Why a liquid surface acts like a stretched skin

Surface Tension

Surface tension is the tendency of a liquid surface to pull itself tight and resist being stretched, measured as a force per unit length in newtons per meter. It exists because molecules at the surface are pulled inward by their neighbors, with nothing equal pulling them outward. Clean water at room temperature has a surface tension of about 0.072 N/m, high enough to float a paper clip.

Water strider standing on a pond, its legs pressing dimples into the water surface held up by surface tension
A water strider dents the surface without breaking it, held up by surface tension.

At a Glance

Surface tension is the force per unit length that a liquid surface exerts along itself, γ = F / L, measured in N/m. It is caused by the unbalanced inward pull on surface molecules, and for water at about 20 °C it is roughly 0.073 N/m. Soap and heat both lower it.

Symbol
γ (gamma), sometimes σ or T
SI unit
newton per meter (N/m), equal to J/m²
Formula
γ = F / L
Water at 20 °C
about 0.0728 N/m (72.8 mN/m)
Caused by
Cohesive forces between liquid molecules
Lowered by
Soaps and detergents, rising temperature
On this page
  1. What Is Surface Tension?
  2. What Causes Surface Tension?
  3. How Does Surface Tension Hold Up a Paper Clip?
  4. How Do You Calculate Surface Tension?
  5. Why Is the Surface Tension of Water So High?
  6. What Lowers Surface Tension?
  7. Where Do You See Surface Tension in Everyday Life?
  8. How Is Surface Tension Related to Capillary Action?
  9. Common Misconceptions
  10. Key Facts
  11. Quiz
  12. FAQ

What Is Surface Tension?

Surface tension is the reason a liquid surface behaves as if a thin elastic sheet were stretched across it. Gently set a dry steel paper clip on still water and it floats, even though steel is about eight times denser than water. The clip rests in a small dent in the surface, and the surface pulls back like a trampoline.

Physicists describe the effect with a single number, the surface tension γ. Picture a line drawn across the surface of a liquid. The liquid on each side pulls on that line, and γ is the size of that pull for every meter of line. The unit is the newton per meter, which is the same as a joule per square meter.

That second unit gives another useful view. Surface tension is also the energy it costs to create one extra square meter of surface. Liquids lower their energy by keeping their surface area as small as possible, which is why free drops pull themselves into spheres.

What Causes Surface Tension?

The cause is the attraction between molecules of the same liquid, called cohesion. A molecule deep inside a glass of water is surrounded on all sides, so the pulls from its neighbors cancel. A molecule at the surface has liquid beside and below it but only air above, so the pulls no longer cancel.

The leftover pull on each surface molecule points inward, toward the bulk of the liquid. The surface molecules are squeezed together and the surface behaves as if it were under tension. Bringing a molecule from the inside to the surface takes work, so a larger surface always means more stored energy.

How strong the effect is depends on the intermolecular forces in the liquid. Water molecules form hydrogen bonds with each other, which are strong for such small molecules, so water has one of the highest surface tensions of any common liquid. Oils and alcohols attract each other more weakly and have much lower values.

How Does Surface Tension Hold Up a Paper Clip?

Here is what happens, step by step, when a small steel object rests on water:

  1. The clip is lowered flat and dry onto still water, so it does not break through.
  2. Its weight presses the surface down, forming a shallow dimple along the wire.
  3. The bent surface on each side of the wire pulls along its own slope, partly upward.
  4. The upward parts of those pulls add up and balance the weight of the clip.
  5. If the clip is pushed deeper than the surface can bend, or soap is added, the balance fails and the clip sinks.

The diagram shows the forces on a clip of about 0.5 g. Each side of the dimple pulls at 60° above the horizontal, and the two upward parts together match the 4.9 mN weight. The forces were computed from the weight and the angle, and the sideways parts cancel.

Free-body diagram of a paper clip on water, two slanted 2.83 mN surface tension pulls balancing a 4.9 mN weight
The upward parts of the two surface pulls (2 × 2.83 mN × sin 60°) balance the clip's 4.9 mN weight (computed).

How Do You Calculate Surface Tension?

The defining equation is γ=F/L: the force along the surface divided by the length of the edge it acts on. With force in newtons and length in meters, the result is in newtons per meter. Values for everyday liquids are small, so you will often see them in millinewtons per meter, where water is about 72 mN/m.

Watch out for films with two sides. A soap film or a film lifted under a wire has a front surface and a back surface, and both pull. In that case the force is F=2γL, and forgetting the 2 is the most common mistake in these problems.

In the lab, surface tension is usually measured by pulling a thin ring or plate out of the liquid and recording the largest extra force before the film lets go. The two worked examples below follow that idea.

