Push, flow and power

Volts vs Amps vs Watts

Volts, amps and watts measure three different things: volts measure voltage, the electrical push that drives charge around a circuit; amps measure current, the rate at which charge flows; and watts measure power, the rate at which energy is delivered. The three are linked by one simple rule, watts equal volts times amps, so knowing any two lets you find the third.

Multimeter test leads connected to a glowing light bulb on a workbench, measuring the voltage and current that set its power
A glowing bulb needs both a voltage to push charge and a current of charge flowing; together they set its power in watts.

At a Glance

Voltage (V, in volts) is the energy each coulomb of charge carries, current (I, in amperes) is how much charge passes per second, and power (P, in watts) is the energy delivered per second. They are linked by P = I × V, and voltage and current are linked through resistance by Ohm's law, V = I × R.

Volt (V)
Unit of voltage: 1 V = 1 J per coulomb
Ampere (A)
Unit of current: 1 A = 1 coulomb per second
Watt (W)
Unit of power: 1 W = 1 J per second
Linking formula
P = I × V (watts = amps × volts)
Ohm's law
V = I × R, with R in ohms
Energy on your bill
kilowatt-hours = kilowatts × hours
On this page
  1. What Is the Difference Between Volts, Amps and Watts?
  2. What Do Volts, Amps and Watts Measure?
  3. How Do You Convert Between Volts, Amps and Watts?
  4. How Does Resistance Connect Voltage and Current?
  5. What Are Typical Volts, Amps and Watts at Home?
  6. What Is the Difference Between Watts and Watt-Hours?
  7. Is It the Volts or the Amps That Are Dangerous?
  8. Who Are Volts, Amps and Watts Named After?
  9. Common Misconceptions
  10. Key Facts
  11. Quiz
  12. FAQ

What Is the Difference Between Volts, Amps and Watts?

Each unit answers a different question about the same circuit. Volts answer "how hard is the charge being pushed?" Amps answer "how much charge flows past a point each second?" Watts answer "how much energy is being delivered each second?"

A common analogy uses a garden hose. Voltage is like the water pressure at the tap, current is like the amount of water flowing through the hose each second, and power is like the work that stream can do, such as spinning a small water wheel. High pressure with almost no flow does little work, and so does a big flow with almost no pressure. You need both.

The analogy is not perfect, since charge is not used up the way water drains away, but it captures the key idea: watts depend on volts and amps together. The table below compares the three units point by point.

Volts, amps and watts compared side by side
FeatureVolts (V)Amps (A)Watts (W)
Quantity measuredVoltage (potential difference)Electric currentPower
Usual symbolVIP
What it describesEnergy per unit chargeCharge flow per secondEnergy delivered per second
Definition in other units1 V = 1 J/C1 A = 1 C/s1 W = 1 J/s = 1 V × 1 A
SI base unitskg m² s⁻³ A⁻¹A (SI base unit)kg m² s⁻³
Hose analogyWater pressureFlow rateWork done by the stream
Formula to find itV = P / I or V = I RI = P / V or I = V / RP = I V
Measured withVoltmeter, across a partAmmeter, in seriesWattmeter or power meter
Set mainly byThe power sourceThe source and the load's resistanceBoth voltage and current
Typical household value (US)About 120 V15 A circuit limitAbout 1,800 W per 15 A circuit
On an appliance labelRated voltageRated currentRated power
Named afterAlessandro VoltaAndré-Marie AmpèreJames Watt
Source: Unit definitions and base-unit expressions from the BIPM SI Brochure (data/si-units.json); 1,800 W computed as 120 V × 15 A; household values are typical · Retrieved October 2026

What Do Volts, Amps and Watts Measure?

Voltage, also called potential difference, is the energy given to each coulomb of charge as it moves between two points. Its unit is the volt: one volt means one joule of energy per coulomb. A 9 V battery gives every coulomb that passes through it 9 J of energy to spend in the circuit.

Electric current is the rate at which charge flows. Its unit is the ampere, or amp: one amp means one coulomb passing a point every second. In a metal wire that charge is carried by electrons, and an ammeter wired into the circuit measures how many pass by.

Electric power is the rate at which electrical energy is converted into light, heat, motion or sound. Its unit is the watt: one watt is one joule per second. A 10 W LED lamp turns 10 J of electrical energy into light and a little heat every second.

How Do You Convert Between Volts, Amps and Watts?

The bridge between the three is the power formula, P=IV. Multiply amps by volts to get watts. Divide watts by volts to get amps, I=P/V. Divide watts by amps to get volts, V=P/I.

The units check out neatly. A volt is a joule per coulomb and an amp is a coulomb per second, so volts times amps gives joules per second, which is exactly a watt. That is also why you cannot convert volts directly into watts on their own: you always need the current as well.

The worked examples below use everyday devices. To try your own numbers, use our electrical power calculator.

