Constant temperature vs no heat flow

Isothermal vs Adiabatic Processes

The difference between an isothermal and an adiabatic process is what is held fixed: in an isothermal process the temperature stays constant because heat flows in or out freely, while in an adiabatic process no heat crosses the boundary, so the temperature changes as the gas does work. For an ideal gas, isothermal changes follow PV = constant and adiabatic changes follow PV^γ = constant.

Two piston cylinders, one in a water bath for constant temperature and one wrapped in insulation so no heat can flow
A water bath keeps a gas at constant temperature (isothermal), while insulation blocks heat flow entirely (adiabatic).

At a Glance

In an isothermal process, ΔT = 0, so the internal energy of an ideal gas does not change and all work is balanced by heat: Q = W, with P1 V1 = P2 V2. In an adiabatic process, Q = 0, so all work changes the internal energy: ΔU = -W, with P1 V1^γ = P2 V2^γ. Isothermal changes are slow with good heat contact; adiabatic changes are fast or insulated.

Isothermal
Temperature constant, ΔT = 0
Adiabatic
No heat exchanged, Q = 0
Ideal gas equation
Isothermal: PV = constant · Adiabatic: PV^γ = constant
First law
Isothermal: Q = W · Adiabatic: ΔU = -W
Typical speed
Isothermal: slow · Adiabatic: fast or insulated
PV curve
Adiabatic curve is steeper than the isotherm
On this page
  1. What Is the Difference Between Isothermal and Adiabatic Processes?
  2. How Does the First Law Apply to Each Process?
  3. What Are the Equations for Isothermal and Adiabatic Processes?
  4. Why Is an Adiabatic Curve Steeper on a PV Diagram?
  5. Does Temperature Change in an Adiabatic Process?
  6. What Are Real Examples of Each Process?
  7. Isothermal vs Adiabatic Explained Simply
  8. Common Misconceptions
  9. Key Facts
  10. Quiz
  11. FAQ

What Is the Difference Between Isothermal and Adiabatic Processes?

Both terms describe how a gas, or any system, changes from one state to another. They differ in what the system is allowed to share with its surroundings.

An isothermal process keeps the temperature constant. To do that, heat must flow freely through the walls: in when the gas expands and does work, out when the gas is compressed. An adiabatic process allows no heat to cross the walls at all, so any work done by or on the gas changes its internal energy and therefore its temperature.

A useful shortcut: isothermal means "same temperature" and adiabatic means "no heat passes". The table below compares them feature by feature.

Isothermal and adiabatic processes compared side by side
FeatureIsothermal processAdiabatic process
What stays fixedTemperature (ΔT = 0)Heat exchanged (Q = 0)
Heat flowFlows in or out freelyNone
TemperatureConstantRises on compression, falls on expansion
Change in internal energy (ideal gas)ΔU = 0ΔU = -W
First law becomesQ = WΔU = -W
Ideal gas equationP V = constantP V^γ = constant
Shape on a PV diagramIsotherm (hyperbola)Steeper curve
Work in expansion between same volumesLargerSmaller
WallsThin and heat-conductingInsulated, or change is very fast
Speed of changeSlowFast
Pressure after halving volumeDoublesMore than doubles
Everyday exampleSlow expansion in a water bathBike pump or diesel compression
Source: Ideal-gas relations from our formula data; γ ≈ 1.4 for air is a typical value · Retrieved October 2026

How Does the First Law Apply to Each Process?

The first law of thermodynamics, ΔU=Q−W, keeps track of energy. For an ideal gas, internal energy depends only on temperature.

In an isothermal process the temperature does not change, so ΔU=0 and Q=W. Every joule of work the gas does is paid for by a joule of heat flowing in from the surroundings.

In an adiabatic process Q=0, so ΔU=−W. When the gas expands and does work, it pays with its own internal energy and cools down. When it is compressed, the work done on it becomes internal energy and it warms up.

What Are the Equations for Isothermal and Adiabatic Processes?

For an ideal gas at constant temperature, Boyle's law applies: P1V1=P2V2. Halve the volume and the pressure doubles. The work done by the gas in an isothermal change is W=nRTln⁡(Vf/Vi).

For a slow adiabatic change, the rule is P1V1γ=P2V2γ, where γ is the ratio of the gas's heat capacities. It is 5/3 for a monatomic gas like helium and about 1.4 for air. Because γ is greater than 1, the pressure changes more sharply than in the isothermal case.

The two examples below compress the same air from the same start to the same final volume, once slowly and once quickly, so you can compare the answers directly. For a calculator built on the ideal gas law, use our ideal gas law calculator.

Here is the adiabatic equation for an ideal gas; the isothermal case is the same equation with the exponent γ replaced by 1.