Surface tension is defined as the force a surface pulls with, divided by the length of the edge it pulls along.

γ=FL
What each symbol means
SymbolQuantitySI unit
γsurface tensionnewton per meter (N/m)
Fforce along the surfacenewton (N)
Llength of the line over which the force actsmeter (m)

Rearranged to find another variable:

F=γLL=Fγ

Valid for: for a film with two surfaces (e.g. soap film on a wire frame) L counts both: F = 2γl.

Example 1 Holding a soap film on a wire frame

A soap film is stretched across a U-shaped wire frame, and a light sliding wire 0.06 m long closes the fourth side. The soap solution has a surface tension of 0.025 N/m. The film has a front and a back surface. What force does the film exert on the sliding wire?

  1. Given:
    • surface tension: γ=0.025 N/m
    • length of the line over which the force acts: L=0.06 m
  2. Formula: F=2γL
  3. Substitute: γ=0.025 N/m,L=0.06 m
  4. Answer: F=0.003 N

The factor of 2 is there because both faces of the film pull on the wire.

Example 2 Measuring an unknown liquid

A student dips a straight wire 0.05 m long into an unknown liquid and lifts it slowly. Just before the thin film under the wire breaks, a sensitive force meter shows an extra pull of 0.0045 N. The film touches the wire on both sides. What is the liquid's surface tension?

  1. Given:
    • force along the surface: F=0.0045 N
    • length of the line over which the force acts: L=0.05 m
  2. Formula: γ=F2L
  3. Substitute: F=0.0045 N,L=0.05 m
  4. Answer: γ=0.045 N/m

That value sits between alcohols and pure water in the table below, so the liquid could be a water mixture with some soap or alcohol in it.

Why Is the Surface Tension of Water So High?

Each water molecule can form hydrogen bonds with up to four neighbors. Those links are much stronger than the weak attractions between the molecules of oils or alcohols. A surface water molecule loses some of those bonds, and that missing bonding energy shows up as a high surface tension.

Among common liquids only mercury beats water, by a wide margin, because the atoms in a liquid metal are held together by metallic bonding. The table lists typical values near room temperature. Notice how close the alcohols and oils sit to each other, and how far below water they are.

Surface tension of common liquids near 20 °C
LiquidSurface tension (mN/m)Surface tension (N/m)
Mercuryabout 4860.486
Water72.80.0728
Glycerolabout 630.063
Olive oilabout 320.032
Soapy waterabout 25 to 300.025 to 0.030
Acetoneabout 240.024
Ethanolabout 220.022
Source: Typical rounded values against air near room temperature; soapy water depends on the soap and its concentration · Retrieved October 2026

What Lowers Surface Tension?

Soaps and detergents are the big one. Their molecules have one end that likes water and one end that avoids it, so they crowd onto the surface with their water-avoiding tails sticking out. That breaks up the tight network of surface water molecules and can cut the surface tension to roughly a third of its usual value. Lower surface tension lets water spread into fabric and lift away grease, which is why washing works.

Heat also weakens surface tension. Faster molecules hold each other less tightly, so the value falls steadily as the temperature rises, as the second table shows. Hot water cleans better partly for this reason.

Dissolved salts tend to raise surface tension slightly, while alcohols lower it. A drop of dish soap placed in a bowl of water sprinkled with pepper shows the effect at once: the pepper rushes to the rim as the surface near the soap loses its pull.

Surface tension of pure water at different temperatures
Temperature (°C)Temperature (°F)Surface tension (mN/m)
032about 75.6
2068about 72.8
40104about 69.6
60140about 66.2
80176about 62.6
100212about 58.9
Source: Typical values for pure water against air; °F computed with °F = 1.8 × °C + 32 · Retrieved October 2026

Where Do You See Surface Tension in Everyday Life?

  • Water striders stand on ponds. Their legs are covered in water-repellent hairs, so they dimple the surface without breaking through.
  • Round drops form from a dripping tap and in rain, because a sphere has the least surface for its volume.
  • Soap bubbles are thin films held together by surface tension, and the soap lowers it enough for the film to last.
  • Wet hair and paintbrushes clump together when pulled from water, because the water film pulls the strands into the smallest shape.
  • Your lungs make a natural substance that lowers surface tension in the tiny air sacs, so they do not collapse each time you breathe out.
  • Inkjet printers rely on surface tension to pinch the jet of ink into tiny, evenly sized drops.

A slightly overfilled glass is a neat home demonstration. Add water slowly and the surface bulges above the rim before it finally spills, held in place by its own tension.

Example 3 How much leg does a water strider need?

A water strider of about 20 mg weighs roughly 0.0002 N. Assume each part of its legs in contact with the water is pulled upward by the surface on both sides, with water's surface tension taken as 0.072 N/m. What total length of leg must touch the water to support the insect?

