Opposition to current

Electrical Resistance

Electrical resistance is the opposition an object offers to the flow of electric current, equal to the voltage across it divided by the current through it. It is measured in ohms (Ω). A long, thin or hot wire resists more than a short, thick or cool one, and every real conductor turns some electrical energy into heat because of it.

Glowing coiled heating wires inside a toaster, where electrical resistance turns current into heat
A toaster's coiled wires have enough resistance to turn current into strong, steady heat.

At a Glance

Electrical resistance is how much an object opposes current, found with R = V / I, where V is voltage in volts and I is current in amperes, giving ohms (Ω). For a wire, R = ρ L / A, so resistance grows with length, shrinks with cross-sectional area and depends on the material's resistivity ρ.

Symbol
R
SI unit
ohm (Ω), equal to 1 V/A
Formula
R = V / I
For a wire
R = ρL / A
Scalar or vector
Scalar, never negative for ordinary materials
Depends on
Material, length, cross-sectional area and temperature
On this page
  1. What Is Electrical Resistance?
  2. Electrical Resistance Explained Simply
  3. What Is the Formula for Resistance?
  4. What Is the Unit of Resistance?
  5. What Factors Affect the Resistance of a Wire?
  6. Which Materials Have High and Low Resistance?
  7. How Does Temperature Affect Resistance?
  8. How Do Resistances Combine in a Circuit?
  9. Where Is Resistance Useful in Everyday Life?
  10. Why Does Resistance Produce Heat?
  11. Practice Resistance Problems
  12. Common Misconceptions
  13. Key Facts
  14. Quiz
  15. FAQ

What Is Electrical Resistance?

Resistance measures how hard it is to push electric current through something. Apply the same voltage to two objects and the one with the larger resistance lets less current through. A copper wire has very little resistance, a lamp filament has more, and a dry rubber glove has so much that almost no current flows at all.

Inside a metal, current is a slow drift of free electrons. As they move, they keep bumping into the vibrating atoms of the metal and into impurities and defects. Each collision hands some of the electrons' energy to the atoms, which jiggle harder, and that extra jiggling is heat. Resistance is the overall measure of this obstruction.

Resistance is a scalar with a single value for a given object at a given temperature. It depends on the object as a whole, its material, length and thickness, while the related quantity resistivity describes only the material.

Electrical Resistance Explained Simply

Imagine running down a hallway. If the hallway is empty and wide, you move easily. If it is narrow, very long or crowded with people, you get slowed down again and again. Electrons moving through a wire face the same kind of obstacles, and resistance is a number for how crowded and narrow their path is.

A thick wire is like a wide hallway, so it has low resistance. A long wire is like a long hallway, so it has more. Some materials, such as copper and silver, are naturally uncrowded for electrons. Others, such as rubber and glass, are so packed that electrons barely move at all.

What Is the Formula for Resistance?

Resistance is defined as the ratio of voltage to current: R=VI. Here V is the potential difference across the object in volts and I is the current through it in amperes, so R comes out in ohms. A resistance of 1 Ω lets a current of 1 A flow when 1 V is applied.

The same relation written as V=IR is Ohm's law. For many conductors at a steady temperature, R stays constant as the voltage changes, so a graph of current against voltage is a straight line. Components that behave this way are called ohmic; lamps, diodes and many sensors are not, as explained on our page about ohmic and non-ohmic conductors.

To solve for resistance, voltage or current with your own numbers, use the Ohm's law calculator, which shows every step.

Resistance is defined through the ratio of voltage to current. Here is the relation with each symbol and its SI unit, including the form solved for R.

V=IR
What each symbol means
SymbolQuantitySI unit
Vvoltage across the resistorvolt (V)
Icurrentampere (A)
Rresistanceohm (Ω)

Rearranged to find another variable:

I=VRR=VI

Valid for: ohmic conductors (R independent of V and I).

Example 1 Finding the resistance of a heating pad element

A 9.0 V battery drives a current of 0.030 A through a small heating element. What is the resistance of the element?

  1. Given:
    • voltage across the resistor: V=9 V
    • current: I=0.03 A
  2. Formula: R=VI
  3. Substitute: R=(9 V)(0.03 A)
  4. Answer: R=300 Ω

Hundreds of ohms is typical for small low-power parts; large heaters running on mains voltage have far lower resistance so they can draw more current.

