Measurement in physics

Accuracy vs Precision

Accuracy describes how close a measurement is to the true or accepted value, while precision describes how close repeated measurements are to one another. A result can be precise without being accurate, as when every reading lands in a tight cluster that sits off target. Physicists judge accuracy with percent error and precision with the spread of repeated readings.

Five arrows grouped tightly together but away from the center of an archery target, a picture of precision without accuracy
A tight group away from the center is precise but not accurate, the pattern a systematic error leaves in lab data.

At a Glance

Accuracy is closeness to the true value, usually measured with percent error = |measured − accepted| / accepted × 100%. Precision is closeness of repeated readings to each other, measured by their spread, such as half the range or the standard deviation. Systematic errors spoil accuracy, while random errors spoil precision.

Accuracy
How close a result is to the true value
Precision
How close repeated results are to each other
Accuracy measured by
Percent error (needs an accepted value)
Precision measured by
Spread: range, half-range or standard deviation
Spoiled by
Accuracy: systematic error · Precision: random error
On this page
  1. What Is the Difference Between Accuracy and Precision?
  2. How Are Accuracy and Precision Defined?
  3. What Does the Target Analogy Show?
  4. How Do You Measure Accuracy and Precision?
  5. Which Is Better: Accurate or Precise Results?
  6. How Do Systematic and Random Errors Affect Accuracy and Precision?
  7. What Are Real-Life Examples of Accuracy and Precision?
  8. How Can You Practice Telling Them Apart?
  9. Common Misconceptions
  10. Key Facts
  11. Quiz
  12. FAQ

What Is the Difference Between Accuracy and Precision?

Accuracy and precision are both words about the quality of a measurement, and in everyday speech they are often swapped. In science they mean different things. Accuracy asks: did we get close to the right answer? Precision asks: if we repeat the measurement, do we get the same answer again?

The two are independent. Readings can be accurate and precise, precise but inaccurate, accurate on average but imprecise, or neither. Accuracy needs a reference, a true or accepted value to compare with. Precision needs only the readings themselves, because it is about how much they scatter.

The table below sets the two side by side. Both ideas belong to the wider topic of measurement in physics, where every reported number carries some doubt.

Accuracy and precision compared side by side
FeatureAccuracyPrecision
Question it answersIs the result close to the true value?Do repeated results agree with each other?
Needs a true or accepted value?YesNo
Can be judged from one reading?Yes, if the accepted value is knownNo, needs repeated readings
Common measurePercent errorRange, half-range or standard deviation
Formula|x_exp − x_acc| / |x_acc| × 100%(x_max − x_min) / 2, or as a % of the mean
Mainly reduced bySystematic errorsRandom errors
Improved byCalibration against a standardRepeating, averaging, finer instruments
Does averaging help?Not against systematic errorYes, the mean becomes more precise
Shown in the number asHow near the value is to the referenceNumber of significant figures and the ± value
Target analogyArrows centered on the bullseyeArrows grouped tightly together
Graph appearancePoints centered on the true linePoints close to each other
Everyday exampleA scale that shows your true weightA scale that shows the same weight every time
Source: Definitions as used in school and laboratory physics; example values are illustrative · Retrieved October 2026

How Are Accuracy and Precision Defined?

A measurement is accurate when its value lies close to the quantity's true value. Since the true value is rarely known perfectly, physicists compare with an accepted value instead: a standard such as 9.80665 m/s² for standard gravity, or a careful result from a better instrument.

A set of measurements is precise when the readings agree closely with each other. Precision also describes an instrument's fineness: a digital caliper reading to 0.01 mm can report more precise lengths than a school ruler marked in millimeters. That second meaning is tied to significant figures, since the number of digits you write signals how precise the reading is.

International measurement standards use the word trueness for the closeness of an average to the true value and keep accuracy for single results, which combine trueness and precision. In school and most lab work, the simpler definitions above are used.

What Does the Target Analogy Show?

