How liquids climb narrow spaces

Capillary Action

Capillary action is the rise or fall of a liquid in a narrow tube or tiny gap, caused by the combined pull of adhesion to the walls and surface tension within the liquid. Water climbs up a thin glass tube, a paper towel and a candle wick this way. The narrower the space, the higher the liquid goes, and some liquids such as mercury are pushed down instead.

Blue water climbing up a paper towel strip dipped in a glass, a clear everyday example of capillary action
Water climbs the tiny gaps between paper fibers, well above the level in the glass.

At a Glance

Capillary action is the movement of a liquid up or down a narrow space caused by adhesion to the walls and surface tension. The height is h = 2 γ cos θ / (ρ g r), so halving the tube radius doubles the rise. Water rises about 30 mm in a 1 mm glass tube, while mercury is pushed down.

Also called
Capillarity, capillary motion, wicking
Formula
h = 2γ cos θ / (ρgr)
Driven by
Adhesion to the walls plus surface tension
Opposed by
The weight of the raised liquid
Water in a 1 mm glass tube
rises about 30 mm (computed)
Rise or fall?
Rises if contact angle < 90°, falls if > 90°
On this page
  1. What Is Capillary Action?
  2. What Causes Capillary Action?
  3. How Does Water Climb a Narrow Tube, Step by Step?
  4. How High Does a Liquid Rise in a Capillary Tube?
  5. Why Does Mercury Sink in a Glass Tube?
  6. Where Do You See Capillary Action?
  7. Does Capillary Action Lift Water to the Top of Trees?
  8. How Is Capillary Action Related to Other Surface Effects?
  9. Common Misconceptions
  10. Key Facts
  11. Quiz
  12. FAQ

What Is Capillary Action?

Capillary action is the ability of a liquid to move through a very narrow space without any pump, and often against gravity. Dip the corner of a paper towel into a spilled drink and the stain creeps upward through the sheet. Stand a thin glass tube in water and the water inside climbs above the level in the dish.

The word comes from the Latin for hair, because the effect is strongest in tubes about as thin as a hair. In a wide glass you barely notice it, apart from a slight upward curve at the edge. In a tube a fraction of a millimeter across, water can rise many centimeters.

Capillary action can also run the other way. If a liquid avoids the walls instead of clinging to them, it is pushed down inside the tube. Both cases come from the same physics and the same formula.

What Causes Capillary Action?

Two kinds of molecular attraction compete. Adhesion is the pull between the liquid and the wall, and cohesion is the pull of the liquid's molecules on each other. Water is strongly attracted to clean glass, so it creeps up the wall and the surface curves upward into a dish shape called a concave meniscus.

That curved surface is under surface tension. All around the rim, where the liquid meets the wall, the surface pulls along its own slope, which is mostly upward. The pull drags the whole column up with it.

The column stops when its weight equals the upward pull. In a wide tube the weight of even a small rise is large compared with the short rim, so the rise stays tiny. In a narrow tube the rim is short but the column is far lighter still, so the liquid can climb much higher.

How Does Water Climb a Narrow Tube, Step by Step?

  1. The tube touches the water, and water molecules are attracted to the glass more than to each other.
  2. A thin layer of water spreads up the inner wall, curving the surface into a concave meniscus.
  3. Surface tension in the curved surface pulls upward around the whole rim of the tube.
  4. The pull lifts a column of water, which gets heavier the higher it rises.
  5. The rise stops when the column's weight equals the total upward pull, and the level then stays put.

The diagram shows that final balance for water in a tube 1 mm across. The upward pull around the rim is 2πrγ, about 229 µN, and the raised column, about 30 mm tall, weighs exactly the same. Both values were computed from the capillary formula and the density of water.

Force diagram for water raised in a 1 mm capillary tube, a 229 µN upward surface pull balancing a 229 µN weight
At equilibrium the surface pull 2πrγ equals the weight of the raised column, about 229 µN in a 1 mm tube (computed).

