Moving the axis of rotation

Parallel Axis Theorem

The parallel axis theorem states that the moment of inertia about any axis equals the moment of inertia about a parallel axis through the center of mass plus the total mass times the square of the distance between the two axes. In symbols, I = I_cm + Md². It lets you reuse one known value for countless pivot points.

Gymnast swinging fully stretched around a horizontal bar, rotating about an axis far from the body's center of mass
A gymnast swinging around a bar rotates about an axis far from the body's center of mass, so the Md² term dominates.

At a Glance

The parallel axis theorem says I = I_cm + M d^2: the moment of inertia about any axis equals the value about a parallel axis through the center of mass plus mass times distance squared. It shows that a body is easiest to spin about its center of mass, and every shift of the axis adds M d^2.

Also called
Huygens–Steiner theorem, Steiner's theorem
Named after
Christiaan Huygens (1600s) and Jakob Steiner (1800s)
Formula
I = Icm + Md²
SI unit
kilogram meter squared (kg·m²)
Applies to
Any rigid body, for two parallel axes, one through the center of mass
Key result
The moment of inertia is smallest about an axis through the center of mass
On this page
  1. What Does the Parallel Axis Theorem Say?
  2. The Parallel Axis Theorem Explained Simply
  3. What Is the Formula for the Parallel Axis Theorem?
  4. Why Does the Parallel Axis Theorem Work?
  5. How Does the Theorem Change the Moments of Inertia of Common Shapes?
  6. Where Is the Parallel Axis Theorem Used?
  7. How Does the Pivot Point Change the Swing of a Rod?
  8. Who Discovered the Parallel Axis Theorem?
  9. Going Deeper: When Can You Not Use the Parallel Axis Theorem?
  10. How Can You Practice Parallel Axis Theorem Problems?
  11. Common Misconceptions
  12. Key Facts
  13. Quiz
  14. FAQ

What Does the Parallel Axis Theorem Say?

The parallel axis theorem says that if you know how hard an object is to spin about an axis through its center of mass, you can find how hard it is to spin about any parallel axis. Just add the object's mass times the square of the distance between the axes.

The quantity being moved is the moment of inertia, the rotational version of mass. Tables list it for common shapes about their centers. Real objects, though, often turn about a hinge, a pin or a hand at one end. The theorem bridges that gap without any new integration.

Two conditions matter. The axes must be parallel, and one of them must pass through the center of mass. The second condition is the one students most often forget.

The Parallel Axis Theorem Explained Simply

Spin a broom by holding it in the middle and it twirls easily. Now hold it by the end and swing it around. It feels much heavier and slower to start, even though it has the same mass. The mass is now, on average, farther from your hand.

The theorem splits that extra effort into two parts. One part is the object spinning about its own center, which never changes. The other part is the whole mass being carried around a circle, as if it were a single lump sitting at the center of mass. Add the two parts and you have the total.

Since the second part can only add, the easiest axis to spin any object about is the one through its center of mass.

What Is the Formula for the Parallel Axis Theorem?

The theorem is written I=Icm+Md2. Here Icm is the moment of inertia about an axis through the center of mass, M is the total mass, d is the perpendicular distance between the two parallel axes and I is the moment of inertia about the new axis. All values are in SI units, so moments of inertia come out in kg·m².

The distance is squared, so it matters a lot. Moving the axis twice as far from the center of mass makes the added term four times larger. That is the same squared-distance pattern you see in the point-mass formula I=mr2.

You can also run the theorem backward. If you measure I about a convenient pivot, subtract Md2 to find Icm. Engineers do exactly that when they test sports equipment and machine parts by swinging them.

Here is the theorem with each variable and its SI unit, plus the forms solved for the center-of-mass value, the distance and the mass.

I=Icm+Md2
What each symbol means
SymbolQuantitySI unit
Imoment of inertia about the new axiskilogram meter squared (kg·m²)
Icmmoment of inertia about a parallel axis through the center of masskilogram meter squared (kg·m²)
Mtotal masskilogram (kg)
ddistance between the two parallel axesmeter (m)

Rearranged to find another variable:

Icm=I−Md2d=I−IcmMM=I−Icmd2

Valid for: the axes must be parallel and one must pass through the center of mass.