Picture four archers each shooting five arrows at a target. Their patterns show the four combinations:

  • Accurate and precise: all five arrows cluster tightly in the center.
  • Precise, not accurate: the arrows cluster tightly, but in one spot away from the center.
  • Accurate, not precise: the arrows are scattered widely, yet their average position is the center.
  • Neither: the arrows are scattered and their average sits off center.

The second case is the most dangerous in a lab, because tight agreement looks convincing. A bow sight bent a little to one side gives a beautiful cluster in the wrong place, just as a miscalibrated instrument gives consistent wrong readings.

How Do You Measure Accuracy and Precision?

Accuracy is measured with percent error: %error=|xexp−xacc|/|xacc|×100%. A smaller percent error means a more accurate result. You need an accepted value to use it.

Precision is measured from the spread of repeated readings. The quickest estimate is half the range, (xmax−xmin)/2, often quoted as a percent of the mean, which is the percent uncertainty. With more data, scientists use the standard deviation. A smaller spread means higher precision, and no accepted value is needed.

The worked examples below apply both measures to two students who measured the same quantity, the acceleration due to gravity, with different methods.

Accuracy is usually reported as a percent error, which compares a measured value with the accepted one.

%error=|xexp−xacc||xacc|×100%
What each symbol means
SymbolQuantitySI unit
%errorpercent errordimensionless (1)
xexpexperimental (measured) valuedimensionless (1)
xaccaccepted (true) valuedimensionless (1)

Valid for: x_exp and x_acc must be in the same units (any unit); the result is dimensionless.

Example 1 Student A: scattered readings of g

Student A times a dropped ball five times and calculates g as 9.6, 10.1, 9.9, 9.5 and 10.0 m/s². Taking 9.81 m/s² as the local accepted value, what is the percent error of the average?

  1. Given:
    • reading 1: x1=9.6 m/s2
    • reading 2: x2=10.1 m/s2
    • reading 3: x3=9.9 m/s2
    • reading 4: x4=9.5 m/s2
    • reading 5: x5=10 m/s2
    • accepted (true) value: xacc=9.81 m/s2
  2. Formula: %error=|x¯−xacc|xacc×100%,x¯=x1+x2+x3+x4+x55
  3. Substitute: x1=9.6 m/s2,x2=10.1 m/s2,x3=9.9 m/s2,x4=9.5 m/s2,x5=10 m/s2,xacc=9.81 m/s2
  4. Answer: %error=0.1019 %

The average of 9.82 m/s² lands almost on target, so Student A is accurate even though single readings differ by up to 0.6 m/s².

Example 2 Student B: tight readings that miss

Student B uses light gates and gets 9.71, 9.73, 9.72, 9.70 and 9.74 m/s². With the same accepted value of 9.81 m/s², what is the percent error of the average?

  1. Given:
    • reading 1: x1=9.71 m/s2
    • reading 2: x2=9.73 m/s2
    • reading 3: x3=9.72 m/s2
    • reading 4: x4=9.7 m/s2
    • reading 5: x5=9.74 m/s2
    • accepted (true) value: xacc=9.81 m/s2
  2. Formula: %error=|x¯−xacc|xacc×100%,x¯=x1+x2+x3+x4+x55
  3. Substitute: x1=9.71 m/s2,x2=9.73 m/s2,x3=9.72 m/s2,x4=9.7 m/s2,x5=9.74 m/s2,xacc=9.81 m/s2
  4. Answer: %error=0.9174 %

Student B's error is about nine times larger than Student A's, even though B's readings agree with each other far better.

Which Is Better: Accurate or Precise Results?

Student A's readings swing between 9.5 and 10.1 m/s², yet their average is 9.82 m/s², only about 0.10% from the accepted 9.81 m/s². Student B's readings agree to within 0.04 m/s², but their average of 9.72 m/s² is about 0.92% low (all computed). A is more accurate; B is more precise.

