Electricity from falling water

Hydroelectric Power

Hydroelectric power is electricity generated by letting water fall from a higher level to a lower one through a turbine, which spins a generator. The water's gravitational potential energy becomes kinetic energy and then electrical energy. It is the largest renewable source of electricity in the world, and a good plant converts about 90 percent of the water's energy into electricity.

Concrete hydroelectric dam in a mountain valley releasing white water from its base, with a calm reservoir behind it
A storage dam holds water high above the river so it can fall through turbines on demand.

At a Glance

Hydroelectric power is electricity made from moving water: water drops through a height called the head, spins a turbine, and the turbine turns a generator. The power available is about P = η ρ g Q h, where η is efficiency, ρ is water density, g is gravitational acceleration, Q is the flow rate and h is the head. More water or a bigger drop means more power.

Energy source
Gravitational potential energy of water (PE = mgh)
Power formula
P = η ρ g Q h (watts)
Main parts
Reservoir or intake, penstock, turbine, generator, transformer
Typical efficiency
About 85–92% for large modern turbines
Renewable?
Yes, the water cycle refills rivers and reservoirs
Depends on
Flow rate and head (height the water falls)
On this page
  1. What Is Hydroelectric Power?
  2. Hydroelectric Power Explained Simply
  3. How Does a Hydroelectric Dam Work?
  4. What Energy Changes Happen in a Hydro Plant?
  5. What Is the Formula for Hydroelectric Power?
  6. How Much Power Can Falling Water Produce?
  7. What Are the Types of Hydroelectric Power Plants?
  8. Where Is Hydroelectric Power Used?
  9. What Are the Advantages and Disadvantages of Hydropower?
  10. Who Invented Hydroelectric Power?
  11. Practice Energy Problems
  12. Common Misconceptions
  13. Key Facts
  14. Quiz
  15. FAQ

What Is Hydroelectric Power?

Hydroelectric power, often shortened to hydropower, is electricity produced from water that moves downhill. The water is guided through a turbine on its way down, and the spinning turbine drives a generator. Nothing is burned, so the plant itself releases no smoke or exhaust while it runs.

The idea is old. Water wheels ground grain and drove sawmills for centuries before anyone had heard of electricity. A modern hydro plant does the same basic job with far better engineering: a carefully shaped turbine, a sealed steel pipe and a generator that can feed a national grid.

Hydropower is a renewable energy source because the Sun keeps lifting water back uphill for free. Sunlight evaporates water from oceans and lakes, the vapor rises and cools, and rain or snow falls on high ground. Rivers then carry it back down, and a hydro plant takes a share of that energy on the way.

Hydroelectric Power Explained Simply

Picture a bucket of water on a high shelf. If you tip it over a small paddle wheel, the falling water pushes the paddles around. Now imagine the shelf is a mountain lake and the paddle wheel is the size of a house. That is a hydroelectric plant.

Two things decide how much electricity you get. The first is how much water flows each second. The second is how far it falls. A huge river with a short drop and a thin stream with a very tall drop can both make plenty of power.

The generator does the final step. Inside it, magnets spin past coils of wire, and that motion pushes electric charges along the wire. So the chain is simple: height, then speed, then spin, then electricity.

How Does a Hydroelectric Dam Work?

A conventional hydro plant follows the same path every time the water moves through it:

  1. Store. A dam blocks a river and builds up a reservoir. The water surface now sits far above the river below the dam.
  2. Intake. Gates near the bottom of the reservoir open, and screens keep out logs and debris.
  3. Penstock. The water rushes down a large sealed pipe called a penstock. It loses height and gains speed and pressure.
  4. Turbine. The water strikes or flows through curved blades and sets the turbine shaft spinning.
  5. Generator. The shaft turns the rotor of an electric generator, where electromagnetic induction produces an alternating current.
  6. Transformer and lines. A transformer raises the voltage so the power can travel long distances with small losses.
  7. Tailrace. The slowed water leaves through a channel and rejoins the river downstream.

Operators control the output by opening or closing wicket gates in front of the turbine. More water through the gates means more torque on the shaft and more power to the grid.

Turbine hall of a hydroelectric power station with a row of large round generator housings under an overhead crane
Each round housing covers a generator driven by a water turbine on the level below.

What Energy Changes Happen in a Hydro Plant?