How High Does a Liquid Rise in a Capillary Tube?

The height follows h=2γcos⁡θ/(ρgr), sometimes called Jurin's law. Here γ is the surface tension, θ the contact angle between the liquid and the wall, ρ the density of the liquid, g the acceleration due to gravity and r the inner radius of the tube.

The radius sits on the bottom of the fraction, so the rise is inversely proportional to it. Halve the radius and the rise doubles; shrink it tenfold and the rise grows tenfold. The table shows the pattern for water in clean glass.

The formula works best for narrow, round, clean tubes. In very wide tubes the meniscus flattens and the simple model no longer fits, and dirt or grease on the glass changes the contact angle and spoils the result.

The height comes from balancing the upward pull of the surface around the rim against the weight of the raised column.

h=2γcos⁡θρgr
What each symbol means
SymbolQuantitySI unit
hheight of the liquid columnmeter (m)
γsurface tensionnewton per meter (N/m)
θcontact angleradian (rad)
ρliquid densitykilogram per cubic meter (kg/m³)
gacceleration due to gravity (9.80 m/s² (standard 9.80665 m/s²))meter per second squared (m/s²)
rtube radiusmeter (m)

Rearranged to find another variable:

r=2γcos⁡θρghγ=ρgrh2cos⁡θ

Valid for: narrow cylindrical tube; θ > 90° gives depression (h < 0).

Example 1 Water in a thin glass tube

A clean glass tube with an inner radius of 0.25 mm (0.00025 m) is dipped into water at 20 °C. Take the surface tension as 0.0728 N/m, the contact angle as 0°, the density as 998 kg/m³ and g = 9.81 m/s². How high does the water rise?

  1. Given:
    • surface tension: γ=0.0728 N/m
    • contact angle: θ=0 °
    • liquid density: ρ=998 kg/m3
    • acceleration due to gravity: g=9.81 m/s2
    • tube radius: r=2.5×10−4 m
  2. Formula: h=2γcos⁡θρgr
  3. Substitute: γ=0.0728 N/m,θ=0 °,ρ=998 kg/m3,g=9.81 m/s2,r=2.5×10−4 m
  4. Answer: h=0.05949 m

That is about 6 cm, easy to see with the naked eye in a lab capillary tube.

Capillary rise of water in clean glass tubes of different sizes
Inner diameter (mm)Inner radius (mm)Rise (mm)
0.10.05297.4
0.20.1148.7
0.50.2559.5
10.529.7
2114.9
52.55.9
1053.0
Source: Computed with h = 2γcosθ/(ρgr), γ = 0.0728 N/m, θ = 0°, ρ = 998 kg/m³, g = 9.81 m/s² (water at about 20 °C, typical values) · Retrieved October 2026

Why Does Mercury Sink in a Glass Tube?

Mercury atoms attract each other far more strongly than they attract glass. Instead of creeping up the wall, mercury pulls away from it, and its surface bulges upward in the middle into a convex meniscus. The contact angle is larger than 90°.

In the formula, the cosine of an angle above 90° is negative, so the height comes out negative. The liquid inside the tube settles below the level outside. This is called capillary depression, and it is the reason careful readings of a mercury column were taken at the top of the curved surface.

The same thing happens with water in a tube coated with wax or a nonstick polymer. Whether a liquid rises or falls is decided by the contact angle, which the table summarizes for a few common pairs.

Example 2 Mercury pushed down in glass

A glass tube with an inner radius of 0.5 mm (0.0005 m) is dipped into mercury. Mercury has a surface tension of about 0.486 N/m, a contact angle with glass of about 140° and a density of 13,534 kg/m³. With g = 9.81 m/s², what is the capillary height?