P1V1γ=P2V2γ
What each symbol means
SymbolQuantitySI unit
P1initial pressurepascal (Pa)
V1initial volumecubic meter (m³)
P2final pressurepascal (Pa)
V2final volumecubic meter (m³)
γheat capacity ratio C_p/C_V (5/3 monatomic, 7/5 diatomic)dimensionless (1)

Rearranged to find another variable:

P2=P1(V1V2)γV2=V1(P1P2)1/γ

Valid for: quasi-static adiabatic (Q = 0) process of an ideal gas.

Example 1 Slowly squeezing a bike pump (isothermal)

A bike pump holds 0.5 L of air at 100,000 Pa. With the outlet blocked, you push the handle very slowly, so the air stays at room temperature, until the volume is 0.2 L. What is the new pressure?

  1. Given:
    • initial pressure: P1=100,000 Pa
    • initial volume: V1=0.5 L
    • final volume: V2=0.2 L
  2. Formula: P2=P1V1V2
  3. Substitute: P1=100,000 Pa,V1=0.5 L,V2=0.2 L
  4. Answer: P2=250,000 Pa

Liters can stay as they are, because only the ratio of the volumes matters.

Example 2 Quickly squeezing the same pump (adiabatic)

Now the same 0.5 L of air at 100,000 Pa is pushed in sharply to 0.2 L, too fast for heat to escape. Taking γ = 1.4 for air, what is the new pressure?

  1. Given:
    • initial pressure: P1=100,000 Pa
    • initial volume: V1=0.5 L
    • final volume: V2=0.2 L
    • heat capacity ratio C_p/C_V (5/3 monatomic, 7/5 diatomic): γ=1.4
  2. Formula: P2=P1(V1V2)γ
  3. Substitute: P1=100,000 Pa,V1=0.5 L,V2=0.2 L,γ=1.4
  4. Answer: P2=360,700 Pa

The fast squeeze ends at a higher pressure than the slow one, because the trapped air also gets hotter.

Why Is an Adiabatic Curve Steeper on a PV Diagram?

On a PV diagram, an isothermal process traces a curve called an isotherm, where pressure times volume is constant. An adiabatic process traces a steeper curve through the same starting point.

The reason is temperature. When a gas is compressed adiabatically, it heats up, and a hotter gas pushes harder than a cooler one at the same volume. So the pressure climbs faster than it would along the isotherm. When the gas expands adiabatically, it cools, so its pressure falls faster.

The area under each curve is the work done. For the same expansion, the isothermal path gives more work, because heat keeps topping up the gas as it goes. This difference is what heat engines exploit in cycles such as the Carnot cycle, which alternates between the two kinds of process.

PV diagram of air compressed from 1 L to 0.5 L: the adiabatic curve rises more steeply and ends at a higher pressure than the isothermal curve
Squeezed fast, the air also heats up, so the adiabatic curve climbs more steeply and ends at a higher pressure than the slow, isothermal one.

Does Temperature Change in an Adiabatic Process?

Yes, and that is its most noticeable feature. For an ideal gas the temperature follows T1V1γ−1=T2V2γ−1, so a smaller volume means a higher temperature.

You may have felt this when pumping up a bicycle tire: the end of the pump gets warm because the air inside is squeezed faster than it can lose heat. The reverse happens when a can of compressed air is sprayed for a while; the gas expands quickly and the can feels cold.

In an isothermal process the temperature stays fixed by definition. Achieving that in practice needs a good thermal contact with a large reservoir, such as a water bath, and a slow enough change for heat to keep up.

Example 3 How hot does the air in the pump get?

Air at T_1 = 293 K is compressed adiabatically so that its volume falls by a ratio r = V_1/V_2 = 2.5. With γ = 1.4, what is the final temperature?

  1. Given:
    • starting temperature: T1=293 K
    • compression ratio V₁/V₂: V1/V2=2.5
    • heat capacity ratio of air: γ=1.4
  2. Formula: T2=T1(V1V2)γ−1
  3. Substitute: T1=293 K,V1/V2=2.5,γ=1.4
  4. Answer: T2=422.7 K

That is roughly 150 °C (computed). In the isothermal version the air would have stayed at 293 K, about 20 °C.

What Are Real Examples of Each Process?

Processes that are close to isothermal:

  • a gas in a thin metal cylinder expanding very slowly in a water bath
  • the steps of a refrigerator cycle where the working fluid changes phase at a steady temperature
  • slowly letting air out of a balloon in a warm room

Processes that are close to adiabatic:

  • the compression stroke of a diesel engine, fast enough to ignite fuel without a spark
  • the squeezes and stretches of air in a sound wave
  • rising air in the atmosphere, which cools as it expands and can form clouds
  • gas released from a spray can or a fire extinguisher

No real process is perfectly either one. Engineers choose the model that matches whether heat has time to flow.

