Resistor plus capacitor

RC Circuits

An RC circuit is a circuit containing a resistor and a capacitor, in which the capacitor charges or discharges gradually rather than instantly. The pace is set by the time constant τ = RC: after one time constant a charging capacitor reaches about 63% of its final voltage. RC circuits time blinking lights, smooth power supplies and filter signals.

Breadboard with a capacitor, a resistor and a glowing LED, a simple RC timing circuit on a workbench
A resistor, a capacitor and a light are enough to build an RC timer that fades the LED slowly.

At a Glance

An RC circuit is a resistor and capacitor connected so that the capacitor charges or discharges through the resistor. Its time constant is τ = R C, in seconds when R is in ohms and C in farads. A charging capacitor follows V = ε(1 − e^(−t/RC)) and reaches about 63% of the supply voltage after one τ; a discharging one follows V = V0 e^(−t/RC).

Symbol
τ (time constant)
SI unit
second (s); 1 Ω × 1 F = 1 s
Formula
τ = RC
Charging
V = ε(1 − e−t/RC)
Discharging
V = V₀e−t/RC
Rule of thumb
About 5τ to fully charge or discharge
On this page
  1. What Is an RC Circuit?
  2. RC Circuits Explained Simply
  3. What Is the Time Constant of an RC Circuit?
  4. How Does a Capacitor Charge in an RC Circuit?
  5. How Does a Capacitor Discharge Through a Resistor?
  6. How Much Does a Capacitor Charge After Each Time Constant?
  7. Where Does the Energy Go in an RC Circuit?
  8. What Are RC Circuits Used For?
  9. How Are RC Circuits Related to Other Circuits?
  10. Practice RC Circuit Problems
  11. Common Misconceptions
  12. Key Facts
  13. Quiz
  14. FAQ

What Is an RC Circuit?

An RC circuit is any circuit built around a resistor (R) and a capacitor (C). The simplest version puts a battery, a switch, a resistor and a capacitor in one loop. Close the switch and the capacitor fills with charge, but not instantly: the resistor limits how fast current can flow onto its plates.

The result is a voltage that changes smoothly over time instead of jumping. The capacitor voltage rises quickly at first, then slower and slower as it approaches the battery voltage. Disconnect the battery and let the capacitor drain through the resistor, and the voltage falls in the mirror-image way.

This gradual, predictable change is the whole point. It turns a resistor and a capacitor into a timer, a filter or a smoothing device, which is why RC circuits appear in nearly every electronic product.

Series RC circuit with a 9 V battery, a switch, a 10 kilohm resistor and a 220 microfarad capacitor in one loop
The basic RC circuit: when the switch closes, current through R charges C, with τ = RC = 2.2 s.

RC Circuits Explained Simply

Think of filling a balloon with air through a thin straw. The balloon is the capacitor, the straw is the resistor, and your lungs are the battery. At first air rushes in easily. As the balloon fills, it pushes back harder, and the flow slows to a trickle.

A wider straw (smaller resistance) fills the balloon faster. A bigger balloon (larger capacitance) takes longer to fill. Multiply the two together and you get one number, the time constant, that tells you how slow the whole process is. Letting the air out through the same straw follows the same pattern in reverse.

What Is the Time Constant of an RC Circuit?

The time constant is τ=RC, the resistance in ohms times the capacitance in farads. The answer comes out in seconds, because one ohm times one farad equals one second. It is the natural time scale of the circuit: everything that happens in an RC circuit is measured in multiples of τ.

After one time constant, a charging capacitor has reached about 63.2% of its final voltage, and a discharging capacitor has fallen to about 36.8% of its starting voltage. After five time constants it is within 1% of the end point, so engineers treat 5τ as "fully charged" or "fully discharged."

Doubling either R or C doubles the time constant. That gives designers two independent knobs: pick a convenient capacitor, then choose the resistor that gives the timing you need.

Here is the time constant formula with each variable and its SI unit, plus the forms for finding resistance or capacitance.

