The ideal heat engine

Carnot Cycle and Carnot Efficiency

The Carnot cycle is an ideal, fully reversible heat-engine cycle made of two isothermal steps and two adiabatic steps, and its efficiency, e = 1 − Tc/Th, is the highest any engine can reach between two given temperatures. No real engine matches it, but it sets the ceiling that every power plant and car engine is measured against.

Power station cooling towers releasing vapor at dusk, where waste heat to the cold reservoir limits efficiency as the Carnot cycle predicts
Cooling towers carry away the heat every engine must reject; the Carnot cycle sets how small that share can be.

At a Glance

The Carnot cycle is a theoretical heat engine cycle of isothermal expansion, adiabatic expansion, isothermal compression and adiabatic compression. Its efficiency is e = 1 - Tc/Th, with both temperatures in kelvin, and no engine working between the same two temperatures can be more efficient.

What it is
An ideal reversible heat-engine cycle
Four steps
Isothermal expansion, adiabatic expansion, isothermal compression, adiabatic compression
Efficiency formula
eC = 1 − Tc / Th (kelvin)
Units
Dimensionless, often given as a percentage
Depends on
Only the hot and cold reservoir temperatures
Proposed by
Sadi Carnot, 1824
On this page
  1. What Is the Carnot Cycle?
  2. The Carnot Cycle Explained Simply
  3. What Are the 4 Steps of the Carnot Cycle?
  4. What Is the Carnot Efficiency Formula?
  5. Why Can No Engine Beat the Carnot Efficiency?
  6. Why Don't Real Engines Reach Carnot Efficiency?
  7. How Efficient Are Real Engines Compared With the Carnot Limit?
  8. What Is a Reverse Carnot Cycle?
  9. Who Discovered the Carnot Cycle?
  10. Practice Carnot Cycle Problems
  11. Common Misconceptions
  12. Key Facts
  13. Quiz
  14. FAQ

What Is the Carnot Cycle?

The Carnot cycle is a thought experiment about the best possible heat engine. A gas in a cylinder takes in heat from a hot reservoir, turns part of it into work, and dumps the rest into a cold reservoir, then returns exactly to where it started. Every step happens so slowly and smoothly that it could be run backward without leaving any trace.

That perfect reversibility is what makes the cycle special. It wastes nothing to friction, to sudden pressure jumps or to heat flowing across a temperature gap. Because of this, it gets the most work out of each joule of heat that the laws of physics allow.

No one builds a Carnot engine to power a factory. It would run infinitely slowly and produce almost no power. Its value is as a yardstick: it tells engineers the upper limit for any engine working between two temperatures, so they know how much room is left for improvement.

The Carnot Cycle Explained Simply

Think of heat as water held behind a dam, with temperature playing the role of height. Water falling from a high lake to a low one can turn a wheel, but only if there is a drop. The bigger the drop, the more of the water's energy you can catch.

A heat engine works the same way. Heat "falls" from a hot place to a cold place, and the engine catches some of it as work. The Carnot cycle is the most careful possible catcher: it collects every bit that the temperature drop allows, and no more is ever possible.

The catch is that some heat must always reach the cold side. An engine cannot turn all of its heat into work, just as a waterwheel cannot run if the water has nowhere lower to go.

What Are the 4 Steps of the Carnot Cycle?

Picture an ideal gas in a cylinder with a frictionless piston. The cylinder can be placed against a hot reservoir at temperature Th, against a cold reservoir at Tc, or on a perfect insulator. The cycle has four stages:

  1. Isothermal expansion at Th. The gas touches the hot reservoir and expands slowly. Its temperature stays at Th, so the heat it absorbs, Qh, all leaves as work on the piston.
  2. Adiabatic expansion. The cylinder moves onto the insulator and the gas keeps expanding. No heat enters, so the gas pays for this work from its own internal energy and cools from Th down to Tc.
  3. Isothermal compression at Tc. The gas touches the cold reservoir and is squeezed slowly. Work is done on it, and it hands an amount of heat Qc to the cold reservoir while staying at Tc.
  4. Adiabatic compression. Back on the insulator, the gas is compressed further. The work done on it warms it from Tc to Th, returning it to its starting state.

On a PV diagram these four steps trace a closed loop bounded by two isotherms and two adiabats. The area inside the loop is the net work per cycle, W = Qh − Qc. For more on the two process types, see isothermal process, adiabatic process and the side-by-side guide isothermal vs adiabatic.