  1. Given:
    • surface tension: γ=0.486 N/m
    • contact angle: θ=140 °
    • liquid density: ρ=13,534 kg/m3
    • acceleration due to gravity: g=9.81 m/s2
    • tube radius: r=5×10−4 m
  2. Formula: h=2γcos⁡θρgr
  3. Substitute: γ=0.486 N/m,θ=140 °,ρ=13,534 kg/m3,g=9.81 m/s2,r=5×10−4 m
  4. Answer: h=−0.01122 m

The minus sign means the mercury inside the tube sits below the level outside: a capillary depression.

Contact angle and capillary behavior for common liquid and surface pairs
Liquid on surfaceTypical contact angleMeniscusIn a narrow tube
Water on clean glassabout 0°ConcaveRises
Ethanol on clean glassabout 0°ConcaveRises
Water on paraffin waxabout 105° to 110°ConvexFalls
Water on PTFE nonstick coatingabout 110°ConvexFalls
Mercury on glassabout 140°ConvexFalls
Source: Typical values for clean surfaces at room temperature; real angles vary with surface finish and contamination · Retrieved October 2026

Where Do You See Capillary Action?

  • Paper towels and sponges soak up spills because water climbs through the tiny gaps between fibers.
  • Candle and oil-lamp wicks lift liquid fuel up to the flame.
  • Soil pulls water up from below through the narrow spaces between grains, keeping roots moist between rains.
  • Fountain pens feed ink to the nib through a narrow slit.
  • Clinics collect a drop of blood from a fingertip in a thin glass tube that fills on its own.
  • Rising damp in old brick walls is groundwater wicking up through the pores of the masonry.
  • Sportswear uses fine synthetic fibers that wick sweat away from the skin to the outer surface, where it evaporates.

A simple home test: stand a strip of paper towel in a glass with a little colored water and watch the color climb. A celery stalk in dyed water shows a similar trail over a few hours, although the plant adds its own pull from evaporation at the leaves.

Example 3 Designing a wick that lifts water 10 cm

An engineer wants water (surface tension 0.0728 N/m, contact angle 0°, density 998 kg/m³) to climb 0.10 m up the channels of a wick. Modeling each channel as a round tube and using g = 9.81 m/s², what is the largest channel radius that will work?

  1. Given:
    • surface tension: γ=0.0728 N/m
    • contact angle: θ=0 °
    • liquid density: ρ=998 kg/m3
    • acceleration due to gravity: g=9.81 m/s2
    • height of the liquid column: h=0.1 m
  2. Formula: r=2γcos⁡θρgh
  3. Substitute: γ=0.0728 N/m,θ=0 °,ρ=998 kg/m3,g=9.81 m/s2,h=0.1 m
  4. Answer: r=1.487×10−4 m

Channels a little narrower than about 0.15 mm will do it, which is why wicks are made from fine fibers.

Close-up of a burning candle whose wick draws melted wax up to the flame by capillary action
A candle wick lifts melted wax to the flame through the fine gaps between its fibers.

Does Capillary Action Lift Water to the Top of Trees?

Only partly. The water-carrying vessels in a tree are typically tens of micrometers wide. Using the formula, a tube 20 µm across lifts water about 1.5 m, which we computed for clean, fully wetting walls. That is far short of the top of a tall tree.

The main driver is evaporation from the leaves. As water leaves through tiny pores, it tugs on the unbroken chains of water molecules below, which hold together thanks to cohesion. Capillary forces help keep those columns filled and attached to the vessel walls, but the pull from above does the heavy lifting.

Common Misconceptions

Myth: Capillary action means water always flows upward in tubes.

Physics: Water rises only in tubes it wets. In a waxy or nonstick tube it is pushed down, and mercury sinks in ordinary glass.

Myth: Capillary action is what lifts sap to the top of giant trees.

Physics: Capillary rise in tree vessels is only around a meter or two. Evaporation from leaves, pulling on cohesive water columns, provides most of the lift.

Myth: A thicker liquid like honey cannot rise in a capillary tube.