τ=RC
What each symbol means
SymbolQuantitySI unit
τtime constantsecond (s)
Rresistanceohm (Ω)
Ccapacitancefarad (F)

Rearranged to find another variable:

R=τCC=τR

Valid for: after one τ a charging capacitor reaches ≈ 63.2% of its final voltage.

Example 1 Time constant of a timing circuit

A timing circuit uses a 47 kΩ resistor (47,000 Ω) and a 100 μF capacitor (1.00 × 10⁻⁴ F). What is its time constant?

  1. Given:
    • resistance: R=47,000 Ω
    • capacitance: C=1×10−4 F
  2. Formula: τ=RC
  3. Substitute: R=47,000 Ω,C=1×10−4 F
  4. Answer: τ=4.7 s

Kiloohms times microfarads is a handy combination: the answer comes out in a few seconds, perfect for human-scale delays.

How Does a Capacitor Charge in an RC Circuit?

When the switch closes on an uncharged capacitor, the capacitor voltage starts at zero, so the full battery voltage sits across the resistor and the current is at its largest, I0=ε/R. As charge builds up, the capacitor voltage grows and pushes back against the battery. Less voltage is left for the resistor, so the current shrinks.

The capacitor voltage follows V(t)=ε(1−e−t/RC). The current follows the opposite curve, I(t)=εRe−t/RC, starting high and decaying toward zero. Theoretically the capacitor never quite reaches ε, but after a few time constants the difference is too small to matter.

The graph shows both the charging and discharging curves for the same circuit. Notice how steep the curves are at the start and how flat they become later.

Example 2 Capacitor voltage partway through charging

An uncharged 220 μF capacitor (2.20 × 10⁻⁴ F) is connected through a 10 kΩ resistor (10,000 Ω) to a 9.0 V battery. What is the capacitor voltage 3.0 s after the switch closes?

  1. Given:
    • emf of the source (final voltage): ε=9 V
    • time since charging began: t=3 s
    • resistance: R=10,000 Ω
    • capacitance: C=2.2×10−4 F
  2. Formula: V(t)=ε(1−e−t/RC)
  3. Substitute: ε=9 V,t=3 s,R=10,000 Ω,C=2.2×10−4 F
  4. Answer: V=6.698 V

Here τ = 2.2 s, so 3.0 s is about 1.4 time constants, and the capacitor is roughly three quarters of the way to 9 V, past the 63% mark reached after one τ.

Graph of capacitor voltage over 11 seconds: a rising charging curve and a falling discharging curve, both with a 2.2 s time constant
With R = 10 kΩ and C = 220 μF the time constant is 2.2 s; both curves cover about 63% of their change in the first τ.

How Does a Capacitor Discharge Through a Resistor?

Disconnect the battery and connect a charged capacitor across a resistor. The capacitor now acts as the source. Its voltage pushes current through the resistor, the charge on its plates drops, and with less charge the voltage drops too, so the current slows.

The voltage follows V(t)=V0e−t/RC, where V₀ is the starting voltage. This is exponential decay, the same pattern seen in radioactive decay and a cooling cup of coffee. In every time constant the voltage falls to 36.8% of what it was at the start of that interval, no matter how big it was.

To find how long a discharge takes, rearrange the equation into t=RCln⁡(V0V). The voltage halves every 0.693τ, because ln 2 is about 0.693.

Example 3 How long until the voltage falls to a quarter?

A 470 μF capacitor (4.70 × 10⁻⁴ F) charged to 12 V discharges through a 2.0 kΩ resistor (2,000 Ω). How long does it take for its voltage to fall to 3.0 V?

  1. Given:
    • initial voltage: V0=12 V
    • capacitor voltage at time t: V=3 V
    • resistance: R=2,000 Ω
    • capacitance: C=4.7×10−4 F
  2. Formula: t=RCln(V0V)
  3. Substitute: V0=12 V,V=3 V,R=2,000 Ω,C=4.7×10−4 F
  4. Answer: t=1.303 s

Falling to one quarter takes two half-lives, which is ln 4, or about 1.39 time constants.

