
At a Glance
Newton's second law for rotation says the net torque on a rigid body equals its moment of inertia times its angular acceleration: τ_net = I α. Torque is in newton meters, moment of inertia in kilogram square meters and angular acceleration in radians per second squared.
- Based on
- Newton's second law of motion (1687), extended to rigid bodies in the 1700s
- Formula
- τnet = Iα
- SI units
- τ in N·m, I in kg·m², α in rad/s²
- Scalar or vector
- Vector law: α points along the net torque (about a fixed axis, signs are enough)
- Applies to
- Rigid bodies turning about a fixed axis or about their center of mass
On this page
- What Does Newton's Second Law for Rotation Say?
- Newton's Second Law for Rotation Explained Simply
- What Is the Formula for Newton's Second Law for Rotation?
- How Does τ = Iα Mirror F = ma?
- Why Does the Law Use Net Torque?
- How Does an Object's Shape Change Its Angular Acceleration?
- How Do You Solve a Falling Mass and Pulley Problem?
- Where Do You See Newton's Second Law for Rotation in Everyday Life?
- Who Came Up With the Rotational Form of Newton's Second Law?
- Going Deeper: When Does τ = Iα Need Extra Care?
- Practice Newton's Second Law for Rotation
- Common Misconceptions
- Key Facts
- Quiz
- FAQ
What Does Newton's Second Law for Rotation Say?
The law links three quantities. Net torque is the total twisting effect of all the forces on an object. Moment of inertia measures how hard the object is to spin up or slow down, and angular acceleration is how fast its spin rate changes. The law says
Read it from right to left and it becomes a prediction. Give a wheel more net torque and its angular acceleration grows in proportion. Give it a larger moment of inertia and the same torque produces a smaller change in spin.
The law is not a new principle of nature. It follows from Newton's second law, F = ma, applied to every small piece of a rigid object and then added up around the axis. That is why the two laws look so alike and why physicists often call this one the rotational form of F = ma.
Newton's Second Law for Rotation Explained Simply
Think about opening a heavy door. Push near the hinges and it barely moves. Push at the handle, far from the hinges, and it swings open easily. Your push is the same, but the twist, the torque, is much larger at the handle.
Now picture two doors, one light and hollow, one solid and heavy. With the same push at the handle, the light door swings faster. The heavy door has a bigger moment of inertia, so it gains spin more slowly.
That is the whole law in everyday terms. A bigger twist gives a faster change in spin, and a harder-to-turn object gives a slower change in spin.
What Is the Formula for Newton's Second Law for Rotation?
The law is written
The radian is the reason the units work out. One radian is a ratio of two lengths, so it carries no dimension, and
Every quantity must be measured about the same axis. A rod has one moment of inertia about its center and a larger one about its end, and the torques must be taken about that same line.
Here is the rotational second law with each symbol and its SI unit, plus the rearranged forms for finding the moment of inertia or the angular acceleration.
| Symbol | Quantity | SI unit |
|---|---|---|
| net torque | newton meter (N·m) | |
| moment of inertia | kilogram meter squared (kg·m²) | |
| angular acceleration | radian per second squared (rad/s²) |
Rearranged to find another variable:
Valid for: rigid body rotating about a fixed axis.
Example 1 Spinning up a potter's wheel
A potter kicks a heavy wheel that has a moment of inertia of 1.5 kg·m² about its shaft. After friction is accounted for, the net torque on the wheel is 6.0 N·m. What is the wheel's angular acceleration?
- Given:
- net torque:
- moment of inertia:
- net torque:
- Formula:
- Substitute:
- Answer:
Every second of steady kicking adds this much angular velocity, measured in radians per second.
How Does τ = Iα Mirror F = ma?
Each quantity in straight-line motion has a rotational partner. Force becomes torque, mass becomes moment of inertia, and acceleration becomes angular acceleration. The equations have the same shape, so the same problem-solving habits carry over.
The partners are not identical, though. Mass belongs to the object alone, while moment of inertia also depends on where the axis is and how the mass is spread around it. A force depends only on how hard you push, while a torque also depends on where and at what angle you push.