Physics: Viscosity only slows the climb. The final height depends on surface tension, contact angle, density and radius.

Key Facts

  • Capillary action is the rise or fall of a liquid in a narrow space caused by adhesion and surface tension.
  • The capillary height is h = 2γ cos θ / (ρgr), so a narrower tube gives a higher rise.
  • Water rises about 30 mm in a clean glass tube 1 mm across.
  • Liquids with a contact angle below 90° rise; those above 90°, such as mercury on glass, are pushed down.
  • The rise stops when the weight of the raised column equals the upward pull of the surface around the rim.
  • Paper towels, wicks, soil and sportswear fabrics all move liquids by capillary action.
  • Capillary forces alone cannot lift water to the top of tall trees; evaporation from leaves does most of that work.
Did you know? A clean glass tube only 0.1 mm across can lift water about 30 cm, roughly the length of a school ruler, using nothing but surface tension and the pull of the glass (computed with the capillary rise formula).

Quick Quiz: How Well Do You Know Capillary Action?

6 questions. Tap an answer to check it.

  1. What two effects combine to produce capillary action?

  2. If the radius of a capillary tube is halved, the rise of water becomes

  3. Mercury in a glass tube shows a

  4. What stops the water from rising further in a capillary tube?

  5. Which everyday object works mainly by capillary action?

  6. A contact angle of 100° means the liquid in a narrow tube will

Frequently Asked Questions

What is capillary action in simple terms?

Capillary action is when a liquid moves through a very narrow space on its own, often climbing upward. It happens because the liquid is attracted to the walls of the space and its surface pulls the rest of the liquid along. You see it when a paper towel soaks up a spill or when a candle wick draws melted wax up to the flame.

What causes capillary action?

It is caused by adhesion and surface tension working together. Adhesion pulls the liquid toward the walls of a narrow tube, curving the surface. Surface tension in that curved surface then pulls the whole column upward. The liquid keeps rising until the weight of the raised column balances the pull. If the liquid avoids the walls, the same forces push it down instead.

Why does a narrower tube make water rise higher?

The upward pull acts around the rim, so it grows with the tube's radius, while the weight of the column grows with the radius squared. Making the tube narrower shrinks the weight faster than the pull. As a result the liquid must climb higher before its weight catches up. In the formula the radius is on the bottom, so halving it doubles the rise.

What is the formula for capillary rise?

The capillary rise formula is h = 2 γ cos θ / (ρ g r). Here h is the height, γ the surface tension, θ the contact angle, ρ the liquid density, g the acceleration due to gravity and r the tube radius. Use SI units throughout and the height comes out in meters. A negative answer means the liquid is pushed down.

Why does mercury go down in a capillary tube?

Mercury atoms attract each other much more strongly than they attract glass, so the liquid pulls away from the wall. Its surface curves into a dome and the contact angle is about 140°. Because the cosine of that angle is negative, the capillary formula gives a negative height. The mercury inside the tube settles below the level of the mercury outside.

How do plants use capillary action?

Capillary action helps soil hold water near the roots and helps keep the narrow vessels in stems filled with water. It cannot lift water more than a meter or two on its own, though. In tall plants, most of the lift comes from water evaporating from the leaves, which pulls on continuous chains of water molecules held together by cohesion.

Does temperature affect capillary action?

Yes. Warmer water has a lower surface tension and a slightly lower density, and the drop in surface tension matters more. So water rises a little less in a warm tube than in a cold one. Temperature also lowers viscosity, which lets the liquid reach its final height faster, even though that final height is somewhat smaller.

What is an easy capillary action experiment?

Fold a paper towel into a strip and hang it with one end in a glass of water mixed with a few drops of food coloring. Within minutes the color climbs the strip. Try strips of different papers or bridge two glasses with the strip to move water from a full glass into an empty one. Nothing hot or dangerous is needed.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.