Here is the electric power formula with each variable and its SI unit, plus its rearranged forms for current and voltage.

P=IV
What each symbol means
SymbolQuantitySI unit
Ppowerwatt (W)
Icurrentampere (A)
Vvoltagevolt (V)

Rearranged to find another variable:

I=PVV=PI

Valid for: for AC use rms values.

Example 1 How many amps does a space heater draw?

A space heater is rated at 1,500 W and plugs into a 120 V household outlet. How much current does it draw?

  1. Given:
    • power: P=1,500 W
    • voltage: V=120 V
  2. Formula: I=PV
  3. Substitute: I=(1,500 W)(120 V)
  4. Answer: I=12.5 A

That is a large share of a typical 15 A household circuit, which is why heaters often trip breakers when shared with other appliances.

Example 2 Power of a phone charger

A phone charger delivers 2 A at 5 V through a USB cable. How much power does it supply?

  1. Given:
    • current: I=2 A
    • voltage: V=5 V
  2. Formula: P=IV
  3. Substitute: P=(2 A)(5 V)
  4. Answer: P=10 W

Fast chargers deliver more power by raising the voltage, the current or both once the phone agrees to it.

How Does Resistance Connect Voltage and Current?

Power links all three units, but it does not tell you how much current a given voltage will push. That depends on the resistance of the device, measured in ohms. Ohm's law, V=IR, says that for many conductors the current is proportional to the voltage, with resistance as the constant of proportion.

Combine Ohm's law with P=IV and you get two more handy forms: P=I2R and P=V2/R. The second one explains why the same appliance draws less power on a lower voltage: halve the voltage across a fixed resistance and the power drops to a quarter.

For problems that start from resistance, our Ohm's law calculator solves for any of the three values.

Example 3 Current through a car headlight filament

A car headlight filament has a resistance of 4 Ω when lit and is connected across a 12 V battery. What current flows through it?

  1. Given:
    • voltage across the resistor: V=12 V
    • resistance: R=4 Ω
  2. Formula: I=VR
  3. Substitute: I=(12 V)(4 Ω)
  4. Answer: I=3 A

Multiply this current by the 12 V supply and you get the lamp's power, about 36 W (computed).

Series circuit with a 12 V battery, a 4 ohm resistor, an ammeter in series and a voltmeter across the resistor
The voltmeter reads the push across the resistor, the ammeter reads the current through it, and their product is the power.

What Are Typical Volts, Amps and Watts at Home?

Everyday devices span a wide range. An AA battery supplies about 1.5 V, a USB port about 5 V and a car battery about 12 V. A wall outlet in the United States provides about 120 V, while much of Europe, Asia and Africa uses about 230 V.

Currents vary just as much. A modern 9 W LED bulb on a 120 V circuit draws only 0.075 A (computed), while an old 60 W incandescent bulb draws 0.5 A (computed). A typical household circuit is protected at 15 A, so it can deliver about 1,800 W (computed as 120 V × 15 A) before the breaker trips.

The table of typical values below gathers these numbers together. Treat them as approximate, since real devices vary with design and load.

Typical voltage, current and power of everyday devices
DeviceVoltageCurrentPower
LED bulb on a US outlet120 V0.075 A9 W
Incandescent bulb on a US outlet120 V0.5 A60 W
USB phone charger5 V2 A10 W
Car headlight filament12 V3 A36 W
Space heater on a US outlet120 V12.5 A1,500 W
Electric kettle on a 230 V outlet230 Vabout 8.7 A2,000 W
Source: Voltages and power ratings are typical values; currents computed with I = P / V (data/formulas.json) · Retrieved October 2026

What Is the Difference Between Watts and Watt-Hours?

Watts measure a rate, while watt-hours measure an amount of energy. Running a 1,000 W heater for one hour uses 1,000 Wh, or 1 kilowatt-hour, the unit on electricity bills. Running the same heater for 30 minutes uses half that.

Battery packs follow the same logic. A power bank labeled in watt-hours tells you its stored energy, and dividing by the power of a device estimates how long it will run. A 36 Wh pack (computed as 10,000 mAh at 3.6 V) can in principle run a 9 W lamp for about four hours, minus conversion losses.

Utilities charge for energy, not power, so the same appliance costs more the longer it runs. If you want the energy idea in more depth, see energy vs power.

Is It the Volts or the Amps That Are Dangerous?

The harm from an electric shock comes from current flowing through the body, so in that sense amps are what hurt. But current does not flow on its own: a voltage has to push it through your skin's resistance. A higher voltage can drive a larger current through the same body, which is why high-voltage lines are so hazardous.

A car battery can deliver hundreds of amps to a starter motor, yet touching both terminals with dry hands is usually harmless, because 12 V cannot push much current through skin. A wall outlet at 120 V or 230 V can. Never test this, and follow the rules on our electrical safety page.