A hydro plant is a clean example of an energy transformation chain. Water held at height has gravitational potential energy. As it drops down the penstock, that store empties and the water's kinetic energy grows. The turbine then takes the kinetic energy and pressure of the water and turns it into rotational kinetic energy of the shaft. Finally, the generator converts the rotation into electrical energy.

No step is perfect. Friction between water and the pipe walls warms the water very slightly, and bearings, gears and wire resistance lose a little more as heat and sound. The energy bars below follow 1 kg of water down a 50 m drop, with 6 percent of its energy lost to friction before it reaches the turbine.

Energy bar chart for 1 kg of water falling 50 m, potential energy turning into kinetic energy with a small thermal loss, total 490.5 J
As water drops down the penstock, potential energy becomes kinetic energy, and a small share warms the water through friction.

What Is the Formula for Hydroelectric Power?

Start with the energy of the stored water. A mass m held a height h above the turbine stores PEg=mgh. A plant does not release one block of water, though; it passes a steady stream. If a volume Q of water flows each second and water has density ρ, then the mass per second is ρQ.

Multiply that mass rate by g and h and you get the energy delivered per second, which is power. Real equipment converts only a fraction η of that energy, so the working formula is P=ηρgQh. With Q in cubic meters per second and h in meters, P comes out in watts.

In this formula h is the net head: the vertical drop from the reservoir surface to the turbine, minus the small amount of head lost to friction in the pipes. For more energy equations in one place, see our energy formulas sheet, and use the potential energy calculator to check the stored energy for any mass and height.

Every hydro calculation starts from the energy stored in raised water, so here is the potential energy formula with its variables and SI units.

PEg=mgh
What each symbol means
SymbolQuantitySI unit
PEggravitational potential energyjoule (J)
mmasskilogram (kg)
gacceleration due to gravity (9.80 m/s² (standard 9.80665 m/s²))meter per second squared (m/s²)
hheight above the chosen reference levelmeter (m)

Rearranged to find another variable:

m=PEgghh=PEgmgg=PEgmh

Valid for: near Earth's surface (uniform g); only changes in PE are physically meaningful.

Example 1 Energy in one cubic meter of reservoir water

One cubic meter of water has a mass of about 1,000 kg. If it sits in a reservoir 120 m above the turbines, how much gravitational potential energy does it store?

  1. Given:
    • mass: m=1,000 kg
    • height above the chosen reference level: h=120 m
  2. Formula: PEg=mgh
  3. Substitute: PEg=(1,000 kg)(9.81 m/s2)(120 m)
  4. Answer: PEg=1,177,200 J (1.177 MJ)

Over a megajoule per cubic meter sounds large, but a kilowatt-hour is 3.6 MJ, so a plant has to move enormous volumes of water every second.

Example 2 Output of a mid-sized river plant

A river plant sends 25 m³ of water per second through turbines with a 60 m head. The turbines and generators together are 90% efficient. What electrical power does the plant deliver? Use P = η ρ g Q h with water density 1,000 kg/m³.

  1. Given:
    • η: η=0.9
    • ρ: ρ=1,000 kg/m3
    • g: g=9.81 m/s2
    • Q: Q=25 m3/s
    • h: h=60 m
  2. Formula: P=ηρgQh
  3. Substitute: η=0.9,ρ=1,000 kg/m3,g=9.81 m/s2,Q=25 m3/s,h=60 m
  4. Answer: P=13,243,500 W

That is roughly 13 megawatts, enough on average for several thousand homes.

How Much Power Can Falling Water Produce?

The formula shows that power grows in a straight line with both flow and head. Double the head and you double the power; double the flow and you double it again. The table below fixes the flow at one cubic meter per second and the efficiency at 90 percent, then changes only the head.

A useful rule of thumb follows from it. Each cubic meter of water falling 100 m releases about 0.27 kWh, so a plant needs millions of cubic meters a day to supply a city. That is why big plants sit on large rivers or very tall dams. To turn power into energy, multiply it by the running time, or use our power calculator.

Example 3 How much flow does a small plant need?

A town wants a 500,000 W small hydro plant on a stream with a 12 m drop. If the equipment is 85% efficient, what volume flow rate must pass through the turbine? Use Q = P / (η ρ g h).

