Energy resources

Geothermal Energy

Geothermal energy is the thermal energy stored inside Earth, which people tap as hot water and steam to heat buildings and to drive turbines that generate electricity. The heat comes from the planet's formation and from radioactive decay in rocks. Unlike sunlight and wind, it is available day and night, but only a few places have it close to the surface.

Geothermal power station with steam plumes and pipelines crossing a volcanic valley, turning underground heat into electricity
Pipelines carry hot fluid from production wells to a geothermal power station built on a volcanic field.

At a Glance

Geothermal energy is heat from inside Earth, brought up as hot water or steam through wells. Power plants use it to spin turbines, and their efficiency is limited by the Carnot formula e = 1 - Tc/Th, so a 200 °C reservoir can convert at most about a third of the heat into work.

Energy form
Thermal energy (internal energy of hot rock and water)
Source of the heat
Earth's original heat plus radioactive decay
Key formula
eC = 1 − Tc/Th (maximum efficiency)
SI unit
joule (J) for energy, watt (W) for power
Renewable?
Yes, if heat is not drawn out faster than it is replaced
Main uses
Electricity, district heating, greenhouses, bathing
On this page
  1. What Is Geothermal Energy?
  2. Geothermal Energy Explained Simply
  3. Where Does Earth's Internal Heat Come From?
  4. How Do Geothermal Reservoirs Form?
  5. How Do Geothermal Power Plants Work?
  6. How Efficient Is Geothermal Power?
  7. Are Geothermal Heat Pumps the Same Thing?
  8. Where Is Geothermal Energy Used Today?
  9. What Are the Advantages and Disadvantages of Geothermal Energy?
  10. When Was Geothermal Energy First Used for Power?
  11. Practice Geothermal Energy Problems
  12. Common Misconceptions
  13. Key Facts
  14. Quiz
  15. FAQ

What Is Geothermal Energy?

Geothermal energy is heat that comes from beneath Earth's surface. The word joins the Greek roots for earth and heat. In physics terms it is thermal energy, the random motion of particles in hot rock and the water trapped inside it.

People use this heat in two broad ways. Direct use pipes hot water straight into homes, greenhouses, fish farms and pools. Geothermal power uses steam or very hot water to spin a turbine connected to an electric generator. Both depend on finding places where useful temperatures sit within reach of a drill.

Geothermal energy counts as a renewable energy source because Earth keeps producing heat for billions of years. A single reservoir can cool down if it is overused, though, so careful management matters.

Geothermal Energy Explained Simply

Think of Earth as a giant oven that has been warm since it formed and still has small heaters inside. Deep down it is extremely hot. Near the surface it is cool, but in some places hot rock lies close enough that rainwater seeping underground gets heated, sometimes to well above its normal boiling point.

A geothermal plant drills a hole into that hot water, lets it rush up as steam, uses the steam to spin a fan-like turbine, and then sends the cooled water back down to be heated again. Hot springs and geysers are the natural version of the same thing.

Where Does Earth's Internal Heat Come From?

Two sources keep the inside of Earth hot. The first is leftover heat from the planet's formation, when colliding rocks released huge amounts of energy and heavy iron sank to form the core. The second is radioactive decay of uranium, thorium and potassium in the crust and mantle, which releases energy continuously. Each source supplies a large share of the total, and both will last far longer than human civilization.

Temperature rises with depth. In typical continental crust it climbs by roughly 25 to 30 °C for every kilometer you descend, a pattern called the geothermal gradient. Near volcanoes, hot spots and plate boundaries, magma comes much closer to the surface and the gradient is far steeper.

Heat moves outward by conduction through solid rock and by the slow churning of the mantle. Conduction alone is gentle, as the worked example below shows, so useful geothermal sites are places where moving water has collected and concentrated the heat.

Example 3 Natural heat flow through a square kilometer

Rock with a thermal conductivity of 2.5 W/(m·K) lies under 1 km² (1,000,000 m²) of land. Temperature rises by 30 K over the top 1,000 m. How much heat flows up to the surface by conduction?

  1. Given:
    • thermal conductivity: k=2.5 W/(m·K)
    • cross-sectional area: A=1,000,000 m2
    • temperature difference across the slab: Th−Tc=30 K
    • thickness of the slab: d=1,000 m
  2. Formula: Qt=kA(Th−Tc)d
  3. Substitute: k=2.5 W/(m·K),A=1,000,000 m2,Th−Tc=30 K,d=1,000 m
  4. Answer: Q/t=75,000 W

Spread over a whole square kilometer, that trickle is far too weak to run a power plant, which is why plants drill into reservoirs where hot water has already gathered the heat.