Example 1 A meter stick swinging from one end

A uniform rod has a mass of 1.2 kg and a length of 0.90 m. Its moment of inertia about its center is ML²/12. What is its moment of inertia about a parallel axis through one end?

  1. Given:
    • total mass: M=1.2 kg
    • L: L=0.9 m
  2. Formula: I=112ML2+M(L2)2
  3. Substitute: M=1.2 kg,L=0.9 m
  4. Answer: I=0.324 kg·m2

The result equals ML²/3, four times the value about the center, which is why the end-pivot formula for a rod has 1/3 in it.

Why Does the Parallel Axis Theorem Work?

Think of the object as many small masses mi. The moment of inertia about any axis is ∑miri2, where ri is each mass's distance from that axis. Measure each position from the center of mass, then shift every one by the same vector d→ to reach the new axis.

Squaring the shifted distances gives three groups of terms. The first group, ∑miri2 measured from the center, is just Icm. The last group, ∑mid2, is Md2. The middle group is 2d→⋅∑mir→i, and by the definition of the center of mass, ∑mir→i=0 when positions are measured from it.

So the cross term vanishes and only Icm+Md2 is left. This short proof also shows why one axis must go through the center of mass: from any other starting point, the middle term would not cancel.

How Does the Theorem Change the Moments of Inertia of Common Shapes?

Applying the theorem to the standard shapes gives a family of results you will meet again and again. A thin rod about its center has I=112ML2; shift the axis to one end, a distance L/2, and it becomes 13ML2. A solid disk about its center has 12MR2; about an axis on its rim it has 32MR2.

The table lists these and other common cases. In every row the new coefficient equals the old coefficient plus the square of the shift measured in units of the size. That makes the table easy to rebuild from memory.

Example 2 A disk spinning about a point on its rim

A solid disk of mass 4.0 kg and radius 0.15 m is pinned so it rotates about an axis through its rim, parallel to its central axis. Its moment of inertia about the center is MR²/2. Find its moment of inertia about the rim axis.

  1. Given:
    • total mass: M=4 kg
    • R: R=0.15 m
  2. Formula: I=12MR2+MR2
  3. Substitute: M=4 kg,R=0.15 m
  4. Answer: I=0.135 kg·m2

Moving the axis a distance of one radius triples the moment of inertia, giving 3MR²/2.

Moments of inertia about the center of mass and about a shifted parallel axis
ShapeI about center of massNew axisShift dI about new axis
Thin rod, length LML²/12Perpendicular, through one endL/2ML²/3
Thin rod, length LML²/12Perpendicular, a quarter of the way alongL/47ML²/48
Solid disk or cylinder, radius RMR²/2Parallel to the symmetry axis, through the rimR3MR²/2
Thin hoop, radius RMR²Parallel to the symmetry axis, through the rimR2MR²
Solid sphere, radius R2MR²/5Tangent to the surfaceR7MR²/5
Thin hollow sphere, radius R2MR²/3Tangent to the surfaceR5MR²/3
Any object, size much smaller than dsmallFar from the objectdabout Md² (point mass)
Source: Computed with I = I_cm + Md² from the center-of-mass formulas in our formula data · Retrieved October 2026

Where Is the Parallel Axis Theorem Used?

Doors are a classic case. A 30 kg door 0.9 m wide behaves like a rod for rotation about a vertical axis, so swinging it on its hinges takes a moment of inertia of about 8.1 kg·m², four times the 2.0 kg·m² it would have about a vertical line through its middle (computed). That is why heavy doors need a firm push to get moving.

Engineers use the theorem to build up complex parts. A machine with a 2.0 kg disk of radius 0.10 m mounted 0.30 m from its main shaft has I=0.01+0.18=0.19 kg·m² about the shaft (computed). Notice that the Md2 part dominates. When an object is small compared with its distance from the axis, treating it as a point mass is a good shortcut.

Biomechanics uses the theorem to model limbs swinging about the hip or shoulder, and gymnasts feel it every time they tuck or stretch out on a bar. The theorem also underlies the physical pendulum, where any rigid body swinging about a pivot follows T=2πI/(Mgd) with I from the parallel axis theorem.

Example 3 Finding a bat's center-of-mass value from a swing test

A 0.90 kg baseball bat hangs from a pivot at its handle. A swing test gives a moment of inertia of 0.205 kg·m² about the pivot, and its center of mass is 0.42 m from the pivot. What is its moment of inertia about a parallel axis through the center of mass?