What Is the Unit of Resistance?

The SI unit of resistance is the ohm, written with the Greek letter omega, Ω. One ohm equals one volt per ampere. The unit honors Georg Ohm, the German physicist who showed that current through a wire is proportional to the voltage across it.

Real components span an enormous range. Thick power cables have thousandths of an ohm, resistors in electronics are commonly between a few ohms and a few megohms (MΩ, millions of ohms), and good insulators reach billions of ohms or more. Small resistors carry colored bands that encode their value, and our resistor color code calculator decodes them for you.

Four-band resistor color code diagram for a 470 ohm resistor with 5 percent tolerance
Colored bands encode a resistor's value; these four bands mark 470 Ω with a 5 percent tolerance.

What Factors Affect the Resistance of a Wire?

For a uniform wire, four things set the resistance, and three of them appear in the formula R=ρLA:

  • Length (L): resistance is proportional to length. Double the length and you double the resistance, because electrons face twice as many obstacles.
  • Cross-sectional area (A): resistance is inversely proportional to area. A wire with twice the cross-section has half the resistance, since there are twice as many parallel paths.
  • Material (ρ): resistivity, ρ, measured in ohm meters, is a property of the substance itself. Silver and copper have the lowest values of common metals.
  • Temperature: for metals, resistance rises as the wire gets hotter. This is covered in its own section below.

Our resistivity and conductivity page explains the material property in depth. The table below shows how strongly area affects the resistance of a 10 m copper wire.

Example 2 Resistance of a copper extension cord

One conductor in an extension cord is 20 m of copper wire with a cross-sectional area of 2.5 mm² (2.5 × 10⁻⁶ m²). Taking copper's resistivity as about 1.7 × 10⁻⁸ Ω·m, what is the resistance of that conductor?

  1. Given:
    • resistivity of the material: ρ=1.7×10−8 Ω·m
    • length of the conductor: L=20 m
    • cross-sectional area: A=2.5×10−6 m2
  2. Formula: R=ρLA
  3. Substitute: ρ=1.7×10−8 Ω·m,L=20 m,A=2.5×10−6 m2
  4. Answer: R=0.136 Ω

A small fraction of an ohm, but at high currents even this causes the cord to warm noticeably.

Resistance of a 10 m copper wire with different cross-sectional areas
Cross-sectional area (mm²)Resistance of 10 m (Ω)Typical use
0.50.340Small electronics and signal leads
0.750.227Lamp cords
1.50.113Lighting circuits
2.50.068Wall socket circuits
40.0425Heavy appliances
Source: Computed with R = ρL/A using a typical copper resistivity of about 1.7 × 10⁻⁸ Ω·m at room temperature; uses are typical · Retrieved October 2026

Which Materials Have High and Low Resistance?

Materials fall into broad groups by resistivity. Conductors such as silver, copper, gold and aluminum have plenty of free electrons and very low resistivity, which is why wiring is made from copper or aluminum. Alloys such as nichrome have much higher resistivity and stay stable when hot, so they are used for heating elements.

Insulators such as glass, rubber and most plastics have resistivities trillions of times larger than copper, so they are used to coat wires and to hold live parts safely. In between sit semiconductors like silicon, whose resistance can be tuned by adding impurities or by shining light on them. This tunability is the basis of all modern electronics.

Approximate resistivity of common materials at room temperature
MaterialTypeApproximate resistivity (Ω·m)
SilverConductorabout 1.6 × 10⁻⁸
CopperConductorabout 1.7 × 10⁻⁸
AluminumConductorabout 2.8 × 10⁻⁸
TungstenConductorabout 5.6 × 10⁻⁸
NichromeAlloy for heatersabout 1.1 × 10⁻⁶
Pure siliconSemiconductorroughly 10³ (varies widely)
GlassInsulatorroughly 10¹⁰ to 10¹⁴
Hard rubberInsulatorroughly 10¹³
Source: Typical order-of-magnitude values; real samples vary with purity and temperature · Retrieved October 2026
Copper cables of different thicknesses with plastic insulation, showing low-resistance conductors and high-resistance insulators
Copper cores carry current easily, while the plastic around them has enormous resistance.

