-V graph of an ohmic conductor is a straight line through the origin with a gradient equal to 1/R.
  • A filament lamp is non-ohmic because its resistance rises as the tungsten filament heats up.
  • A diode is non-ohmic and conducts well in only one direction, after a forward voltage of about 0.6 V for silicon.
  • Thermistors and light-dependent resistors are non-ohmic parts designed to change resistance with temperature or light.
  • For a non-ohmic component, V/I gives the resistance at one operating point only.
  • Most metals are ohmic only as long as their temperature stays steady.
Did you know? The tungsten filament of a typical household lamp has a resistance more than ten times higher when glowing than when cold, which is why the brief surge at switch-on is the moment most bulbs burn out.

Quick Quiz: How Well Do You Know Ohmic and Non-Ohmic Conductors (I-V Characteristics)?

6 questions. Tap an answer to check it.

  1. What does the I-V graph of an ohmic conductor look like?

  2. Why does the I-V graph of a filament lamp curve?

  3. A component passes 0.5 A at 2 V and 1.0 A at 4 V. What can you say about it?

  4. Which component conducts well in only one direction?

  5. On an I-V graph with current on the vertical axis, what is the gradient of an ohmic line?

  6. Which of these is a non-ohmic component?

Frequently Asked Questions

What is the difference between ohmic and non-ohmic conductors?

An ohmic conductor has a constant resistance, so the current through it is directly proportional to the voltage and its I-V graph is a straight line through the origin. A non-ohmic conductor has a resistance that changes with voltage, current, temperature or light, so its I-V graph is curved. Fixed resistors are ohmic; lamps, diodes and thermistors are non-ohmic.

Is a filament lamp ohmic or non-ohmic?

A filament lamp is non-ohmic. As more current flows, the tungsten filament gets hotter, and hot metal has a higher resistance than cold metal. Its I-V graph starts steep near zero and then flattens at higher voltages. The curve is the same shape for both directions of current, because the heating does not depend on which way the charge flows.

Is a diode an ohmic conductor?

No. A diode is strongly non-ohmic. Below a forward voltage of roughly 0.6 V for silicon, almost no current flows, and above it the current rises extremely steeply. In the reverse direction only a tiny leakage current flows until breakdown. Its resistance can range from many megaohms to a few ohms, depending on the voltage across it.

What does the gradient of an I-V graph tell you?

When current is on the vertical axis and voltage on the horizontal axis, the gradient of a straight line through the origin equals 1/R, the reciprocal of resistance. A steeper line means a smaller resistance. If the axes are swapped, with voltage on the vertical axis, the gradient equals R directly. Always check which quantity is on which axis before reading the slope.

Why are metals ohmic?

In a metal, a sea of free electrons drifts through a lattice of vibrating atoms. As long as the temperature stays the same, the rate at which electrons scatter off the atoms does not depend on the current, so the drift speed, and the current, is simply proportional to the applied voltage. Once the metal heats up, the scattering increases and the resistance rises.

Is a thermistor ohmic?

No. A thermistor is designed so that its resistance changes strongly with temperature. The common NTC type loses resistance as it warms, so if enough current flows to heat it, its I-V graph curves upward. At very small currents, where self-heating is negligible, it can look nearly ohmic at a fixed temperature, but its value still depends on the surroundings.

Do ohmic conductors stay ohmic forever?

Only within limits. Push enough current through any resistor and it heats up, so its resistance drifts and the straight-line graph starts to bend. At even higher currents it can be damaged. That is why resistors have a power rating, and why the ohmic description applies to the normal operating range rather than to every possible voltage.

How do you calculate resistance from an I-V graph?

Pick a point on the graph, read its voltage and current, and divide: R = V/I. For an ohmic conductor every point gives the same answer. For a non-ohmic component, the answer applies only to that point. To find how the resistance changes, repeat the calculation at several points along the curve and compare the results.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.