Neither alone is enough. Precise but inaccurate data hide a flaw that more repeats will never reveal, while accurate but imprecise data need many repeats before the average can be trusted. The graph shows the same pattern for two sensors logging g on a lab bench: one wanders widely around the truth, the other sits steady but low.

The best results are both. Improve precision by reducing random scatter, then check accuracy against a known standard.

Example 3 Comparing the spread: Student A's precision

Precision can be expressed as half the range of the readings divided by their mean. For Student A's readings of 9.6, 10.1, 9.9, 9.5 and 10.0 m/s², what is this percent spread?

  1. Given:
    • reading 1: x1=9.6 m/s2
    • reading 2: x2=10.1 m/s2
    • reading 3: x3=9.9 m/s2
    • reading 4: x4=9.5 m/s2
    • reading 5: x5=10 m/s2
  2. Formula: %unc=(xmax−xmin)/2x¯×100%
  3. Substitute: x1=9.6 m/s2,x2=10.1 m/s2,x3=9.9 m/s2,x4=9.5 m/s2,x5=10 m/s2
  4. Answer: %unc=3.055 %

The same calculation for Student B gives about 0.21% (computed), roughly fifteen times tighter: B is more precise, A is more accurate.

Two students measure g five times: accuracy versus precision
StudentReadings (m/s²)Mean (m/s²)Percent errorHalf-range (m/s²)Verdict
A (stopwatch)9.6, 10.1, 9.9, 9.5, 10.09.820.10%0.30Accurate, not precise
B (light gates)9.71, 9.73, 9.72, 9.70, 9.749.720.92%0.02Precise, not accurate
Source: Invented example readings; means, percent errors and half-ranges computed against an accepted local value of 9.81 m/s² · Retrieved October 2026
Graph of two sensors measuring g: one swings widely around the true value, the other stays steady but below it
Wide swings centered on the truth mean accurate but imprecise; a steady line below it means precise but inaccurate.

How Do Systematic and Random Errors Affect Accuracy and Precision?

Systematic errors push every reading the same way: a scale that reads 3 g too high, a ruler with a worn end, a thermometer read before it settles. They shift the whole cluster, so they damage accuracy while leaving precision untouched. Averaging does not remove them; calibration does.

Random errors push readings up or down unpredictably: reaction time on a stopwatch, a draft on a balance, electrical noise. They widen the cluster and damage precision. Taking more readings and averaging shrinks their effect on the mean.

The full story, with ways to find and fix each kind, is on our page about systematic and random errors. A classic systematic error is a zero error, where an instrument does not read zero when it should.

What Are Real-Life Examples of Accuracy and Precision?

  • Bathroom scale: if it shows 71.4 kg every time for a person whose true mass is 70.0 kg, it is precise but inaccurate. A quick check with a known weight reveals the offset.
  • Kitchen oven: a dial set to 180 °C that actually holds 195 °C every time is precise but inaccurate; one that swings between 170 °C and 190 °C is imprecise.
  • GPS on a phone: a fix that jumps around by several meters while standing still is imprecise, even if it averages to the right spot.
  • Pendulum lab: timing 20 swings and dividing by 20 makes the period more precise, because reaction-time error is spread over many swings. See our pendulum period lab.

In each case, ask two separate questions: do repeated readings agree, and do they agree with the truth?

How Can You Practice Telling Them Apart?

Collect five repeated readings of anything, a ruler drop time or the length of a desk, and work out both the percent spread and, where you know the true value, the percent error. Our measuring g by free fall experiment is an ideal test, since the accepted value is well known. The ruler drop reaction time activity shows random error in action, and the quiz below checks the key ideas.

Common Misconceptions

Myth: Accuracy and precision mean the same thing.

Physics: Accuracy compares a result with the true value; precision compares repeated results with each other. Readings can have one quality without the other.

Myth: If my readings agree closely, my answer must be correct.

Physics: Close agreement shows precision only. A systematic error, such as an uncalibrated instrument, can shift every reading by the same amount.