How Much Does a Capacitor Charge After Each Time Constant?

Because the curves are exponential, the fraction of the way to the end point depends only on how many time constants have passed, not on the actual values of R, C or the voltage. That makes the table below useful for every RC circuit you will meet.

A quick way to remember it: after 1τ about two thirds, after 2τ about seven eighths, after 3τ about 95%, and after 5τ essentially all. Discharging is the same table read from the other column.

Capacitor voltage after whole and fractional numbers of time constants
Time elapsedCharging: % of final voltageDischarging: % of starting voltage
0.5τ39.3%60.7%
0.693τ (one half-life)50.0%50.0%
1τ63.2%36.8%
2τ86.5%13.5%
3τ95.0%5.0%
4τ98.2%1.8%
5τ99.3%0.7%
Source: Computed with V/ε = 1 − e^(−t/τ) and V/V₀ = e^(−t/τ) · Retrieved October 2026

Where Does the Energy Go in an RC Circuit?

While charging, the battery delivers energy and the capacitor stores some of it in its electric field, U=12CV2. The rest is turned into heat in the resistor. A neat result of the math is that, charging from zero, exactly half of the energy from the battery ends up stored and half is lost as heat, whatever the value of R.

During discharge, all of the stored energy is converted into heat in the resistor, or into light and sound if the resistor is a lamp or a flash tube. For the stored energy itself, see energy stored in a capacitor.

What Are RC Circuits Used For?

  • Timers and blinkers. The charging time of an RC pair sets how long a light stays on, how often a turn signal flashes or how long a delay lasts before a device switches.
  • Camera flashes. A capacitor charges slowly from a small battery, then dumps its energy through the flash tube in a fraction of a millisecond.
  • Power supply smoothing. A large capacitor charges on each peak of rectified alternating current and discharges slowly between peaks, flattening the ripple.
  • Filters. Because a capacitor passes fast changes and blocks steady voltages, RC pairs can remove hiss from audio, block DC from a speaker or smooth noisy sensor readings.
  • Debouncing switches. An RC circuit hides the rapid flickering contacts of a mechanical button from a microcontroller.
  • Heart defibrillators and pacemakers. Both rely on capacitors charging and discharging through the body or timing resistors.
Compact camera flash firing a bright burst of light in a dim room, powered by a capacitor charged through a resistor
A camera flash charges a capacitor slowly through a resistor, then releases the energy in a split second.

How Are RC Circuits Related to Other Circuits?

Once the capacitor is fully charged, no steady current flows through it, so it behaves like an open switch in a DC circuit. Right after the switch closes on an empty capacitor, it behaves like a plain wire. Those two limits make quick checks easy: use Ohm's law with the capacitor treated as a wire at t = 0 and as a gap at the end.

Resistors and capacitors in combination follow the usual rules: work out the equivalent resistance and equivalent capacitance first, using resistors in series and parallel and capacitors in series and parallel, then multiply them for τ. The magnetic cousin of an RC circuit is the RL circuit, where an inductor slows changes in current with a time constant of L/R.

Practice RC Circuit Problems

Try the examples above with your own numbers, then check them with the capacitor calculator. For more circuit practice, the series and parallel circuits worksheets build the skills you need before tackling time-dependent circuits, and the capacitance page reviews Q = CV.

Common Misconceptions

Myth: A capacitor charges instantly when connected to a battery.

Physics: Any real circuit has resistance, so charging takes time. The time constant RC sets how long, from microseconds in fast circuits to minutes in large timing circuits.

Myth: After one time constant the capacitor is fully charged.

Physics: After one τ it is only about 63% charged. It takes about five time constants to get within 1% of the final voltage.

Myth: Current flows through the capacitor's insulator while it charges.

Physics: No charge crosses the gap. Electrons pile onto one plate and leave the other, so current flows in the wires on both sides while the insulator stays an insulator.

Myth: A larger battery voltage makes the capacitor charge faster.

Physics: A higher voltage raises the final voltage and the current, but the time constant RC and the percentage reached after each τ stay exactly the same.