The table below lists the main pairs. Many students find rotation much easier once they see that almost every rotational formula has a familiar twin from linear motion.
| Linear quantity | Symbol and unit | Rotational partner | Symbol and unit |
|---|---|---|---|
| Displacement | x (m) | Angular displacement | θ (rad) |
| Velocity | v (m/s) | Angular velocity | ω (rad/s) |
| Acceleration | a (m/s²) | Angular acceleration | α (rad/s²) |
| Mass | m (kg) | Moment of inertia | I (kg·m²) |
| Force | F (N) | Torque | τ (N·m) |
| Second law | F = ma | Second law for rotation | τ = Iα |
| Momentum | p = mv (kg·m/s) | Angular momentum | L = Iω (kg·m²/s) |
| Kinetic energy | ½mv² (J) | Rotational kinetic energy | ½Iω² (J) |
| Source: Standard definitions; SI units from BIPM · Retrieved October 2026 | |||
Why Does the Law Use Net Torque?
Most spinning objects feel several torques at once. A bicycle wheel has the chain pulling one way and friction in the hub pulling the other. Only the difference between them changes the spin, so the law uses the net torque, with torques that turn the object counterclockwise counted positive and clockwise ones negative (or the other way around, as long as you stay consistent).
When the net torque is zero, the angular acceleration is zero. The object either stays at rest or keeps spinning at a steady rate, which is the rotational version of the first law. Engineers use this case, called static equilibrium when nothing moves, to design beams, shelves and cranes.
A desk fan shows how a changing net torque plays out. The motor supplies a nearly constant torque, but air drag on the blades grows as they speed up. The net torque shrinks, the angular acceleration shrinks with it, and the blade settles at a steady speed when drag torque equals motor torque.
Example 2 How hard to push a merry-go-round
A loaded playground merry-go-round has a moment of inertia of 500 kg·m². A parent wants it to gain angular velocity at a rate of 0.40 rad/s². Ignoring bearing friction, what net torque is needed?
- Given:
- moment of inertia:
- angular acceleration:
- moment of inertia:
- Formula:
- Substitute:
- Answer:
Pushing at the rim, 2 m from the center, would need a force of about a hundred newtons; pushing near the axle would need far more.

How Does an Object's Shape Change Its Angular Acceleration?
Two objects with the same mass can respond very differently to the same torque. What matters is how far the mass sits from the axis, because moment of inertia grows with the square of that distance. A thin ring with all its mass at the rim is twice as hard to spin up as a solid disk of the same mass and radius.
The table compares six objects that all have a mass of 2 kg and the same overall size, each given the same 2 N·m net torque. The rod spun about its end responds four times more slowly than the same rod spun about its middle, a difference explained by the parallel axis theorem.
Designers use this in both directions. Racing bicycle wheels keep their rims light so riders can accelerate quickly, while flywheels put heavy mass at the rim so they resist sudden changes in speed.
| Object (mass 2 kg) | Moment of inertia (kg·m²) | Angular acceleration (rad/s²) |
|---|---|---|
| Thin hoop, radius 0.30 m, about its center | 0.18 | 11.11 |
| Hollow sphere, radius 0.30 m, about a diameter | 0.12 | 16.67 |
| Solid disk, radius 0.30 m, about its axle | 0.09 | 22.22 |
| Solid sphere, radius 0.30 m, about a diameter | 0.072 | 27.78 |
| Thin rod, length 0.60 m, about its center | 0.06 | 33.33 |
| Thin rod, length 0.60 m, about one end | 0.24 | 8.333 |
| Source: Computed with α = τ/I and the standard moment of inertia formulas for each shape · Retrieved October 2026 | ||
How Do You Solve a Falling Mass and Pulley Problem?
A block hanging from a cord wrapped around a pulley is the classic test of this law, because it combines straight-line and rotational motion. The method has four steps.
- Draw a free-body diagram of the block and write
for it. - Write the rotational law for the pulley: the cord tension acts at the rim, so
. - Link the two motions. If the cord does not slip, the block's acceleration equals the rim's tangential acceleration,
. - Solve the three equations together for the unknown you want.
