Controlled fission

How a Nuclear Reactor Works

A nuclear reactor is a machine that runs a controlled, self-sustaining fission chain reaction and turns the released energy into heat. In a power plant, that heat boils water into steam, the steam spins a turbine, and the turbine drives a generator that makes electricity. Control rods, a moderator and a coolant keep the reaction steady, exactly balanced between growing and dying out.

Nuclear power station by a river at sunrise, with steam rising from cooling towers beside the domed reactor containment building
The dome holds the reactor; the towers release waste heat as harmless water vapor.

At a Glance

A nuclear reactor splits uranium-235 nuclei in a controlled chain reaction, with each fission releasing about 200 MeV, mostly as heat in the fuel. A coolant carries the heat to a steam generator, and the steam drives a turbine and generator. Like any heat engine, its efficiency is e = W / Q_h, typically about one third.

What it does
Sustains a controlled fission chain reaction to produce heat
Energy chain
Nuclear energy → heat → steam → turbine motion → electricity
Formula
Efficiency e = W / Qh; energy from mass E = mc²
Main parts
Fuel rods, moderator, control rods, coolant, pressure vessel, containment
Typical large plant
About 3,000 MW of heat for about 1,000 MW of electricity
First reactor
Chicago Pile-1, 2 December 1942
On this page
  1. What Is a Nuclear Reactor?
  2. How Does a Nuclear Reactor Work Step by Step?
  3. What Are the Main Parts of a Nuclear Reactor?
  4. How Does Fission Turn Into Heat?
  5. Why Is a Nuclear Power Plant Only About One-Third Efficient?
  6. How Is the Chain Reaction Controlled?
  7. What Are the Different Types of Nuclear Reactors?
  8. How Safe Are Nuclear Reactors?
  9. Who Built the First Nuclear Reactor?
  10. Common Misconceptions
  11. Key Facts
  12. Quiz
  13. FAQ

What Is a Nuclear Reactor?

A nuclear reactor is a carefully engineered container in which uranium or plutonium nuclei split at a steady, controlled rate. Every fission releases a burst of energy and a few neutrons, and the reactor is arranged so that, on average, exactly one of those neutrons goes on to cause the next fission. The result is a chain reaction that neither grows nor fades.

Most reactors exist to make heat. In a power station, that heat is used exactly as the heat from burning coal would be: to make steam, spin a turbine and drive an electric generator. Smaller research reactors are used mainly as sources of neutrons, and naval reactors drive ships and submarines.

A reactor cannot explode like a nuclear weapon. Its fuel is only slightly enriched in uranium-235 and is spread out among moderator and coolant, so a fast, runaway chain reaction of the kind a bomb needs is physically impossible.

How Does a Nuclear Reactor Work Step by Step?

Here is the path energy takes through a typical pressurized water reactor, the most common design in the world:

  1. Fission in the fuel. Uranium-235 nuclei in the fuel pellets absorb slow neutrons and split, releasing heat and fresh fast neutrons.
  2. Slowing the neutrons. The fast neutrons bounce off the hydrogen nuclei in the surrounding water, the moderator, until they are slow enough to be captured by uranium-235.
  3. Controlling the rate. Control rods made of neutron-absorbing materials are raised or lowered to keep the chain reaction exactly critical.
  4. Carrying away heat. Water pumped through the core at high pressure heats to around 300 °C without boiling and carries the heat out of the reactor vessel.
  5. Making steam. In the steam generator, this hot water passes through thousands of tubes and boils water in a separate loop.
  6. Spinning the turbine. The steam expands through a turbine, which turns a generator and produces electricity.
  7. Cooling and recycling. The steam is condensed back to water using a river, the sea or a cooling tower, then pumped back to the steam generator.

The radioactive water in the core never touches the turbine. It stays in its own sealed loop inside the containment building.

What Are the Main Parts of a Nuclear Reactor?

Every power reactor, whatever its design, has the same basic set of parts. The table summarizes what each one does. The fuel provides the fissile nuclei, the moderator slows neutrons, the control rods absorb spare neutrons, and the coolant removes heat. Around them sit the steel reactor vessel, the biological shield of concrete, and the containment building, a thick reinforced structure designed to hold in radioactive material even after a serious accident.

Fuel comes as ceramic pellets of uranium dioxide stacked inside thin metal tubes called fuel rods. Hundreds of rods are bundled into fuel assemblies, and a large core holds a couple of hundred assemblies, adding up to many tonnes of uranium.