Isothermal vs Adiabatic Explained Simply

Imagine a gas as a crowd of tiny moving balls in a box with a movable lid. In an isothermal change, the box sits in a warm bath, so whenever the balls lose energy pushing the lid, the bath gives it back and they keep the same average speed.

In an adiabatic change, the box is wrapped in a perfect blanket. When the balls push the lid outward, they lose energy and slow down, so the gas cools. When the lid is pushed in, the balls bounce off it faster, so the gas warms up. For more on how forms of energy compare, see heat vs temperature.

Common Misconceptions

Myth: Isothermal means no heat is transferred.

Physics: That describes an adiabatic process. In an isothermal process heat must flow to keep the temperature constant while work is done.

Myth: If no heat is added, the temperature of a gas cannot change.

Physics: Work can change the temperature too. In an adiabatic compression, the work done on the gas raises its temperature even though Q = 0.

Myth: Adiabatic and isentropic always mean the same thing.

Physics: Only a slow, reversible adiabatic process keeps entropy constant. A fast, irregular adiabatic change, like a gas rushing into a vacuum, increases entropy.

Myth: Isothermal processes involve no energy change at all.

Physics: The internal energy of an ideal gas stays the same, but energy still moves: heat flows in or out and work is done.

Key Facts

  • An isothermal process keeps temperature constant; an adiabatic process allows no heat exchange.
  • For an ideal gas in an isothermal process, ΔU = 0 and the heat added equals the work done.
  • In an adiabatic process, Q = 0, so the work done changes the internal energy directly.
  • Isothermal changes follow P V = constant, while adiabatic changes follow P V^γ = constant.
  • Adiabatic compression heats a gas and adiabatic expansion cools it.
  • An adiabatic curve is steeper than an isotherm on a PV diagram.
  • Slow changes with good heat contact are close to isothermal; fast or insulated changes are close to adiabatic.
Did you know? Clouds often form because rising air expands almost adiabatically as the pressure around it drops, cooling by several degrees for every kilometer it climbs until its water vapor condenses.

Quick Quiz: How Well Do You Know Isothermal vs Adiabatic Processes?

6 questions. Tap an answer to check it.

  1. In which process does no heat cross the system boundary?

  2. For an ideal gas in an isothermal process, what is ΔU?

  3. What happens to the temperature of a gas compressed adiabatically?

  4. Which equation describes an adiabatic process of an ideal gas?

  5. Halving the volume of a gas isothermally changes the pressure by what factor?

  6. Which change is closest to adiabatic?

Frequently Asked Questions

What is the main difference between isothermal and adiabatic processes?

In an isothermal process the temperature stays constant, and heat flows in or out as needed. In an adiabatic process no heat flows, and the temperature changes because of the work done. For an ideal gas, isothermal changes obey P V = constant, while adiabatic changes obey P V^γ = constant, which gives a steeper curve.

Which does more work, an isothermal or an adiabatic expansion?

Between the same starting state and the same final volume, the isothermal expansion does more work. Heat flowing in keeps the gas warm, so its pressure stays higher as it expands. In the adiabatic expansion, the gas cools and its pressure drops faster, so the area under its PV curve is smaller.

Why is an adiabatic process usually fast?

Heat needs time to move through walls. If a gas is compressed or expanded quickly, there is no time for significant heat to flow, so the process is effectively adiabatic even without perfect insulation. Sound waves, engine strokes and bursting gas cylinders are all fast enough to be treated as adiabatic.

Is the internal energy constant in an isothermal process?

For an ideal gas, yes. Its internal energy depends only on temperature, so if the temperature is fixed, ΔU = 0. For real substances that change phase, like water boiling at constant temperature, the internal energy can change even though the temperature stays the same, because energy goes into breaking bonds.

What is γ in the adiabatic equation?

The symbol γ, gamma, is the heat capacity ratio: the heat capacity at constant pressure divided by the heat capacity at constant volume. It is 5/3 for monatomic gases such as helium and argon and about 1.4 for diatomic gases such as air. Larger γ means a steeper adiabatic curve.

Can a process be both isothermal and adiabatic?

For an ideal gas that does work, no. If no heat flows and the gas does work, its internal energy and temperature must change. The only exception is a trivial case in which no work is done and no heat flows, so nothing changes at all. Real examples are always one or the other, or in between.

Why does a bike pump get hot?

Pushing the handle compresses the air quickly, so the process is close to adiabatic. The work you do on the air turns into internal energy, raising its temperature. Friction between the plunger and the barrel adds a little extra warmth, but most of the heating comes from the fast compression.

Where are isothermal and adiabatic processes used together?

Heat engines and refrigerators combine them. The ideal Carnot cycle uses two isothermal steps, where heat is exchanged with hot and cold reservoirs, and two adiabatic steps, where the temperature changes between those reservoirs. Real engines and heat pumps use cycles that approximate these steps.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.