The result shows something useful. The tension in the cord is always less than the block's weight, because the block is accelerating downward, and the pulley's mass slows the whole system compared with a massless pulley.
Example 3 A weight falling from a spool
A cord is wrapped around a solid disk pulley of mass 4.0 kg and radius 0.10 m that turns on a frictionless axle. A 2.0 kg block hangs from the free end of the cord and is released. Take g = 9.81 m/s². What is the angular acceleration of the pulley?
- Given:
- m:
- M:
- R:
- g:
- m:
- Formula:
- Substitute:
- Answer:
This comes from combining F = ma for the block with τ = Iα for the disk, using I = ½MR² and a = αR, as the section above shows.

Where Do You See Newton's Second Law for Rotation in Everyday Life?
- Revolving doors: pushing at the outer edge gives the largest torque, so the heavy door starts turning with little effort.
- Car engines and wheels: the engine's torque, multiplied by the gears, sets how quickly the wheels gain spin.
- Figure skaters and divers: they change their moment of inertia by pulling in their arms, though that is mostly a story about angular momentum once they are spinning freely.
- Washing machines: a large motor torque brings the drum up to spin speed within a minute or so despite the wet clothes inside.
- Wrenches and screwdrivers: a longer handle gives a larger torque from the same hand force, so stuck bolts start to turn.
- Hard drives and fans: small motors give a modest torque, so the spinning parts take a moment to reach full speed.
In each case, the speed of the spin-up comes from comparing the net torque with the moment of inertia, exactly as the law predicts.

Who Came Up With the Rotational Form of Newton's Second Law?
Isaac Newton published his laws of motion in 1687, but he stated them for bodies treated as points. He did not write a separate law for spinning solid objects.
The rotational form grew out of work in the 1700s by mathematicians who extended Newton's ideas to rigid bodies. Leonhard Euler played a central part, introducing ideas close to what we now call moment of inertia and writing general equations for the rotation of solid bodies in the 1750s and 1760s. The simple form
Because the law follows directly from F = ma, it keeps Newton's name. The idea that a twist depends on distance from a pivot is much older, going back to the lever studies of Archimedes.
Going Deeper: When Does τ = Iα Need Extra Care?
The simple form assumes a rigid body with a constant moment of inertia, turning about a fixed axis or about an axis through its center of mass. If the object changes shape while spinning, like a skater pulling in her arms,
For an object tumbling freely in three dimensions, angular momentum and angular velocity need not point the same way. A spinning top or a thrown book can wobble in ways that
Torques must also be measured about a sensible point. Taking them about a fixed pivot or about the center of mass always works, while taking them about an arbitrary accelerating point can give wrong answers.
Practice Newton's Second Law for Rotation
To check your own numbers, use our rotational motion calculator or the torque calculator. Printable problem sets with answer keys are in our torque worksheets, and every rotational equation is collected on the rotational motion formulas page.
Common Misconceptions
Myth: Moment of inertia is just another name for mass.
Physics: Mass is one number for an object, but moment of inertia depends on the axis and on how far the mass sits from it. The same object has different moments of inertia about different axes.
Myth: A bigger force always produces a bigger angular acceleration.
Physics: What matters is torque, which depends on the force, its distance from the axis and its angle. A large force aimed straight at the axis produces no torque at all.
Myth: If something is spinning, there must be a net torque on it.
Physics: A net torque is needed only to change the spin. With zero net torque an object keeps rotating at a constant angular velocity.
Myth: Angular acceleration can be measured in revolutions per minute.
Physics: Revolutions per minute is a unit of angular velocity. Angular acceleration is a rate of change of angular velocity, so in SI units it is rad/s².
Key Facts
- Newton's second law for rotation states that net torque equals moment of inertia times angular acceleration, τ = Iα.
- Torque is measured in N·m, moment of inertia in kg·m² and angular acceleration in rad/s².
- Angular acceleration always points along the net torque, so a zero net torque means a constant spin rate.
