Inductors in circuits

RL Circuits

An RL circuit is a circuit containing a resistor and an inductor, in which the current cannot change instantly but rises or falls smoothly with a time constant equal to the inductance divided by the resistance. After one time constant the current has covered about 63 percent of its change, and after five it has essentially settled.

Copper coil, resistor and switch wired together on a desk, the parts of a simple RL circuit
A coil, a resistor and a switch are all you need to see current rise and fall with a time constant.

At a Glance

In an RL circuit the time constant is τ = L / R, with L in henries and R in ohms giving τ in seconds. When a DC supply is switched on, the current grows as I = I0(1 - e^(-t/τ)), where I0 = V/R; when the supply is removed and the current has a path, it decays as I = I0 e^(-t/τ).

Time constant
τ = L/R (seconds)
Final current
I0 = V/R
Current growth
I = I0(1 − e−t/τ)
Current decay
I = I0e−t/τ
After one τ
63.2% of the change is complete
Energy stored
U = ½LI² in the inductor's magnetic field
On this page
  1. What Is an RL Circuit?
  2. RL Circuits Explained Simply
  3. What Happens When You Switch On an RL Circuit?
  4. What Is the Time Constant of an RL Circuit?
  5. What Happens When the Current Is Switched Off?
  6. How Do the Voltages Change in an RL Circuit?
  7. How Are RL Circuits Different From RC Circuits?
  8. How Can You Measure the Time Constant?
  9. Where Are RL Circuits Used?
  10. Going Deeper: Where Does the Exponential Come From?
  11. Practice RL Circuit Problems
  12. Common Misconceptions
  13. Key Facts
  14. Quiz
  15. FAQ

What Is an RL Circuit?

An RL circuit is any circuit built from resistance (R) and inductance (L). The simplest version has a battery, a switch, a resistor and a coil in a single series loop. Real coils always have some resistance in their wire, so every inductor connected to a supply already forms a small RL circuit.

The interesting part is timing. Flip the switch on a plain resistor and the current jumps to its final value instantly. Add an inductor and the current climbs gradually instead, following a smooth curve. Open the circuit and the inductor fights to keep the current flowing. Those slow changes, set by the ratio L/R, are what make RL circuits useful.

Series RL circuit diagram with a 12 V battery, a switch, a 60 ohm resistor and a 0.3 H inductor
The steady current is V/R = 0.2 A; the inductor (drawn as a block) only controls how fast it gets there.

RL Circuits Explained Simply

Think of an inductor as a heavy flywheel attached to the flow of current. A flywheel is hard to spin up and hard to stop. When you start pushing, it speeds up slowly; when you stop pushing, it keeps turning for a while.

The resistor is like friction on that flywheel. With more friction, the wheel reaches its top speed sooner, because that top speed is lower. With a heavier wheel, meaning a bigger inductance, everything takes longer. The time constant L/R captures that balance in a single number of seconds.

What Happens When You Switch On an RL Circuit?

The moment the switch closes, the current is zero and starts to rise. A changing current makes the coil's magnetic field change, and by Faraday's law that changing field induces a voltage in the coil itself. Lenz's law says this induced voltage opposes the change, so at first it pushes back against almost the whole supply voltage.

As the current rises, it changes more slowly, the coil's opposing voltage shrinks, and more of the supply voltage appears across the resistor. The current follows I=I0(1−e−t/τ), approaching the final value I0=V/R that it would have with no coil at all. The graph shows this rise for a 0.3 H coil and 60 Ω on a 12 V supply.

Graph of RL circuit current rising toward 0.2 A and a second curve falling from 0.2 A, both with a 5 ms time constant
Rise and decay follow mirror-image curves with the same time constant.

What Is the Time Constant of an RL Circuit?

The time constant is τ=L/R. It tells you how quickly the circuit responds: after one time constant the current has completed 63.2% of its change, after two about 86.5%, and after five more than 99%. Engineers usually treat five time constants as "fully settled".