  1. Given:
    • moment of inertia about the new axis: I=0.205 kg·m2
    • total mass: M=0.9 kg
    • distance between the two parallel axes: d=0.42 m
  2. Formula: Icm=I−Md2
  3. Substitute: I=0.205 kg·m2,M=0.9 kg,d=0.42 m
  4. Answer: Icm=0.04624 kg·m2

Most of the pivot value comes from the Md² term; the bat's own spread of mass about its center contributes less than a quarter.

Heavy wooden door swinging open on its hinges, rotating about an axis at its edge rather than its center
A door turns about its hinges, not its middle, so its moment of inertia is four times the center value.

How Does the Pivot Point Change the Swing of a Rod?

Hang a 1.0 m rod from different points and time its swing. With the pivot at the end, the period is about 1.64 s, noticeably shorter than the 2.01 s of a simple pendulum of the same length (computed). The rod's mass is spread along its length, so it acts like a shorter pendulum.

Move the pivot toward the center and something surprising happens. The period first drops to a minimum of about 1.52 s when the pivot is about 0.29 m from the center, then rises again, reaching nearly 2 s at 0.1 m and growing without limit as the pivot reaches the center (computed). Close to the center, gravity's turning effect becomes tiny while Icm stays the same, so the swing slows dramatically.

The table and graphs show these results. They come straight from combining the parallel axis theorem with Newton's second law for rotation.

Swing period of a uniform 1.0 m, 1.0 kg rod for different pivot points (small swings)
Pivot distance from center d (m)I about pivot (kg·m²)Period T (s)
0.50 (end of rod)0.33331.638
0.400.24331.565
0.300.17331.525
0.2887 (minimum period)0.16671.525
0.200.12331.576
0.100.09331.938
0.050.08582.629
0.020.08374.105
Source: Computed with I = ML²/12 + Md² and T = 2π√(I/(Mgd)), g = 9.80665 m/s² (standard acceleration of gravity, CODATA 2022) · Retrieved October 2026
Graph of swing angle for a 1 m rod pivoted at its end and a 1 m simple pendulum, the rod swinging with a shorter period
Released at 10°, the rod (I = ML²/3 from the parallel axis theorem) swings with a period of 1.64 s, against 2.01 s for a simple pendulum.
Graph comparing the swing of a 1 m rod pivoted at its end and 0.1 m from its center, the second swinging more slowly
With the pivot 0.10 m from the center, the rod swings more slowly (1.94 s) than with the pivot at its end (1.64 s).

Who Discovered the Parallel Axis Theorem?

The theorem has no single recorded discovery date. It carries the names of two scientists. The Dutch physicist Christiaan Huygens worked out how compound pendulums swing in the 1600s, and reasoning equivalent to the theorem appears in that work. The Swiss mathematician Jakob Steiner, working in the 1800s, is credited with a general geometric treatment, which is why it is often called Steiner's theorem.

The modern form, written with moments of inertia and the center of mass, grew out of the development of rigid-body mechanics in the 1700s and 1800s and is now a standard tool in every engineering and physics course.

Going Deeper: When Can You Not Use the Parallel Axis Theorem?

The theorem only connects an axis through the center of mass with a parallel axis. To move between two axes that both miss the center of mass, go through the center first: subtract Md12, then add Md22. Simply adding M(d2−d1)2 gives the wrong answer.

It also says nothing about axes at an angle. For tilted axes you need the full inertia tensor. For flat objects there is a separate tool, the perpendicular axis theorem, which states that Iz=Ix+Iy for a thin plate lying in the xy-plane. The two theorems are often combined, for example to find the moment of inertia of a disk about a diameter.

How Can You Practice Parallel Axis Theorem Problems?

Try rebuilding the shape table yourself, then work through the rotation problems in our torque worksheets. The rotational motion formulas sheet lists every moment of inertia you need, and the rotational motion calculator checks your numbers. Then take the quiz below.

Common Misconceptions

Myth: You can use the theorem between any two parallel axes by adding M times the distance between them squared.

Physics: One of the axes must pass through the center of mass. For two off-center axes, subtract Md₁² to reach the center, then add Md₂².