How Does Temperature Affect Resistance?

In metals, heating makes the atoms vibrate more strongly, so the drifting electrons collide more often and resistance goes up. Over moderate ranges this is described by R=R0(1+αΔT), where R0 is the resistance at a reference temperature and α is the temperature coefficient of the material.

The effect can be large. A tungsten lamp filament has many times more resistance when glowing than when cold, which is why bulbs most often fail at the moment they are switched on. Some materials behave the other way: semiconductors and the sensors called thermistors lose resistance as they warm up, which makes them useful as electronic thermometers.

At the opposite extreme, certain materials cooled to very low temperatures lose all resistance. These superconductors can carry current with no heating at all and are used in MRI scanners and particle accelerators.

Example 3 A light bulb filament heating up

A tungsten filament has a resistance of 24 Ω at room temperature. Using a typical temperature coefficient of 0.0045 per kelvin, estimate its resistance when it is 2,000 K hotter.

  1. Given:
    • resistance at the reference temperature (usually 20 °C): R0=24 Ω
    • temperature coefficient of resistivity: α=0.0045 1/K
    • temperature change: ΔT=2,000 K
  2. Formula: R=R0(1+αΔT)
  3. Substitute: R0=24 Ω,α=0.0045 1/K,ΔT=2,000 K
  4. Answer: R=240 Ω

The linear formula is only an estimate over such a large range, but it shows why a cold bulb draws a surge of current at switch-on.

How Do Resistances Combine in a Circuit?

When resistances are connected end to end in series, the current must pass through each in turn, so their values simply add: Rs=R1+R2+…. The diagram below shows a 10 Ω and a 20 Ω resistor in series, which act like a single 30 Ω resistor.

When resistances are connected side by side in parallel, the current has several paths, and the total is smaller than the smallest single resistance. For two parallel resistors, 1/Rp=1/R1+1/R2. That is why adding more appliances to a household circuit lowers the overall resistance and raises the total current. Our page on resistors in series and parallel has the full rules, and the series and parallel resistor calculator does the arithmetic for you.

Series circuit with a 12 V battery and resistors of 10 and 20 ohms, whose resistances add to a 30 ohm total
Resistors in series add: 10 Ω plus 20 Ω behaves like a single 30 Ω resistor.

Where Is Resistance Useful in Everyday Life?

Resistance is often treated as a nuisance, but many devices depend on it. Toasters, hair dryers, electric blankets and kettles all work by sending current through a resistive element so that it heats up. Old-style incandescent bulbs heat a thin filament until it glows.

In electronics, components called resistors are added on purpose to limit current, to protect LEDs from burning out and to divide voltages between parts of a circuit. A fuse is a short strip of metal designed to heat and melt when the current is too large, cutting off the power before the wiring overheats. Even a dimmer knob or a volume control is a variable resistance in disguise.

Why Does Resistance Produce Heat?

Every collision between a drifting electron and an atom transfers a little energy to the metal, raising its temperature. The rate at which electrical energy turns into heat in a resistance is P=I2R, which you can explore on our electric power page.

Because the current is squared, heating rises quickly with current. This is why undersized extension cords get warm under heavy loads, and why power companies send electricity over long distances at high voltage and low current. Reducing the current is a far more effective way to cut losses than reducing the resistance of the cable.

Practice Resistance Problems

Work through a few problems to make the formulas second nature. Our Ohm's law worksheets include printable sets on voltage, current and resistance with answer keys. For circuits with several components, compare the layouts in series vs parallel circuits, then try the quiz below.

Common Misconceptions

Myth: Resistance uses up current, so less current comes out of a resistor than goes in.

Physics: Current is the same entering and leaving a resistor. What the resistor removes is energy, which leaves as heat.

Myth: A thicker wire has more resistance because it contains more metal.

Physics: A thicker wire has less resistance, because its larger cross-section gives the electrons more room to flow side by side.

Myth: Resistance and resistivity are the same thing.

Physics: Resistivity belongs to the material alone. Resistance also depends on the length and thickness of the particular object.

Myth: Adding more resistors to a circuit always increases the total resistance.