Who Are Volts, Amps and Watts Named After?

Each unit honors a pioneer. The volt is named for Alessandro Volta, who built the voltaic pile, the first electric battery. The ampere honors André-Marie Ampère, a founder of electrodynamics. The watt is named for James Watt, whose improved steam engine made power a key engineering quantity.

To practice switching between the three, try our Ohm's law worksheets, then take the quiz below. For a closer look at just the first two units, see current vs voltage.

Common Misconceptions

Myth: Volts and watts are the same thing.

Physics: Volts measure the push on each unit of charge, while watts measure energy delivered per second. Watts equal volts times amps, so you need the current to get from one to the other.

Myth: A power supply forces its full current rating into any device.

Physics: The voltage is fixed by the supply, but the current is set by what the device draws. A 3 A charger connected to a phone that needs 1 A delivers only about 1 A.

Myth: Higher voltage always means more power.

Physics: Power depends on voltage and current together. A static shock can reach thousands of volts but lasts so briefly with so little charge that the energy involved is tiny.

Myth: Current gets used up as it flows through a bulb.

Physics: The current entering a bulb equals the current leaving it. What the bulb uses is energy, which the charge carries in and gives up as light and heat.

Key Facts

  • Volts measure voltage, the energy each coulomb of charge carries between two points.
  • Amps measure current, the amount of charge passing a point each second.
  • Watts measure power, the electrical energy delivered each second.
  • Power equals current times voltage: P = I × V.
  • Ohm's law, V = I × R, links voltage and current through resistance.
  • Electricity bills charge for energy in kilowatt-hours, not for power in watts.
  • Shocks are caused by current through the body, but voltage is what drives that current.
Did you know? Long-distance power lines run at hundreds of thousands of volts so that they can carry the same power with a much smaller current, because the energy wasted as heat in the wires grows with the square of the current.

Quick Quiz: How Well Do You Know Voltage vs Amps?

6 questions. Tap an answer to check it.

  1. Which unit measures the rate at which electrical energy is delivered?

  2. A toaster draws 7 A from a 120 V outlet. What is its power?

  3. What does one ampere mean?

  4. A 60 W lamp runs on 120 V. How much current does it draw?

  5. Which law links voltage, current and resistance?

  6. What does an electricity bill charge you for?

Frequently Asked Questions

What is the difference between voltage and amps?

Voltage is the electrical push, measured in volts, that drives charge around a circuit. Amps measure the current, the amount of charge flowing past a point each second. Voltage is the cause and current is the result, and the amount of current a given voltage produces depends on the resistance of the circuit, as described by Ohm's law, V = I × R.

What is the difference between voltage and wattage?

Voltage is the energy each coulomb of charge carries, measured in volts. Wattage is power, the total energy delivered per second, measured in watts. Wattage depends on voltage and current together, P = I × V. Two devices on the same 120 V outlet can have very different wattages because they draw different currents, such as a 9 W LED bulb and a 1,500 W heater.

How do you convert amps to watts?

Multiply the current in amps by the voltage in volts: watts = amps × volts. For example, a device drawing 3 A from a 12 V supply uses 36 W. You cannot convert amps to watts without knowing the voltage, because the same current delivers more power when pushed by a higher voltage. For AC appliances this simple product gives the apparent power.

How do you convert watts to amps?

Divide the power in watts by the voltage in volts: amps = watts ÷ volts. A 1,200 W microwave on a 120 V outlet draws about 10 A. The same rule tells you how many devices can share a circuit: add up their currents and keep the total below the breaker's rating, which is often 15 A or 20 A in homes.

Is it volts or amps that kill?

The direct cause of injury is current flowing through the body, especially through the heart. However, current only flows if a voltage pushes it through the body's resistance, and dry skin resists a lot. That is why low-voltage sources like a 12 V car battery are usually safe to touch, while household and high-voltage lines can drive a deadly current.

What does 1 watt equal in volts and amps?

One watt equals one volt multiplied by one ampere. In energy terms it is one joule per second. So a device at 1 V drawing 1 A uses 1 W, and so does a device at 10 V drawing 0.1 A. Many combinations of voltage and current give the same power, which is why fast chargers can trade one for the other.

Why do appliances list volts, amps and watts?

Each number tells you something different. The voltage tells you which outlet or supply the appliance needs. The current tells you how much load it puts on the circuit and how thick the wiring must be. The wattage tells you how much power it uses, which, multiplied by running time, sets how much energy you pay for.

What is the difference between watts and kilowatt-hours?

Watts measure power, the rate of energy use at a given moment. Kilowatt-hours measure energy, the total used over time. A 2,000 W heater running for 3 hours uses 6 kWh. Electricity companies bill you for kilowatt-hours, so a low-wattage device left on all day can cost more than a high-wattage one used for a few minutes.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.