Example 3 Maximum work from one cycle

A Carnot engine works between 800 K and 300 K. In one cycle it takes in 2,000 J of heat from the hot reservoir. What is the most work it can deliver in that cycle?

  1. Given:
    • heat absorbed from the hot reservoir: Qh=2,000 J
    • cold-reservoir temperature: Tc=300 K
    • hot-reservoir temperature: Th=800 K
  2. Formula: Wmax=Qh(1−TcTh)
  3. Substitute: Qh=2,000 J,Tc=300 K,Th=800 K
  4. Answer: Wmax=1,250 J (1.25 kJ)

The remaining heat, the difference between 2,000 J and this answer, must go to the cold reservoir. Even a perfect engine cannot avoid it.

PV diagram of a Carnot cycle: two isotherms at 600 K and 300 K joined by two adiabats, the enclosed area shaded as net work
For 1 mol of helium doubling its volume on the hot isotherm, Q_h is about 3,458 J and the net work is about 1,729 J, exactly half, as e = 1 − 300/600 predicts (computed).

What Is the Carnot Efficiency Formula?

The efficiency of any engine is the work out divided by the heat in, e=W/Qh. For the Carnot cycle, the heats exchanged in the two isothermal steps turn out to be proportional to the reservoir temperatures, Qc/Qh=Tc/Th. Putting the two together gives the Carnot efficiency, eC=1−Tc/Th.

Both temperatures must be in kelvin. Using Celsius gives nonsense; a cold side at 0 °C would make the efficiency look like 100 percent. Convert first by adding 273.15, or use the temperature converter.

The formula has two striking features. It does not mention the gas, the size of the engine or how it is built, only the two temperatures. And it can reach 100 percent only if Tc is zero kelvin, which the absolute zero page explains is unreachable.

The Carnot efficiency needs just two numbers, the absolute temperatures of the hot and cold reservoirs. Here is the formula with its symbols and rearranged forms.

eC=1−TcTh
What each symbol means
SymbolQuantitySI unit
eCmaximum (Carnot) efficiencydimensionless (1)
Tcabsolute temperature of the cold reservoirkelvin (K)
Thabsolute temperature of the hot reservoirkelvin (K)

Rearranged to find another variable:

Tc=Th(1−eC)Th=Tc1−eC

Valid for: reversible engine; temperatures MUST be in kelvin; upper limit for any real engine.

Example 1 The limit for a geothermal power plant

A geothermal plant draws hot water from underground at 180 °C (453.15 K) and rejects waste heat to air at 25 °C (298.15 K). What is the Carnot efficiency for these temperatures, as a decimal?

  1. Given:
    • absolute temperature of the cold reservoir: Tc=298.15 K
    • absolute temperature of the hot reservoir: Th=453.15 K
  2. Formula: eC=1−TcTh
  3. Substitute: Tc=298.15 K,Th=453.15 K
  4. Answer: eC=0.3421

Multiply by 100 for a percentage. Real geothermal plants reach well under this ceiling because of friction, heat leaks and pumping losses.

Why Can No Engine Beat the Carnot Efficiency?

The answer comes from the second law of thermodynamics. Suppose some engine were more efficient than a Carnot engine between the same two reservoirs. You could use its output to drive the Carnot engine backward as a refrigerator. The combination would move heat from the cold reservoir to the hot one with no outside work, which the second law forbids.

This result is called Carnot's theorem. It has two parts. No engine between two reservoirs can beat a reversible one, and every reversible engine between the same two reservoirs has the same efficiency, whatever its working substance.

In entropy terms, the Carnot cycle creates no new entropy. The entropy the gas takes from the hot reservoir, Qh/Th, equals the entropy it gives to the cold one, Qc/Tc. Any real loss, such as friction, adds entropy and lowers the work you get.

Example 2 How hot must the source be?

An engineer wants an engine whose ideal (Carnot) efficiency is 0.60, with a cold reservoir at 300 K. What is the lowest hot-reservoir temperature that makes this possible?

  1. Given:
    • maximum (Carnot) efficiency: eC=0.6
    • absolute temperature of the cold reservoir: Tc=300 K
  2. Formula: Th=Tc1−eC
  3. Substitute: eC=0.6,Tc=300 K
  4. Answer: Th=750 K

That is about 477 °C. Raising the hot temperature is the main way engineers push efficiency up, which is why modern turbines run so hot.