Rock temperature at depth for two typical geothermal gradients (surface at 15 °C)
Depth (km)Gradient 25 °C/km (°C)Gradient 30 °C/km (°C)
01515
14045
26575
390105
4115135
5140165
Source: Computed as T = 15 °C + gradient × depth; gradients are typical continental values · Retrieved October 2026

How Do Geothermal Reservoirs Form?

A geothermal reservoir needs three things: a heat source, water and permeable rock. Rain and snowmelt soak down through cracks, reach hot rock, warm up and become less dense. The warm water rises back toward the surface while cooler water sinks to replace it, setting up a loop driven by convection.

If a layer of solid rock caps the reservoir, the hot water is trapped under pressure. Pressure raises the boiling point, so water deep in a reservoir can be far hotter than 100 °C and still be liquid. When a well opens a path upward, the pressure drops and part of that water flashes into steam.

Where the cap leaks, the hot water escapes naturally as hot springs, steaming vents, bubbling mud pools and geysers. These surface features often point engineers to the best places to drill.

Convection current diagram with warm water rising and cool water sinking, the circulation that concentrates heat in geothermal reservoirs
A convection loop like this one, scaled up through cracked rock, collects heat from a wide area and brings it toward the surface.

How Do Geothermal Power Plants Work?

Every geothermal power plant follows the same energy chain: thermal energy in the fluid becomes kinetic energy of a spinning turbine, and the generator turns that into electrical energy. Waste heat leaves through cooling towers. There are three main designs:

  • Dry steam plants use steam that comes straight out of the ground and send it directly through the turbine. Only a few fields produce steam this dry.
  • Flash steam plants take very hot pressurized water, drop its pressure so part of it boils instantly, and use that steam. This is the most common type.
  • Binary cycle plants pass moderately hot water through a heat exchanger that boils a second fluid with a lower boiling point. That fluid drives the turbine in a closed loop, so cooler reservoirs can still make electricity.

In most modern plants the cooled water is pumped back down injection wells. This keeps reservoir pressure up and stops dissolved minerals from reaching rivers.

Example 2 Heat delivered by a production well

A well brings up 80 kg of hot water every second. The plant cools it from 160 °C to 70 °C before pumping it back underground. Taking the specific heat of the water as about 4,200 J/(kg·K), how much thermal power does the plant extract?

  1. Given:
    • mdot: mdot=80 kg/s
    • c: c=4,200 J/(kg·K)
    • dT: dT=90 K
  2. Formula: P=m˙cΔT
  3. Substitute: mdot=80 kg/s,c=4,200 J/(kg·K),dT=90 K
  4. Answer: P=30,240,000 W

This is heat, not electricity. With a realistic conversion efficiency, only a fraction of it leaves the plant as electrical power.

How Efficient Is Geothermal Power?

A geothermal plant is a heat engine, so the second law of thermodynamics limits how much of its heat can become work. The ceiling is the Carnot efficiency, eC=1−Tc/Th, with both temperatures in kelvin. Because geothermal fluids are much cooler than the flames in a coal or gas boiler, this limit is fairly low.

The table shows the Carnot limit for several reservoir temperatures with heat rejected at 30 °C. Real geothermal plants typically turn roughly a tenth to a fifth of the heat they extract into electricity. That sounds poor, but the fuel is free and constantly renewed, so low efficiency mainly affects how many wells a plant needs.

The pressure-volume diagram below shows an ideal Carnot cycle between 453 K and 303 K. The enclosed area is the most work any engine could get per cycle between those temperatures.

Any power plant that turns heat into work is a heat engine, and this formula sets the upper limit on its efficiency from the hot and cold temperatures in kelvin.

eC=1−TcTh
What each symbol means
SymbolQuantitySI unit
eCmaximum (Carnot) efficiencydimensionless (1)
Tcabsolute temperature of the cold reservoirkelvin (K)
Thabsolute temperature of the hot reservoirkelvin (K)

Rearranged to find another variable:

Tc=Th(1−eC)Th=Tc1−eC

Valid for: reversible engine; temperatures MUST be in kelvin; upper limit for any real engine.

Example 1 The best a geothermal plant could do

A geothermal reservoir supplies fluid at 473.15 K (200 °C), and the plant's cooling towers reject heat at 298.15 K (25 °C). What is the maximum possible efficiency of a heat engine running between these temperatures?