Main parts of a nuclear reactor and what each one does
PartTypical materialJob
Fuel rodsUranium dioxide pellets in metal tubesHold the fissile nuclei where fission happens
ModeratorOrdinary water, heavy water or graphiteSlows fast neutrons so uranium-235 can capture them
Control rodsBoron, cadmium or hafnium compoundsAbsorb neutrons to keep k at exactly 1 or shut the reactor down
CoolantWater, heavy water, carbon dioxide, helium, liquid sodiumCarries heat out of the core
Reactor vesselThick steelHolds the core and coolant under pressure
Steam generatorBundles of metal tubesTransfers heat from the core loop to make steam
Containment buildingSteel-lined reinforced concreteKeeps radioactive material inside during an accident
Source: General description of power reactor designs; materials vary by reactor type · Retrieved October 2026
Close-up of a nuclear fuel assembly, a square bundle of thin metal fuel rods held in place by grid spacers
Fuel rods are bundled into assemblies, and a power reactor's core holds a couple of hundred of them.

How Does Fission Turn Into Heat?

Most of the energy from each fission, about 168 MeV out of roughly 200, appears as the speed of the two fragments. These fragments are heavy and highly charged, so they plow through the fuel only a few thousandths of a millimeter before stopping. Along the way they knock into countless atoms and make them vibrate faster, which is exactly what heat is. The bar chart follows that energy from motion of the fragments into thermal energy of the fuel.

The remaining energy arrives as neutrons, gamma rays and the later radioactive decay of the fragments. Even after a reactor shuts down, this decay keeps producing heat, a few percent of full power at first. That decay heat is why cooling must never stop, even in a reactor that is switched off.

Since all this energy comes from mass, the fuel actually becomes lighter as the reactor runs, as the example below shows using E = mc².

Example 3 Mass converted in one day

The same core produces 3.4 × 10^9 J of heat every second for a full day of 86,400 s, a total of 2.9376 × 10^14 J. How much mass is converted into energy in that day?

  1. Given:
    • rest energy: E=2.938×1014 J
    • speed of light in vacuum: c=299,792,458 m/s
  2. Formula: m=Ec2
  3. Substitute: E=2.938×1014 J,c=299,792,458 m/s
  4. Answer: m=0.003269 kg

Only a few grams of mass vanish per day, even though tonnes of uranium sit in the core.

Energy bar chart: about 168 MeV of fission fragment kinetic energy turns into thermal energy as the fragments stop inside the fuel
The fragments of one fission carry about 168 MeV of motion, which becomes heat within a tiny distance inside the fuel pellet.

Why Is a Nuclear Power Plant Only About One-Third Efficient?

Once fission has made heat, the rest of the plant obeys the same rules as any heat engine. Heat flows from a hot source, the reactor, to a cold sink, the cooling water, and a turbine captures part of that flow as work. The second law of thermodynamics says that some heat must always be rejected to the cold side.

How much work you can extract depends on how hot the steam is. Water-cooled reactors keep their coolant at around 300 °C so it stays liquid under pressure, which limits the steam temperature and holds efficiency near one third. Reactors cooled by gas or molten salt can run hotter and reach higher efficiencies. The examples below work through a typical large plant.

A nuclear power plant is a heat engine: the reactor is the hot source, and only part of its heat can become electrical work. This formula gives the fraction that does.

e=WQh=1−QcQh
What each symbol means
SymbolQuantitySI unit
ethermal efficiencydimensionless (1)
Wnet work output per cyclejoule (J)
Qhheat absorbed from the hot reservoirjoule (J)
Qcheat rejected to the cold reservoirjoule (J)

Rearranged to find another variable:

W=eQhQh=WeQc=Qh−W

Valid for: cyclic engine; W = Q_h − Q_c (magnitudes).

Example 1 Efficiency of a large power reactor

Each second, a reactor core delivers 3.4 × 10^9 J of heat to its steam system, and the plant sends 1.15 × 10^9 J of electrical energy to the grid. What is the plant's thermal efficiency?

  1. Given:
    • net work output per cycle: W=1.15×109 J
    • heat absorbed from the hot reservoir: Qh=3.4×109 J
  2. Formula: e=WQh=1−QcQh
  3. Substitute: W=1.15×109 J,Qh=3.4×109 J
  4. Answer: e=0.3382

Multiply by 100 for a percentage. About a third is normal for water-cooled reactors, because their steam is cooler than the steam in modern coal or gas plants.