Myth: Moving the axis can make the moment of inertia smaller than I_cm.

Physics: Md² is never negative, so I is always at least I_cm. The center of mass gives the minimum.

Myth: The distance d is measured along the object.

Physics: d is the perpendicular distance between the two parallel axes, which can differ from a distance measured along a tilted or curved object.

Myth: The theorem works for axes at any angle.

Physics: It only applies to parallel axes. Tilted axes need the full inertia tensor, and flat plates can use the perpendicular axis theorem.

Key Facts

  • The parallel axis theorem states I = I_cm + Md² for two parallel axes, one through the center of mass.
  • The moment of inertia of any object is smallest about an axis through its center of mass.
  • A thin rod has ML²/12 about its center and ML²/3 about one end, a factor of four.
  • Moving between two axes that both miss the center of mass requires going through the center of mass first.
  • The cross term in the proof vanishes because positions measured from the center of mass sum to zero when weighted by mass.
  • For objects small compared with their distance from the axis, Md² dominates and the point-mass formula is a good estimate.
  • The theorem is also called the Huygens–Steiner theorem.
Did you know? A uniform rod swings fastest when the pivot sits about 29% of its length from the center, not at its end; at that point the rod's period is shorter than at any other pivot (computed).

Quick Quiz: How Well Do You Know Parallel Axis Theorem?

6 questions. Tap an answer to check it.

  1. What does the parallel axis theorem state?

  2. Which axis gives the smallest moment of inertia for a given direction?

  3. A rod's moment of inertia about its center is ML²/12. What is it about one end?

  4. A 2 kg object has I_cm = 0.1 kg·m². What is I about a parallel axis 0.5 m away?

  5. What must be true of the two axes in the theorem?

  6. If the axis is moved twice as far from the center of mass, the added term Md² becomes

Frequently Asked Questions

What is the parallel axis theorem in simple words?

The parallel axis theorem is a shortcut for finding how hard an object is to spin about a new axis. Start with its moment of inertia about an axis through its center of mass, then add its mass times the square of how far you moved the axis. The farther the new axis is from the center, the harder the object is to spin.

What is the formula for the parallel axis theorem?

The formula is I = I_cm + Md². I is the moment of inertia about the new axis, I_cm is the moment of inertia about a parallel axis through the center of mass, M is the total mass and d is the perpendicular distance between the two axes. With mass in kilograms and distance in meters, the answer is in kilogram meters squared.

When can you use the parallel axis theorem?

You can use it whenever the two axes are parallel and one of them passes through the object's center of mass. The object must be rigid, but it can have any shape. It cannot connect axes at an angle to each other, and it cannot jump directly between two axes that both miss the center of mass.

Why is the moment of inertia smallest about the center of mass?

The theorem adds Md² to the center-of-mass value for every other parallel axis, and Md² is always positive unless d is zero. So any shift away from the center of mass increases the moment of inertia. Physically, moving the axis carries the whole mass around a larger circle, which takes more effort to start and stop.

How do you find the moment of inertia of a rod about its end?

Start from the rod's value about its center, ML²/12. The end is a distance L/2 from the center, so add M(L/2)², which is ML²/4. The sum is ML²/12 + 3ML²/12 = ML²/3. For a 1.2 kg rod 0.9 m long, that gives 0.324 kg·m², four times the value about the center.

What is the difference between the parallel axis and perpendicular axis theorems?

The parallel axis theorem shifts an axis sideways and works for any rigid body. The perpendicular axis theorem relates three mutually perpendicular axes through one point and works only for flat, thin objects: the moment of inertia about the axis perpendicular to the plate equals the sum of the moments about two axes lying in the plate.

Who discovered the parallel axis theorem?

No single person or date is recorded. The theorem is named after Christiaan Huygens, who studied swinging compound pendulums in the 1600s, and Jakob Steiner, a Swiss mathematician of the 1800s. That is why you may see it called the Huygens–Steiner theorem or simply Steiner's theorem in older textbooks and in European courses.

Can d be zero in the parallel axis theorem?

Yes. If d is zero, the new axis is the center-of-mass axis itself, and the formula gives I = I_cm, as it should. As d grows from zero, the moment of inertia grows with the square of the distance, so small shifts add little while large shifts add a lot.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.