  1. Given:
    • P: P=500,000 W
    • η: η=0.85
    • ρ: ρ=1,000 kg/m3
    • g: g=9.81 m/s2
    • h: h=12 m
  2. Formula: Q=Pηρgh
  3. Substitute: P=500,000 W,η=0.85,ρ=1,000 kg/m3,g=9.81 m/s2,h=12 m
  4. Answer: Q=4.997 m3/s

A low head forces a large flow, which is why low-head plants use wide, slow turbines.

Electrical power from a flow of 1 m³/s at different heads (90% efficiency)
Head (m)Head (ft)Power (kW)Typical setting
51644.1Low weir on a lowland river
103388.3Run-of-river canal
2582220.7Small valley dam
50164441.5Medium dam
100328882.9Large dam
2006561,765.8Tall dam or mountain penstock
5001,6404,414.5Alpine plant with impulse turbines
Source: Computed with P = ηρgQh, η = 0.9, ρ = 1,000 kg/m³, g = 9.81 m/s², Q = 1 m³/s · settings are typical examples · Retrieved October 2026

What Are the Types of Hydroelectric Power Plants?

  • Impoundment (storage) plants use a dam and a large reservoir. They can store water for weeks or months and release it when demand is high.
  • Run-of-river plants divert part of a river through a channel or pipe with little or no storage. They disturb the river less but their output follows the season.
  • Pumped storage plants work like a giant rechargeable battery. When electricity is cheap and plentiful, they pump water uphill into an upper reservoir; when demand peaks, they let it fall back through the turbines. Typically 70 to 80 percent of the energy used for pumping comes back.
  • Small, mini and micro hydro systems range from a few kilowatts on a farm stream to a few megawatts for a town.

Turbines are chosen to match the site. Impulse turbines, with spoon-shaped buckets hit by a fast jet, suit tall heads with modest flow. Reaction turbines, which sit fully inside the flowing water, suit medium and low heads with large flow. The nozzle diagram below shows how a jet gets its speed: the same flow squeezed through a smaller opening must move faster.

Pipe narrowing from 2 m² to 0.25 m² showing water speeding up from 3 m/s to 24 m/s, like a hydro turbine nozzle
The same flow squeezed through a smaller nozzle must move faster, which creates the fast jet that drives an impulse turbine.

Where Is Hydroelectric Power Used?

Hydropower supplies about 15 percent of the world's electricity, and for many decades it produced more than all other renewable sources combined. Some countries with steep terrain and heavy rain or snow, such as Norway and Paraguay, get nearly all of their electricity from it.

The largest plant ever built, the Three Gorges Dam on the Yangtze River in China, has an installed capacity of about 22,500 megawatts. The Hoover Dam on the Colorado River, finished in the 1930s, has about 2,000 megawatts. At the other end of the scale, a family cabin can run lights and a fridge from a micro turbine on a stream with just a few meters of drop.

Tidal barrages use a related idea, trapping seawater behind a barrier and releasing it through turbines as the tide falls. Read more on our tidal and wave energy page.

What Are the Advantages and Disadvantages of Hydropower?

Advantages. Hydro plants produce no direct emissions, run for many decades and have very low fuel costs because the fuel is rain. They can ramp from standby to full output in minutes, which helps balance the grid when solar and wind output changes. Reservoirs can also supply drinking water, irrigation and flood control.

Disadvantages. Dams are expensive and slow to build. Flooding a valley can displace communities and destroy habitat, and a dam blocks fish that migrate upstream to spawn. Rotting plants in new reservoirs can release methane, and droughts cut output when the reservoir level falls.

For how hydro compares with fuels that run out, see renewable vs nonrenewable energy, and for the other big renewables, read about wind energy and solar energy.

Who Invented Hydroelectric Power?

No single person invented it. Water wheels are ancient, and engineers in the 1800s improved them into efficient turbines. The missing piece was the generator, which rests on the discovery of electromagnetic induction by Michael Faraday in 1831.

Once practical generators existed, hydro plants followed quickly. Small plants supplying electric lighting appeared in the early 1880s in both Britain and the United States, and large stations at Niagara Falls in the 1890s showed that alternating current could carry hydropower to distant cities.

Practice Energy Problems

Hydropower problems are really potential energy and power problems in disguise. Build the skills with our forms of energy worksheets, then check each answer with the potential energy calculator. When you are ready, take the short quiz below.

Common Misconceptions

Myth: Dams create energy by storing water.

Physics: A dam only stores energy that the Sun already put into the water by lifting it as vapor. The plant converts that stored potential energy into electricity.