Why Don't Real Engines Reach Carnot Efficiency?

Real engines run fast, and speed brings losses. Heat only flows quickly across a real temperature difference, and heat flowing from hot to cold across a gap is an irreversible process that wastes some of its ability to do work. The conduction diagram below shows this kind of flow.

Moving parts rub, gases swirl and mix, and some heat leaks out through the engine walls without ever passing through the cycle. Combustion engines also follow different cycles, such as the Otto and Diesel cycles, which have lower ideal efficiencies than a Carnot engine between the same extreme temperatures.

As a rough guide, good large power plants reach about 60 to 70 percent of their Carnot limit. The table compares the ideal ceiling with typical real values for several kinds of plant.

Copper bar conducting heat directly from a 600 K reservoir to a 300 K reservoir, an irreversible flow that produces no work
Heat crossing a temperature gap directly is irreversible: the 60 W flowing here could have run an engine but does no work at all.

How Efficient Are Real Engines Compared With the Carnot Limit?

The Carnot formula explains several big engineering choices. Ocean thermal plants, which use the small difference between warm surface water and cold deep water, have a tiny ceiling and need enormous flows to produce useful power. Steam plants push their boiler temperatures as high as their steel can safely handle, because every extra degree raises the ceiling.

Combined-cycle gas plants do best of all. They burn gas in a turbine at very high temperature, then use the hot exhaust to raise steam for a second turbine. The pair works across a much larger temperature span than either could alone. For how energy flows through a typical engine, see energy efficiency and our guide to the internal combustion engine.

Carnot limit compared with typical real efficiency for several kinds of power plant
Type of plantHot side (°C)Cold side (°C)Carnot limit (%)Typical real efficiency
Ocean thermal energy2556.7about 3%
Geothermal1802534.2about 10–20%
Nuclear (pressurized water)2853045.7about 33%
Coal-fired steam5503063.2about 33–40%
Combined-cycle gas turbine1,4003081.9about 55–62%
Source: Carnot limit computed with e = 1 − Tc/Th (temperatures converted to kelvin); reservoir temperatures and real efficiencies are typical values · Retrieved October 2026

What Is a Reverse Carnot Cycle?

Because every step is reversible, the Carnot cycle can be run backward. Then work goes in, heat is pulled from the cold reservoir, and a larger amount of heat is delivered to the hot reservoir. That is an ideal refrigerator or heat pump.

For the reversed cycle, the best possible coefficient of performance of a refrigerator is K=Tc/(Th−Tc). The closer the two temperatures are, the less work it takes to move each joule of heat, which is why a heat pump works best when the outdoor air is not too cold.

Who Discovered the Carnot Cycle?

The French engineer Sadi Carnot described the cycle in 1824 in a short book on the motive power of fire. He wanted to know how much work steam engines could possibly produce and whether a better working fluid would help. His key insight was that the work depends on the temperature difference, not the substance.

Carnot thought of heat as a fluid that was conserved as it flowed, an idea later abandoned. In the 1830s Émile Clapeyron restated the cycle with graphs of pressure against volume. Around 1850, Rudolf Clausius and William Thomson, later Lord Kelvin, rebuilt Carnot's reasoning on the conservation of energy, and that work grew into the second law and the absolute temperature scale. Carnot died young, in 1832, before his ideas were widely known.

Historic stationary steam engine with a large flywheel in a brick engine house, the kind of machine Carnot studied
Carnot's 1824 analysis began as a question about steam engines like this one: how much work can heat possibly give?

Practice Carnot Cycle Problems

Most Carnot problems ask for one of three things: the maximum efficiency, a missing temperature, or the most work available from a given heat input. Work through the three examples above, then check the general efficiency rules on the heat engine page. Our thermodynamics formula sheet lists every equation in one place, and the quiz below checks your understanding.

Common Misconceptions

Myth: A good enough engine could turn all of its heat into work.

Physics: The Carnot limit is always below 100 percent unless the cold side is at absolute zero. Some heat must always go to the cold reservoir.

Myth: You can use Celsius temperatures in e = 1 − Tc/Th.

Physics: The formula only works with absolute temperatures in kelvin. Celsius values give wrong and sometimes impossible answers.

Myth: A better working gas would let an engine beat the Carnot efficiency.