  1. Given:
    • force along the surface: F=2×10−4 N
    • surface tension: γ=0.072 N/m
  2. Formula: L=F2γ
  3. Substitute: F=2×10−4 N,γ=0.072 N/m
  4. Answer: L=0.001389 m

Real striders spread their weight over several centimeters of water-repellent leg, giving them a wide safety margin.

Soap bubbles with swirling rainbow films floating in a garden, thin liquid films held together by surface tension
A soap bubble is a liquid film only a few hundred nanometers thick, held together by surface tension.

Common Misconceptions

Myth: A floating paper clip is held up by buoyancy, just like a boat.

Physics: The clip displaces far too little water for buoyancy to hold it. The upward pull of the bent surface does most of the work.

Myth: Surface tension and viscosity are the same thing.

Physics: Viscosity is resistance to flow throughout the liquid. Surface tension acts only at the surface and can be high in a runny liquid like water.

Myth: There is a real skin of different material on top of water.

Physics: The surface layer is ordinary water. It only behaves like a skin because its molecules are pulled inward by the liquid below.

Key Facts

  • Surface tension is the force per unit length along a liquid surface, γ = F / L, measured in N/m.
  • It is caused by the unbalanced inward pull on molecules at the surface of a liquid.
  • Pure water has a surface tension of about 0.0728 N/m at 20 °C, among the highest of common liquids.
  • Soaps and detergents gather at the surface and can lower water's surface tension to roughly a third.
  • Surface tension falls as temperature rises, because warmer molecules attract each other less firmly.
  • Small drops are nearly spherical because a sphere holds a given volume with the least surface area.
  • A film with two faces, like a soap film, pulls with a force of 2γL on its edge.
Did you know? In orbit, where nothing flattens a drop under its own weight, astronauts have filmed large blobs of floating water pulling themselves into wobbling spheres, shaped by surface tension alone.

Quick Quiz: How Well Do You Know Surface Tension?

6 questions. Tap an answer to check it.

  1. What is the SI unit of surface tension?

  2. Why do surface molecules feel a net inward pull?

  3. What happens to water's surface tension when you add dish soap?

  4. A soap film pulls on a 0.1 m wire. Why is the force 2γL rather than γL?

  5. How does heating water change its surface tension?

  6. Which common liquid has a higher surface tension than water?

Frequently Asked Questions

What is surface tension in simple words?

Surface tension is the way the top layer of a liquid pulls itself tight, so it acts a little like a stretched rubber sheet. It happens because the molecules at the surface are pulled inward by the liquid below them. Thanks to it, small insects can walk on water, drops stay round, and a carefully placed paper clip can float.

What is the unit of surface tension?

The SI unit is the newton per meter, N/m, because surface tension is a force divided by a length. It can also be written as joules per square meter, since it equals the energy needed to make one extra square meter of surface. Values for liquids are small, so tables often use millinewtons per meter, where water is about 72 mN/m.

Why does water have high surface tension?

Water molecules attract each other strongly through hydrogen bonds, and each one can link to several neighbors. A molecule at the surface loses some of those links, so pulling molecules to the surface costs a lot of energy. That shows up as a high surface tension of about 0.073 N/m at room temperature, higher than almost every other common liquid except mercury.

How does soap reduce surface tension?

Soap molecules have a head that is attracted to water and a tail that avoids it. They pile up at the surface with the tails pointing out, pushing apart the water molecules that normally pull on each other. The surface tension drops sharply, often to about a third of its usual value, which helps water soak into cloth and carry dirt and grease away.

Does temperature affect surface tension?

Yes. As a liquid warms, its molecules move faster and hold on to each other less firmly, so surface tension falls. Pure water drops from about 75.6 mN/m near freezing to about 58.9 mN/m at its boiling point. This is one reason warm water wets surfaces and cleans better than cold water.

How do water striders walk on water?

A water strider is very light and spreads its weight across long legs covered with tiny water-repellent hairs. The legs press small dents into the surface without breaking it, and the bent surface pulls back upward along each leg. Because the insect weighs so little, the upward pull from surface tension is easily enough to hold it up.

Why are water drops round?

Surface tension makes a liquid shrink its surface to the smallest area it can. For a given volume, a sphere has the smallest possible surface, so a small drop pulls itself into a ball. Larger drops get flattened by their own weight, which is why a puddle is flat while a tiny dew drop is almost perfectly round.

What is an example of surface tension at home?

Fill a glass to the brim, then add water drop by drop. The surface bulges above the rim before it spills. You can also float a dry paper clip on water using a fork to lower it, then add a drop of dish soap and watch it sink. Both show the surface acting like a stretched skin.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.