Example 2 Where does the rest of the heat go?

Using the same plant, with 3.4 × 10^9 J of heat in and 1.15 × 10^9 J of electrical work out each second, how much heat must be released to the cooling water or cooling towers every second?

  1. Given:
    • heat absorbed from the hot reservoir: Qh=3.4×109 J
    • net work output per cycle: W=1.15×109 J
  2. Formula: Qc=Qh−W
  3. Substitute: Qh=3.4×109 J,W=1.15×109 J
  4. Answer: Qc=2.25×109 J (2,250 MJ)

This waste heat is why reactors sit beside rivers, lakes or seas, or use tall cooling towers.

How Is the Chain Reaction Controlled?

The key number is the multiplication factor k, the average number of new fissions caused by the neutrons from one fission. At exactly 1 the reactor is critical and its power stays constant. Operators adjust k with control rods, and in many designs with boron dissolved in the coolant, both of which soak up neutrons.

Control is possible because a small share of neutrons, well under one percent for uranium-235, are not released at the instant of fission. They come out seconds later from the decay of certain fragments. These delayed neutrons slow the response of the whole reactor, so power changes over tens of seconds instead of thousandths of a second, giving the control system plenty of time to act.

Well-designed reactors also have built-in feedback. If the water gets hotter it becomes less dense and slows neutrons less well, so fewer fissions happen and the power drops by itself. In an emergency, all control rods drop into the core in a couple of seconds, a shutdown known as a scram. The graph shows how power changes with time when the reactor is slightly supercritical, exactly critical, and just after a shutdown.

Graph of reactor power over 120 s starting at 100%: rising slowly when supercritical, flat when critical, falling after shutdown
Thanks to delayed neutrons, reactor power changes over tens of seconds, slow enough for control rods to keep up.

What Are the Different Types of Nuclear Reactors?

Reactors are grouped mainly by their coolant and moderator. Pressurized water reactors keep the core water under high pressure and use a separate loop for steam; they make up the majority of the world's fleet. Boiling water reactors let the water boil inside the core and send that steam straight to the turbine. Heavy water reactors use water made with deuterium as moderator, which absorbs so few neutrons that natural, unenriched uranium can be used.

Gas-cooled reactors use carbon dioxide or helium as coolant and graphite as moderator. Fast reactors have no moderator at all; they use fast neutrons and can breed new plutonium fuel from uranium-238. Newer small modular reactors aim to build smaller units in factories and ship them to the site.

Common reactor types compared
TypeCoolantModeratorFuel
Pressurized water reactor (PWR)Water under high pressureWaterEnriched uranium, a few percent U-235
Boiling water reactor (BWR)Boiling waterWaterEnriched uranium
Pressurized heavy water reactorHeavy waterHeavy waterNatural uranium
Advanced gas-cooled reactorCarbon dioxideGraphiteEnriched uranium
Fast breeder reactorLiquid sodiumNonePlutonium and uranium mix
High-temperature gas reactorHeliumGraphiteCoated fuel particles
Source: Qualitative summary of standard reactor classifications · Retrieved October 2026

How Safe Are Nuclear Reactors?

Reactor safety relies on several independent barriers, an approach called defense in depth: ceramic fuel, sealed fuel rods, a thick steel pressure vessel and a reinforced containment building. Backup pumps, power supplies and emergency cooling systems are designed to remove decay heat even if normal systems fail.

The two worst accidents show what happens when these layers fail. At Chernobyl in 1986, an unstable reactor design and an unsafe test led to a power surge, a steam explosion and a fire with no containment building to stop the release. At Fukushima in 2011, a tsunami cut off power to the cooling pumps, and decay heat melted fuel in three reactors. Spent fuel, which contains long-lived radioactive fission products, is cooled in water pools for years and then stored in sealed casks.

Who Built the First Nuclear Reactor?

The first human-made reactor was Chicago Pile-1, built under the stands of a sports field at the University of Chicago. A team led by Enrico Fermi, including Leo Szilard and Leona Woods, stacked about 45,000 graphite blocks around uranium metal and uranium oxide. On 2 December 1942, they slowly withdrew a control rod and recorded the first self-sustaining chain reaction.

The pile had no cooling and no shielding and ran at less than a watt. Within a decade, reactors were generating electricity, and by the late 1950s the first commercial nuclear power stations were feeding national grids. Today hundreds of reactors supply roughly a tenth of the world's electricity. The broader story of these power sources is on our nuclear energy page.