Physics: Carnot's theorem says every reversible engine between the same two temperatures has the same efficiency, whatever the substance inside.

Myth: The Carnot engine is the most powerful engine.

Physics: It is the most efficient, not the most powerful. Its steps must be infinitely slow, so its power output would be close to zero.

Key Facts

  • The Carnot cycle is an ideal reversible heat engine cycle with two isothermal and two adiabatic steps.
  • Its efficiency is e = 1 − Tc/Th, with both temperatures measured in kelvin.
  • No engine operating between the same two temperatures can be more efficient than a Carnot engine.
  • The Carnot efficiency depends only on the reservoir temperatures, not on the working gas or engine design.
  • Even an ideal engine must reject some heat to the cold reservoir, so its efficiency is always below 100 percent.
  • Run in reverse, the Carnot cycle becomes the ideal refrigerator or heat pump.
  • Sadi Carnot published the idea in 1824, decades before the first and second laws were stated in their modern form.
Did you know? A Carnot engine running between boiling water and freezing water could turn at most about 27 percent of its heat into work, even with zero friction and perfect parts.

Quick Quiz: How Well Do You Know Carnot Cycle and Carnot Efficiency?

6 questions. Tap an answer to check it.

  1. Which pair of processes makes up the Carnot cycle?

  2. A Carnot engine works between 500 K and 300 K. What is its efficiency?

  3. What unit must temperatures be in for the Carnot formula?

  4. What happens to the Carnot efficiency if the hot reservoir gets hotter?

  5. During which step does the gas absorb heat from the hot reservoir?

  6. Which law of physics guarantees that no engine beats the Carnot efficiency?

Frequently Asked Questions

What is the Carnot cycle in simple terms?

It is the ideal way to run a heat engine. A gas takes in heat at a high temperature, does work while expanding, gives off heat at a low temperature, and is compressed back to its starting point. Every step is perfectly smooth and reversible, so nothing is wasted. It shows the largest share of heat that any engine could turn into work.

What are the four processes of the Carnot cycle?

The four processes are isothermal expansion at the hot temperature, adiabatic expansion that cools the gas to the cold temperature, isothermal compression at the cold temperature, and adiabatic compression that warms the gas back to the hot temperature. Heat is exchanged only during the two isothermal steps; the adiabatic steps change the temperature without any heat flow.

How do you calculate Carnot efficiency?

Convert both reservoir temperatures to kelvin, divide the cold temperature by the hot temperature, and subtract the result from one: e = 1 − Tc/Th. Multiply by 100 for a percentage. For example, a hot side at 600 K and a cold side at 300 K give 1 − 0.5 = 0.5, or 50 percent, as the highest possible efficiency.

Why is the Carnot cycle not used in real engines?

To stay reversible, heat must flow across almost no temperature difference, which makes every step extremely slow. A real Carnot engine would deliver almost no power. The isothermal steps are also hard to achieve in practice, and the PV loop is very thin for gases, so friction would eat most of the work. Engineers use faster cycles and accept lower efficiency.

Can a heat engine have 100 percent efficiency?

No. Even the ideal Carnot engine reaches 100 percent only if its cold reservoir is at absolute zero, and absolute zero cannot be reached. The second law of thermodynamics says some heat must always flow to a colder place. Real engines also lose energy to friction and heat leaks, so they stay well below their Carnot limit.

How can you increase Carnot efficiency?

Make the temperature ratio Tc/Th smaller. In practice that means raising the hot temperature, since the cold side is usually set by the surrounding air or water. Lowering the cold temperature helps too, which is why power plants run slightly better in winter. Changing the gas or the engine size has no effect on the Carnot limit itself.

What is the difference between Carnot efficiency and actual efficiency?

Carnot efficiency is the theoretical ceiling set by two temperatures. Actual efficiency is what a real engine achieves, the work it delivers divided by the heat it uses. The actual value is always lower because of friction, heat leaks, fast irreversible steps and a cycle design that differs from Carnot's. Comparing the two shows how much improvement is still possible.

Does the Carnot cycle increase entropy?

No. Over one full Carnot cycle, the total entropy of the gas and both reservoirs stays the same. The gas takes entropy Qh/Th from the hot reservoir and gives the same amount, Qc/Tc, to the cold one. That zero entropy production is exactly what reversible means, and it is why no engine can do better.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.