Myth: Writing more decimal places makes a result more accurate.

Physics: Extra digits only claim more precision, and they are justified only if the instrument and method support them. They say nothing about closeness to the true value.

Myth: Taking more measurements always fixes an inaccurate result.

Physics: Averaging shrinks random error, which improves precision of the mean. A systematic error stays in every reading and in the average, so only calibration or a better method removes it.

Key Facts

  • Accuracy is how close a measurement is to the true or accepted value.
  • Precision is how close repeated measurements are to each other.
  • A set of readings can be precise without being accurate, and accurate on average without being precise.
  • Accuracy is usually expressed as percent error, which requires an accepted value.
  • Precision is expressed as a spread, such as half the range or the standard deviation of repeated readings.
  • Systematic errors reduce accuracy; random errors reduce precision.
  • Averaging many readings improves precision but cannot fix a systematic error.
Did you know? Since 2019 all seven SI base units have been defined by fixing exact values of constants such as the speed of light and the Planck constant, so the ultimate reference for accuracy is now built into nature itself rather than kept in a vault.

Quick Quiz: How Well Do You Know Accuracy vs Precision?

6 questions. Tap an answer to check it.

  1. Which word describes how close a measurement is to the true value?

  2. Five readings of a length are 12.31, 12.30, 12.32, 12.31 and 12.30 cm, but the true length is 12.80 cm. The readings are:

  3. Which type of error mainly reduces precision?

  4. What does averaging many repeated readings improve?

  5. Which quantity is a measure of accuracy?

  6. A balance reads 0.4 g with nothing on it. What does this zero error mainly affect?

Frequently Asked Questions

What is the difference between accuracy and precision?

Accuracy is how close a measurement comes to the true or accepted value. Precision is how close repeated measurements come to each other. A thermometer that always reads 2 °C too high is precise but not accurate. One that reads the right value on average but jumps around from reading to reading is accurate on average but not precise.

Can a measurement be precise but not accurate?

Yes, and it is common. If an instrument has a systematic error, such as a balance that was not zeroed, every reading is shifted by the same amount. The readings agree closely with each other, so they are precise, but they all miss the true value, so they are not accurate. Calibration against a known standard reveals the problem.

Can a measurement be accurate but not precise?

A set of readings can be scattered widely yet average out close to the true value. That set is accurate on average but not precise. Any single reading from it may be far off, so you need many repeats before trusting the mean. Reducing random error, for example with a better timer, would make the readings precise as well.

How do you calculate accuracy?

Accuracy is usually expressed as percent error. Subtract the accepted value from the measured value, take the absolute value, divide by the accepted value and multiply by 100. A measured g of 9.72 m/s² against 9.81 m/s² gives about 0.92% error. The smaller the percent error, the more accurate the result.

How do you calculate precision?

Take several readings of the same quantity and measure how much they spread. A quick method is half the range: subtract the smallest reading from the largest and divide by two. Dividing that by the mean and multiplying by 100 gives a percent spread. For larger data sets, scientists calculate the standard deviation instead.

Which is more important, accuracy or precision?

Both matter, and they solve different problems. Precision tells you the measurement is repeatable, and accuracy tells you it is right. In practice, scientists first make a method precise so the readings are stable, then calibrate it against a standard so the stable readings are also correct. A result that is only one of the two is not fully trustworthy.

What type of error affects accuracy?

Systematic errors affect accuracy. They shift every reading in the same direction by about the same amount, for example a stretched measuring tape, a clock that runs fast or a parallax error from always reading a scale from one side. Because the shift repeats, averaging does not remove it. Finding and correcting the cause is the only fix.

Do significant figures show accuracy or precision?

Significant figures show precision. Writing 9.720 m/s² instead of 9.7 m/s² claims that the measurement is reliable to the thousandths place. It says nothing about whether the value is close to the true one. A precise-looking number with many digits can still be inaccurate if the instrument has a systematic error.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.