The units work out neatly. One henry is one volt-second per ampere, and one ohm is one volt per ampere, so henries divided by ohms leave seconds. A large inductance or a small resistance makes the circuit slow. A small inductance or a large resistance makes it fast.

The table lists the current at each multiple of τ for the 12 V, 60 Ω, 0.3 H circuit, both rising after switch-on and falling after switch-off.

Here is the RL time constant with each variable and its SI unit, plus the forms for finding L or R.

τ=LR
What each symbol means
SymbolQuantitySI unit
τtime constantsecond (s)
Linductancehenry (H)
Rresistanceohm (Ω)

Rearranged to find another variable:

L=τRR=Lτ

Valid for: current reaches ≈ 63.2% of its final value after one τ.

Example 1 Time constant of a relay coil circuit

A relay coil with an inductance of 0.3 H is connected in series with a total resistance of 60 Ω to a 12 V supply. What is the time constant of the circuit?

  1. Given:
    • inductance: L=0.3 H
    • resistance: R=60 Ω
  2. Formula: τ=LR
  3. Substitute: L=0.3 H,R=60 Ω
  4. Answer: τ=0.005 s

That is a few milliseconds, so the current reaches about 99% of its final 0.2 A within roughly five times this value.

Current in an RL circuit (V = 12 V, R = 60 Ω, L = 0.3 H, τ = 5 ms) at multiples of the time constant
TimeRise: % of finalRise: current (A)Decay: % of startDecay: current (A)
1τ = 5 ms63.2%0.12636.8%0.074
2τ = 10 ms86.5%0.17313.5%0.027
3τ = 15 ms95.0%0.1905.0%0.010
4τ = 20 ms98.2%0.1961.8%0.004
5τ = 25 ms99.3%0.1990.7%0.001
Source: Computed with I = I0(1 − e^(−t/τ)) and I = I0 e^(−t/τ), I0 = V/R = 0.2 A · Retrieved October 2026

What Happens When the Current Is Switched Off?

If the supply is removed but the coil still has a closed path through a resistor, the current does not stop at once. It dies away as I=I0e−t/τ, with the same time constant. The energy stored in the coil's magnetic field, U=12LI2, is turned into heat in the resistor along the way.

If instead you simply break the circuit, there is no path at all. The current must fall almost instantly, so ΔI/Δt becomes huge, and the coil's induced voltage, ε=−LΔI/Δt, can leap to hundreds or thousands of volts. That is why you sometimes see a spark at a switch that controls a motor or relay. Circuits protect against this with a flyback diode across the coil, which gives the current a gentle path to decay.

Example 2 Choosing a resistor for a faster response

A designer needs a 0.05 H coil to respond with a time constant of 0.002 s. What total series resistance gives that time constant?

  1. Given:
    • time constant: τ=0.002 s
    • inductance: L=0.05 H
  2. Formula: R=Lτ
  3. Substitute: τ=0.002 s,L=0.05 H
  4. Answer: R=25 Ω

More resistance makes the circuit faster, but it also lowers the final current V/R, so the supply voltage often has to rise to compensate.

How Do the Voltages Change in an RL Circuit?

Kirchhoff's loop rule says the supply voltage is shared between the resistor and the coil at every instant: V=IR+LdIdt. Right after switch-on, the current is zero, so the resistor gets no voltage and the coil takes all of it. As time passes the shares swap.

The resistor's voltage, VR=IR, rises along the same curve as the current. The coil's voltage, VL=Ve−t/τ, starts at the full supply value and fades toward zero. Once the current is steady, an ideal coil acts like a plain wire. Our page on Kirchhoff's laws explains the loop rule used here.

How Are RL Circuits Different From RC Circuits?

RL and RC circuits share the same exponential curves and the same 63.2% rule, but they swap roles. In an RC circuit the capacitor's voltage cannot jump, and the current is largest at the start. In an RL circuit the inductor's current cannot jump, and the coil's voltage is largest at the start.

Their time constants also respond to resistance in opposite ways. Raising R slows an RC circuit, because τ=RC, but speeds up an RL circuit, because τ=L/R. The comparison table below lays out the full set of differences.