Physics: That is only true in series. Adding a resistor in parallel opens a new path and lowers the total resistance.

Key Facts

  • Electrical resistance measures how strongly an object opposes current, defined by R = V / I.
  • The SI unit of resistance is the ohm (Ω), equal to one volt per ampere.
  • For a uniform wire, R = ρL / A, so resistance grows with length and falls with cross-sectional area.
  • Resistivity is a property of the material, while resistance depends on the material and the shape of the object.
  • The resistance of a metal rises as it heats up, while that of a semiconductor usually falls.
  • Resistances in series add directly; in parallel the total is less than the smallest one.
  • Current through a resistance produces heat at a rate of P = I²R.
Did you know? Copper wire used in homes is so pure for a reason: even a fraction of a percent of some impurities can raise its resistivity noticeably, wasting energy as heat in every meter of cable.

Quick Quiz: How Well Do You Know Electrical Resistance?

6 questions. Tap an answer to check it.

  1. Which formula defines electrical resistance?

  2. What happens to the resistance of a wire if its length is doubled?

  3. What happens to the resistance of a wire if its cross-sectional area is doubled?

  4. Which of these has the lowest resistivity?

  5. How does the resistance of a metal wire change as it gets hotter?

  6. A 12 Ω and a 6 Ω resistor are connected in series. What is the total resistance?

Frequently Asked Questions

What is electrical resistance in simple words?

Electrical resistance is how much a material or object fights against the flow of electric current. With the same battery, a high-resistance object lets only a small current through, while a low-resistance object lets a large current through. Copper wires have very low resistance, while rubber and plastic have extremely high resistance. Resistance also turns some electrical energy into heat.

What is the SI unit of resistance?

Resistance is measured in ohms, written with the Greek letter Ω. One ohm is the resistance that allows one ampere of current to flow when one volt is applied, so 1 Ω = 1 V/A. Larger values use kilohms (kΩ, thousands of ohms) and megohms (MΩ, millions of ohms), which are common on electronic resistors.

What is the formula for electrical resistance?

The defining formula is R = V / I, where V is the voltage across the object in volts and I is the current through it in amperes. For a uniform wire you can also calculate resistance from its shape and material with R = ρL / A, where ρ is resistivity in ohm meters, L is length in meters and A is cross-sectional area in square meters.

What are the four factors that affect resistance?

The four factors are the material, the length, the cross-sectional area and the temperature. Resistance increases with length, decreases as the wire gets thicker, depends on the resistivity of the material and, for metals, rises as the temperature goes up. The first three are combined in the formula R = ρL / A, and temperature changes the value of ρ.

Why does resistance increase with temperature in metals?

When a metal gets hotter, its atoms vibrate more strongly about their positions. The free electrons that carry current collide with these vibrating atoms more often, which makes it harder for them to drift along the wire. More collisions mean more resistance. In semiconductors the effect is usually reversed, because heating frees extra charge carriers that make conduction easier.

What is the difference between resistance and resistivity?

Resistivity is a property of a material, telling you how strongly that substance opposes current regardless of shape. Resistance is a property of a particular object and depends on both its material and its dimensions. Two copper wires share the same resistivity, but a long thin one has much more resistance than a short thick one. Resistivity is measured in ohm meters, resistance in ohms.

Does a thicker wire have more or less resistance?

A thicker wire has less resistance. Its larger cross-sectional area gives the moving electrons more parallel paths, so the same voltage drives a larger current. Resistance is inversely proportional to area, so doubling the area halves the resistance. This is why high-current circuits, such as those for ovens and car chargers, use thicker cable than lighting circuits.

Can resistance ever be zero?

Ordinary conductors always have some resistance, even very good ones like silver and copper. Superconductors are the exception: when cooled below a critical temperature, certain materials lose all electrical resistance and can carry current without any heating. This effect is used in powerful magnets for MRI machines and particle accelerators, but it requires very cold conditions to maintain.

How do you measure electrical resistance?

The simplest way is with a multimeter set to its ohms range, with the component disconnected from any power source. The meter sends a small known current through the part and reports the resistance. You can also measure the voltage across a component and the current through it while it operates, then divide the voltage by the current using R = V / I.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.