  1. Given:
    • absolute temperature of the cold reservoir: Tc=298.15 K
    • absolute temperature of the hot reservoir: Th=473.15 K
  2. Formula: eC=1−TcTh
  3. Substitute: Tc=298.15 K,Th=473.15 K
  4. Answer: eC=0.3699

Real plants reach well below this ideal limit, because of friction, imperfect heat exchange and the fact that the fluid cools as it is used.

Maximum (Carnot) efficiency for different reservoir temperatures, heat rejected at 30 °C
Reservoir temperature (°C)Reservoir temperature (K)Carnot limit (%)
100373.1518.8
150423.1528.4
200473.1535.9
250523.1542.1
300573.1547.1
Source: Computed with e_C = 1 − T_c/T_h, T_c = 303.15 K · Retrieved October 2026
Pressure-volume diagram of an ideal Carnot cycle running between 453 K and 303 K, the efficiency ceiling for a geothermal plant
Between 453 K and 303 K, even an ideal engine converts only about a third of the heat it takes in.

Are Geothermal Heat Pumps the Same Thing?

Not quite. A ground-source heat pump, often sold as a geothermal heat pump, uses pipes buried a few meters down where the ground stays at a steady, mild temperature all year. In winter it moves heat from the ground into a building, and in summer it moves heat out of the building into the ground.

At those shallow depths most of the warmth actually comes from sunlight soaking into the soil, not from Earth's interior. The heat pump uses electricity to move heat rather than make it, which is why it can deliver several joules of heat for each joule of electricity. Our page on the refrigerator and heat pump explains the cycle.

Where Is Geothermal Energy Used Today?

Geothermal power is concentrated where plate boundaries and volcanoes bring heat near the surface. Iceland heats most of its homes with geothermal water and makes a large share of its electricity from it. The western United States, Indonesia, the Philippines, Kenya, Mexico, Turkey, Italy and New Zealand all run sizable geothermal fields.

Direct use is much more widespread, because lower temperatures are enough. Hot water from shallow wells warms greenhouses in cold climates, melts snow from sidewalks, dries timber and food, and fills public baths, a tradition thousands of years old in places such as Japan and ancient Rome.

Steaming turquoise hot spring with mineral terraces, a natural surface sign of geothermal heat close to the ground
Hot springs show where underground heat reaches the surface and often guide where geothermal wells are drilled.

What Are the Advantages and Disadvantages of Geothermal Energy?

Advantages:

  • It runs around the clock in all weather, unlike solar and wind power.
  • Plants take up little land for the energy they produce.
  • Greenhouse gas emissions are low compared with fossil fuel plants.
  • Once built, the running costs are small because there is no fuel to buy.

Disadvantages:

  • Good sites are limited to particular regions.
  • Exploration and drilling are expensive, and a well can turn out too cool or too dry.
  • Fluids can carry gases such as hydrogen sulfide, with its rotten-egg smell, and dissolved minerals that must be handled.
  • Injecting or removing fluid can trigger small earthquakes, and a reservoir drained too fast can cool off.

For a broader comparison of energy sources, see renewable vs nonrenewable energy.

When Was Geothermal Energy First Used for Power?

Hot springs have been used for bathing and cooking since prehistoric times. Generating electricity came much later. In 1904, at Larderello in Tuscany, Italy, natural steam was used to power a small generator that lit a handful of light bulbs, and a commercial geothermal power station followed there within about a decade.

New Zealand and the United States opened major plants in the mid twentieth century, and binary cycle technology later opened up cooler reservoirs. The physics behind all of them comes from nineteenth century thermodynamics, shaped by scientists such as Lord Kelvin, whose absolute temperature scale is the one you must use in the Carnot formula.

Practice Geothermal Energy Problems

Most geothermal problems combine two ideas: heat carried by water, Q=mcΔT, and the limit on turning heat into work. Try the specific heat calculator for the first, review energy efficiency for the second, and test yourself with our forms of energy worksheets. For other renewable sources, compare hydroelectric power and tidal and wave energy.

Common Misconceptions

Myth: Geothermal energy comes from the Sun heating the ground.

Physics: Deep geothermal heat comes from Earth's interior. Only the shallow ground used by heat pumps is warmed mainly by sunlight.

Myth: Geothermal energy can be used anywhere just by drilling.