RL circuits compared with RC circuits
FeatureRL circuitRC circuit
Energy storageMagnetic field of the coil, ½LI²Electric field of the capacitor, ½CV²
Time constantτ = L/Rτ = RC
Effect of larger RFaster responseSlower response
Quantity that cannot jumpCurrent through the coilVoltage across the capacitor
Right after switch-onCurrent zero, coil voltage maximumCapacitor voltage zero, current maximum
Steady DC stateCoil acts like a wireCapacitor acts like a break
As a simple filterSeries coil passes low frequenciesSeries capacitor passes high frequencies
Source: Derived from τ = L/R, τ = RC and the loop rule · Retrieved October 2026

How Can You Measure the Time Constant?

Feed the circuit a square wave from a signal generator and watch the voltage across the resistor on an oscilloscope. Each time the square wave steps up, the trace rises along a curve; each time it steps down, the trace falls. Measure the time for the trace to reach 63% of its final height and you have τ.

Another trick uses the half-way point. The current reaches 50% of its final value after about 0.693τ, since ln⁡2≈0.693. With the resistance known, L=τR gives the coil's inductance, measured in henries.

Example 3 Finding an unknown inductance

A student times the current in a coil-and-resistor circuit on an oscilloscope and finds a time constant of 0.012 s. The total resistance is 150 Ω. What is the inductance of the coil?

  1. Given:
    • time constant: τ=0.012 s
    • resistance: R=150 Ω
  2. Formula: L=τR
  3. Substitute: τ=0.012 s,R=150 Ω
  4. Answer: L=1.8 H

This is a quick way to measure inductance with only a resistor, a square-wave source and an oscilloscope.

Where Are RL Circuits Used?

Every relay, solenoid valve, electric door lock and motor winding is an RL circuit, so its time constant limits how fast it can switch. Car ignition systems used the opposite effect for decades: a coil's current was interrupted suddenly, and the voltage spike, stepped up by a second winding, fired the spark plug.

In AC and audio electronics, RL combinations act as filters. A coil passes slowly changing signals easily but resists fast ones, so a series coil feeding a resistor lets low frequencies through and blocks high ones. Loudspeaker crossovers use this to steer bass notes to the woofer. To see how a coil's opposition grows with frequency, read about reactance and impedance.

Clear relay showing its copper coil and contacts, a component whose switching speed is set by its RL time constant
A relay coil is an RL circuit, so its current, and its pull on the contacts, builds up over a few time constants.

Going Deeper: Where Does the Exponential Come From?

Rearranging the loop rule gives dIdt=V−IRL. The rate of change of the current is proportional to how far the current still is from its final value V/R. Any quantity that approaches a target at a rate proportional to the remaining gap follows an exponential curve, the same math behind cooling coffee and charging capacitors.

Solving the equation gives I=VR(1−e−Rt/L), which is the growth curve with τ=L/R. Add a capacitor to the loop and the equation gains a new term, which can make the current oscillate instead; that is the subject of RLC circuits. The American physicist Joseph Henry studied self-induction in coils in the 1830s, and the unit of inductance is named after him.

Practice RL Circuit Problems

Build and test virtual circuits with our circuit simulator, then work through printable problems with answer keys in the electricity worksheets. The worked examples on this page and the quiz below cover the time constant in all three directions: finding τ, R and L.

Common Misconceptions

Myth: An inductor blocks direct current.

Physics: An ideal inductor only resists changes in current. Once a DC current is steady, the coil acts like a plain wire and the current is set by the resistance alone.

Myth: Adding resistance always slows a circuit down.

Physics: In an RL circuit the time constant is L/R, so more resistance gives a shorter time constant and a faster response, though a smaller final current.

Myth: The current in an RL circuit stops the instant the switch opens.

Physics: The inductor keeps current flowing for a while. If there is no path, it forces one, often as a spark across the switch contacts.

Myth: After one time constant the current has reached its final value.