Myth: Only the amount of water matters, not the height.

Physics: Power depends on flow and head equally. A small flow falling a long way can match a big flow falling a short way.

Myth: Hydropower uses up the water.

Physics: The water passes through the turbine and returns to the river. It loses height and some speed, but none of it is consumed.

Myth: Hydroelectric power has no environmental effects because it is renewable.

Physics: It has no smokestack, but dams change river flow, block migrating fish and can flood large areas of land.

Key Facts

  • Hydroelectric power converts the gravitational potential energy of water into electricity using a turbine and a generator.
  • The power of a hydro plant is about P = ηρgQh, so it rises in proportion to both the flow rate and the head.
  • Large modern hydro turbines convert roughly 85 to 92 percent of the water's energy into electricity.
  • Pumped storage plants store surplus electricity by pumping water uphill and return about 70 to 80 percent of it later.
  • Hydropower supplies about 15 percent of the world's electricity and is the largest renewable source of it.
  • The generator inside every hydro plant works by electromagnetic induction, discovered by Michael Faraday in 1831.
  • Hydro plants can change output within minutes, which helps balance grids that also use wind and solar power.
Did you know? Water leaving a tall mountain penstock through a nozzle can reach speeds over 100 m/s, so impulse turbine buckets are made of tough stainless steel to survive the constant blast.

Quick Quiz: How Well Do You Know Hydroelectric Power?

6 questions. Tap an answer to check it.

  1. What form of energy does water in a high reservoir mainly store?

  2. In P = ηρgQh, what does Q stand for?

  3. If the head of a hydro plant doubles while the flow stays the same, the power output

  4. Which part of a hydro plant actually produces the electric current?

  5. What does a pumped storage plant do when electricity is plentiful?

  6. Which is a real disadvantage of large dams?

Frequently Asked Questions

How does hydroelectric power work step by step?

Water is stored at a height behind a dam or diverted from a river. It flows down a sealed pipe called a penstock, gaining speed and pressure. The moving water spins a turbine, the turbine shaft turns a generator, and the generator produces electricity through electromagnetic induction. A transformer raises the voltage for the power lines, and the water flows back into the river below the plant.

What type of energy does hydroelectric power use?

It starts with gravitational potential energy, the energy water has because it is raised above the turbine. As the water falls, that becomes kinetic energy. The turbine turns it into rotational kinetic energy, and the generator turns the rotation into electrical energy. Ultimately the energy came from the Sun, which evaporated the water and lifted it to high ground as rain or snow.

Is hydroelectric power renewable?

Yes. The water cycle, driven by sunlight, keeps refilling rivers and reservoirs, so the energy source does not run out the way coal or natural gas does. Hydropower can still be limited locally by long droughts, by silt slowly filling reservoirs, and by the shrinking number of good river sites that have not already been dammed.

How efficient is hydroelectric power?

Large modern hydro turbines and generators usually convert about 85 to 92 percent of the water's available energy into electricity. That is far higher than fuel-burning power plants, which lose most of their energy as waste heat. Small plants and older equipment tend to be somewhat less efficient, often in the 60 to 80 percent range.

What are the main disadvantages of hydroelectric power?

Building a large dam is very costly and can take years. The reservoir may flood farmland, forests and towns, forcing people to move. Dams block fish migration and change water temperature and sediment downstream. In dry years output can fall sharply, and new reservoirs can release methane from decaying plants. Good sites are also limited to places with enough flow and height.

How much electricity does a hydroelectric dam produce?

It depends on flow and head. A micro hydro system on a stream may produce a few kilowatts, enough for one home. A medium dam might produce tens of megawatts, while the largest plants reach thousands of megawatts. You can estimate any plant with P = ηρgQh, multiplying efficiency, water density, gravitational acceleration, flow rate and head.

What is the difference between a dam and run-of-river hydropower?

A dam plant builds a large reservoir, which lets it store water and choose when to generate. A run-of-river plant diverts part of the natural flow through a turbine with little or no storage, so its output rises and falls with the river. Run-of-river plants flood much less land but cannot hold water back for dry periods.

What is pumped storage hydropower?

Pumped storage uses two reservoirs at different heights. When there is spare electricity, pumps move water up to the higher reservoir, storing it as potential energy. When demand rises, the water flows back down through turbines and generates power again. It acts like a huge battery for the grid, returning roughly 70 to 80 percent of the energy used to pump.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.