- The same torque gives a smaller angular acceleration when mass sits farther from the axis.
- Torque and moment of inertia must both be measured about the same axis.
- The law follows from F = ma applied to every part of a rigid body.
- When the moment of inertia changes, the more general form τ = ΔL/Δt applies.
Quick Quiz: How Well Do You Know Newton's Second Law for Rotation?
6 questions. Tap an answer to check it.
A net torque of 12 N·m acts on a wheel with a moment of inertia of 3 kg·m². What is its angular acceleration?
α = τ_net / I = 12 N·m / 3 kg·m² = 4 rad/s².
Which quantity plays the role of mass in Newton's second law for rotation?
Moment of inertia measures resistance to changes in rotation, just as mass measures resistance to changes in linear motion.
A wheel spins at a steady 30 rad/s. What is the net torque on it?
A steady spin means zero angular acceleration, so the net torque must be zero.
A hoop and a solid disk have the same mass and radius. The same torque acts on each. Which gains spin faster?
The disk has half the moment of inertia of the hoop, so the same torque gives it twice the angular acceleration.
A torque of 4 N·m gives a flywheel an angular acceleration of 8 rad/s². What is its moment of inertia?
I = τ_net / α = 4 N·m / 8 rad/s² = 0.5 kg·m².
In a falling block and pulley problem, how does the cord tension compare with the block's weight?
The block accelerates downward, so its weight must exceed the upward tension.
Frequently Asked Questions
What is Newton's second law for rotation?
It is the rotational form of F = ma. It says the net torque on a rigid object equals its moment of inertia times its angular acceleration, τ = Iα. A larger net torque produces a faster change in spin, while a larger moment of inertia produces a slower one for the same torque.
What is the formula for Newton's second law in rotational motion?
The formula is τ_net = I α. Net torque τ is in newton meters, moment of inertia I is in kilogram square meters and angular acceleration α is in radians per second squared. You can rearrange it as α = τ/I to find angular acceleration or as I = τ/α to find moment of inertia.
How is τ = Iα similar to F = ma?
Each term has a direct partner. Torque plays the role of force, moment of inertia plays the role of mass, and angular acceleration plays the role of acceleration. The two laws have the same form because the rotational one is derived by applying F = ma to every small piece of a spinning object and adding up the results.
How do you find angular acceleration from torque?
Add up all the torques about the axis, keeping track of their directions, to get the net torque. Then find the moment of inertia of the object about that same axis. Divide the net torque by the moment of inertia, α = τ_net / I, and the answer comes out in radians per second squared when SI units are used.
Why does the rotational second law use net torque?
Only the combined effect of all the torques changes an object's spin. A wheel with a motor torque of 10 N·m and a friction torque of 4 N·m behaves as if a single 6 N·m torque were acting. Using just one torque would overestimate or underestimate the angular acceleration.
Does Newton's second law for rotation work if the moment of inertia changes?
The simple form τ = Iα assumes a constant moment of inertia. When an object changes shape while spinning, such as a diver tucking in, you need the general form: net torque equals the rate of change of angular momentum. With no outside torque, angular momentum stays constant even though the spin rate changes.
What units are used in τ = Iα?
In SI units, torque is in newton meters (N·m), moment of inertia is in kilogram square meters (kg·m²) and angular acceleration is in radians per second squared (rad/s²). Because the radian has no dimension, kg·m² times rad/s² reduces to kg·m²/s², which is the same as N·m.
Is Newton's second law for rotation a vector equation?
Yes. Torque and angular acceleration are vectors that point along the axis of rotation, using the right-hand rule. For problems with a fixed axis, you can treat them as signed numbers, with counterclockwise positive and clockwise negative, which is how most introductory problems are solved.
Who discovered Newton's second law for rotation?
Isaac Newton published the original second law in 1687 for point-like bodies. The rotational version for rigid bodies was developed in the 1700s by mathematicians extending his work, with Leonhard Euler making major contributions to the mechanics of rotating solids. The law still carries Newton's name because it follows directly from F = ma.
Sources
Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.