Physics: Hot rock exists everywhere at depth, but economic sites need high temperatures at reachable depths plus water and permeable rock.

Myth: Geothermal plants are inefficient, so they waste fuel.

Physics: Their low efficiency comes from the Carnot limit at modest temperatures, and the heat they use is free and continually replaced.

Myth: A geothermal reservoir lasts forever no matter how hard it is used.

Physics: Pulling heat out faster than rock and water can replace it cools the reservoir, so output must be managed.

Key Facts

  • Geothermal energy is thermal energy from inside Earth, used for heating and for generating electricity.
  • Earth's internal heat comes from its formation and from the radioactive decay of uranium, thorium and potassium.
  • In typical continental crust, temperature rises by roughly 25 to 30 °C per kilometer of depth.
  • Geothermal power plants come in three main types: dry steam, flash steam and binary cycle.
  • The Carnot formula e = 1 − Tc/Th limits geothermal plants to modest efficiencies because their fluids are relatively cool.
  • Geothermal power runs day and night, giving a steady output that solar and wind cannot match on their own.
  • Cooled water is usually pumped back underground to keep the reservoir pressurized and productive.
Did you know? Water deep in a sealed geothermal reservoir can stay liquid at temperatures far above 100 °C, because the weight of the rock and water above raises its boiling point.

Quick Quiz: How Well Do You Know Geothermal Energy?

6 questions. Tap an answer to check it.

  1. What are the two main sources of Earth's internal heat?

  2. A reservoir is at 400 K and the cooling side is at 300 K. What is the Carnot efficiency limit?

  3. Which type of geothermal plant boils a second fluid in a closed loop?

  4. Why can water deep in a reservoir be hotter than 100 °C and still be liquid?

  5. Why is cooled geothermal water usually pumped back underground?

  6. What is a major advantage of geothermal power over solar power?

Frequently Asked Questions

What is geothermal energy in simple terms?

Geothermal energy is heat from inside Earth. Deep underground the rocks are hot, and in some places they heat water trapped in cracks to very high temperatures. People drill wells to bring that hot water or steam to the surface, then use it to warm buildings directly or to spin turbines that generate electricity. The cooled water is usually sent back down.

How does geothermal energy work to make electricity?

Wells bring hot water or steam up from an underground reservoir. In a flash plant, the pressure is lowered so some water boils into steam. The steam pushes on turbine blades, making them spin, and the turbine turns a generator that produces electricity. The steam is then condensed, and the water is pumped back underground to be reheated by the surrounding rock.

Is geothermal energy renewable?

Yes. Earth produces heat continuously through radioactive decay and still holds heat from its formation, and that supply will last billions of years. An individual reservoir can be overworked, though. If heat or water is removed faster than the surrounding rock can resupply it, the reservoir cools and output falls, so operators balance production with reinjection.

Why is geothermal energy not used everywhere?

Useful temperatures are usually too deep to reach cheaply except near volcanoes, hot spots and plate boundaries. A site also needs enough water and rock that lets it flow. Drilling deep wells is expensive and risky, since a well can come up too cool or too dry. Shallow ground-source heat pumps, however, can work almost anywhere.

What are three types of geothermal power plants?

Dry steam plants use steam taken directly from the ground. Flash steam plants take very hot pressurized water and lower its pressure so part of it turns to steam. Binary cycle plants pass moderately hot water through a heat exchanger that boils a second fluid with a low boiling point, which drives the turbine in a closed loop.

How hot is it inside Earth?

Temperature rises steadily with depth. A few kilometers down in ordinary crust, rocks are typically around 100 to 150 °C. The mantle is far hotter, and the core reaches several thousand degrees Celsius, comparable to the surface of the Sun. Geothermal plants only need to reach water at roughly 100 to 350 °C, which lies within a few kilometers in good locations.

Does geothermal energy cause earthquakes?

It can trigger small ones. Pumping fluid into rock or removing it changes the pressure on existing faults, and occasionally that lets them slip. Most of these quakes are too small to feel, but a few projects have caused noticeable shaking. Careful monitoring, slow injection rates and avoiding stressed faults lower the risk.

What is the difference between geothermal energy and a geothermal heat pump?

Geothermal power plants tap deep, very hot reservoirs heated by Earth's interior. A geothermal heat pump uses pipes only a few meters underground, where soil stays at a mild steady temperature mostly set by sunlight. The heat pump uses electricity to move heat into or out of a building, rather than producing power from the ground's heat.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.