Physics: After one time constant it has only reached about 63% of its final value. It takes about five time constants to get within 1%.

Key Facts

  • An RL circuit contains a resistor and an inductor, and its current changes gradually rather than instantly.
  • The time constant of an RL circuit is τ = L/R, measured in seconds.
  • After one time constant the current has completed 63.2% of its change; after five, over 99%.
  • When switched on, the current grows as I = I0(1 − e^(−t/τ)) toward I0 = V/R.
  • When the supply is removed and a path remains, the current decays as I = I0 e^(−t/τ).
  • Breaking an inductive circuit suddenly can create a large voltage spike, which flyback diodes prevent.
  • Increasing resistance makes an RL circuit respond faster, the opposite of an RC circuit.
Did you know? For much of the 20th century, gasoline cars made their spark plug voltage with an RL circuit: interrupting the current in an ignition coil produced a jolt of many thousands of volts from a 12 V battery.

Quick Quiz: How Well Do You Know RL Circuits?

6 questions. Tap an answer to check it.

  1. What is the time constant of an RL circuit with L = 0.4 H and R = 20 Ω?

  2. After one time constant of switch-on, the current in an RL circuit has reached about what fraction of its final value?

  3. What happens to the time constant of an RL circuit if the resistance doubles?

  4. Right after the switch closes in a DC RL circuit, where is almost all of the supply voltage?

  5. What does a flyback diode across a relay coil do?

  6. In steady DC operation, an ideal inductor behaves like…

Frequently Asked Questions

What is an RL circuit?

An RL circuit is a circuit made of a resistor and an inductor, connected in series or parallel to a source. Because the inductor opposes changes in current, the current in an RL circuit rises and falls gradually instead of jumping. The speed of those changes is set by the time constant L/R. RL circuits appear in relays, motors, filters and power supplies.

What is the time constant of an RL circuit?

The time constant is τ = L/R, the inductance in henries divided by the resistance in ohms, which gives a time in seconds. It is the time for the current to complete about 63.2% of its change after a switch is flipped. A 0.3 H coil with 60 Ω, for example, has a time constant of 5 milliseconds.

Why does current rise slowly in an RL circuit?

When current starts to flow, the coil's magnetic field begins to build. That changing field induces a voltage in the coil that opposes the change, as Lenz's law predicts. This back voltage starts out equal to the supply voltage and shrinks as the current approaches its final value, so the current rises along a smooth exponential curve.

What is the formula for current in an RL circuit?

When a DC source of voltage V is switched on, the current is I = (V/R)(1 − e^(−t/τ)), with τ = L/R. When the source is removed and the coil discharges through a resistor, the current is I = I0 e^(−t/τ), where I0 is the current at the moment of switching. Both curves use the same time constant.

How long does it take for an RL circuit to reach steady state?

In theory the current never quite reaches its final value, because the exponential only approaches it. In practice, after five time constants the current is within about 0.7% of the final value, so engineers treat 5τ as fully settled. For a circuit with τ = 2 ms, that means about 10 ms.

Why is there a spark when you open a circuit with a coil?

An inductor resists any sudden change in current. Opening a switch tries to drop the current to zero almost instantly, so the coil produces a very large voltage to keep the current going. That voltage can ionize the air between the switch contacts, creating a spark. A diode placed across the coil gives the current a safe path and prevents it.

How does an RL circuit act as a filter?

An inductor's opposition to AC, its reactance, rises with frequency. In a series coil feeding a resistor, low-frequency signals pass the coil easily and appear across the resistor, while high-frequency signals are mostly blocked. This makes a low-pass filter, used in speaker crossovers and power supplies to smooth out fast ripples.

What is the difference between an RL and an RC circuit?

Both have exponential responses with a time constant, but an RL circuit stores energy in a magnetic field while an RC circuit stores it in an electric field. In an RL circuit the current cannot jump and τ = L/R; in an RC circuit the capacitor voltage cannot jump and τ = RC. More resistance speeds up an RL circuit but slows an RC circuit.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.