Key Facts

  • An RC circuit contains a resistor and a capacitor, and the capacitor charges or discharges gradually.
  • The time constant is τ = RC, measured in seconds.
  • After one time constant a charging capacitor reaches about 63.2% of the supply voltage.
  • After one time constant a discharging capacitor falls to about 36.8% of its starting voltage.
  • A capacitor is considered fully charged or discharged after about five time constants.
  • The charging current starts at ε/R and decays toward zero.
  • RC circuits are used in timers, camera flashes, filters and power supply smoothing.
Did you know? When a capacitor charges from zero through a resistor, exactly half the energy taken from the battery is lost as heat, and this is true whether the resistor is one ohm or a million ohms; a bigger resistor just spreads the loss over a longer time.

Quick Quiz: How Well Do You Know RC Circuits?

6 questions. Tap an answer to check it.

  1. What is the time constant of a circuit with R = 2,000 Ω and C = 0.001 F?

  2. After one time constant, a charging capacitor has reached about what fraction of its final voltage?

  3. What happens to the time constant if the capacitance is doubled?

  4. When is the charging current in an RC circuit largest?

  5. About how many time constants does it take for a capacitor to be considered fully charged?

  6. A capacitor discharging through a resistor drops to what fraction of its starting voltage after one time constant?

Frequently Asked Questions

What is an RC circuit in simple words?

An RC circuit is a circuit with a resistor and a capacitor that work together to control timing. The resistor slows the flow of charge, so the capacitor fills up or empties gradually instead of all at once. How slowly depends on the product of resistance and capacitance, called the time constant. That smooth, predictable change is what makes RC circuits useful as timers and filters.

What is the time constant of an RC circuit?

The time constant is τ = RC, the resistance in ohms multiplied by the capacitance in farads, giving an answer in seconds. It is the time a charging capacitor takes to reach about 63.2% of its final voltage, or a discharging capacitor takes to drop to about 36.8% of its starting voltage. Bigger resistors or capacitors make the time constant longer.

Why is it 63% after one time constant?

The charging equation is V = ε(1 − e^(−t/RC)). At t = RC the exponent is −1, and e^(−1) is about 0.368. Subtracting that from 1 leaves about 0.632, so the capacitor has reached 63.2% of the supply voltage. The number comes purely from the exponential function, so it is the same for every RC circuit regardless of component values.

How long does it take to fully charge a capacitor?

Mathematically, never quite, because the exponential curve only approaches the final voltage. In practice, engineers say a capacitor is fully charged after about five time constants, when it is above 99% of the final voltage. For a 10 kΩ resistor with a 100 μF capacitor, τ is 1 second, so full charge takes about 5 seconds.

What is the discharging equation of a capacitor?

A capacitor discharging through a resistor follows V(t) = V₀ e^(−t/RC), where V₀ is its starting voltage. The charge and the current follow the same shape. To find the time to reach a certain voltage, rearrange it to t = RC ln(V₀/V). The voltage halves every 0.693 time constants, which works just like a half-life.

What happens to the current in an RC circuit while charging?

The current is largest the moment the switch closes, equal to the supply voltage divided by the resistance, because the empty capacitor offers no opposing voltage. As the capacitor charges, its voltage subtracts from the supply, so the voltage across the resistor and the current both decay exponentially with the same time constant, approaching zero when the capacitor is full.

What is an RC circuit used for?

RC circuits set time delays, make lights blink, smooth the output of power supplies, filter unwanted frequencies out of audio and sensor signals, and clean up noisy button presses for microcontrollers. Camera flashes charge a capacitor through a resistor and then release its energy quickly. Many oscillators and clock circuits also use RC charging to set their frequency.

Does a capacitor block DC current?

Once it is fully charged, yes. In a steady DC circuit no current flows through a charged capacitor, so it acts like a break in the wire. Current does flow briefly while the capacitor charges or discharges, which is what an RC circuit is all about. With alternating current the capacitor keeps charging and discharging, so AC signals pass through.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.