Common Misconceptions

Myth: Nuclear reactors make electricity directly from radiation.

Physics: Reactors make heat. The electricity comes from a conventional steam turbine and generator, the same as in a fossil-fuel plant.

Myth: The clouds rising from cooling towers are radioactive smoke.

Physics: Those clouds are plain water vapor from the cooling system, which never touches the reactor core.

Myth: Pulling out the control rods makes the reactor explode.

Physics: Withdrawing rods raises power gradually, slowed by delayed neutrons and countered by temperature feedback and automatic shutdown systems.

Key Facts

  • A nuclear reactor runs a controlled fission chain reaction with a multiplication factor of exactly 1.
  • The heat from fission makes steam that spins a turbine and generator, just as in a coal or gas plant.
  • The moderator slows neutrons, control rods absorb them, and the coolant carries heat away.
  • Delayed neutrons, released seconds after fission, make reactor power change slowly enough to control.
  • A typical large plant turns about one third of its heat into electricity and rejects the rest to cooling water.
  • A reactor cannot explode like a nuclear bomb, because its fuel is far too dilute for a runaway fast chain reaction.
  • The first reactor, Chicago Pile-1, went critical on 2 December 1942.
Did you know? A large reactor converts only a few grams of mass into energy each day, but to make the same heat a coal plant would need to burn about 12,000 tonnes of coal (computed with a typical 24 MJ per kilogram).

Quick Quiz: How Well Do You Know How a Nuclear Reactor Works?

6 questions. Tap an answer to check it.

  1. What is the main product of a nuclear reactor in a power station?

  2. What does the moderator do?

  3. To lower a reactor's power, operators should...

  4. Why can operators control a reactor's power smoothly?

  5. A plant uses 3,000 MW of heat to make 1,000 MW of electricity. What is its efficiency?

  6. Where did the first self-sustaining nuclear chain reaction take place?

Frequently Asked Questions

How does a nuclear reactor produce electricity?

The reactor splits uranium nuclei in a controlled chain reaction, which heats the fuel. A coolant, usually water, carries that heat to a steam generator or boils directly into steam. The steam spins a turbine connected to a generator, which produces electricity. The steam is then condensed with cooling water and pumped back to be heated again.

What fuel does a nuclear reactor use?

Most reactors use uranium dioxide fuel enriched so that a few percent of the uranium is uranium-235, the isotope that splits easily with slow neutrons. Some designs use natural uranium with heavy water as moderator, and others use mixed uranium and plutonium oxide. A fuel assembly typically stays in the core for several years before it is replaced.

What do control rods do in a nuclear reactor?

Control rods contain materials such as boron, cadmium or hafnium that absorb neutrons strongly. Inserting them deeper removes more neutrons, lowering the multiplication factor and the power. Pulling them out does the opposite. In an emergency, all rods drop fully into the core within seconds and stop the chain reaction.

What is the purpose of a moderator?

Fission releases fast neutrons, but uranium-235 captures slow neutrons far more readily. The moderator, usually water, heavy water or graphite, slows the neutrons through repeated collisions with light nuclei without absorbing too many of them. Slower neutrons make a chain reaction possible in fuel with only a few percent uranium-235.

Can a nuclear reactor explode like an atomic bomb?

No. A bomb needs highly enriched fissile material assembled into a supercritical mass in a tiny fraction of a second. Reactor fuel is only slightly enriched and is spread out among coolant and moderator, so a runaway fast chain reaction cannot occur. Reactors can suffer steam or hydrogen explosions if cooling fails, but not a nuclear blast.

How long does nuclear fuel last in a reactor?

A fuel assembly in a typical water-cooled power reactor stays in the core for about four to six years, with roughly a third of the core replaced every year or two during a refueling outage. Afterward, the spent fuel is still hot and radioactive, so it is stored in a cooling pool for several years before moving to dry casks.

Why do nuclear plants need so much cooling water?

Like every steam power plant, a nuclear plant can turn only part of its heat into electricity. Roughly two thirds of the heat must be released to the surroundings to condense the steam back into water. That is why plants are built next to rivers, lakes or the sea, or use large cooling towers that release the heat as water vapor.

What happens when a nuclear reactor shuts down?

When the control rods drop in, the chain reaction stops within seconds, and the power falls quickly to a few percent of its full value. That remaining heat comes from the radioactive decay of fission products and fades slowly over days and weeks. Cooling systems must keep running to remove it, or the fuel could overheat.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.