Simple machine

Lever

A lever is a rigid bar that pivots on a fixed point called the fulcrum, letting a small force applied far from the pivot move a large load close to it. Crowbars, seesaws, scissors and even your forearm are levers. A lever can multiply force, multiply distance and speed, or simply change the direction of a push.

Person using a long pry bar over a log to lift a heavy boulder, a lever multiplying a small force into a large one
A long bar resting on a log turns a modest push into enough force to tip a heavy boulder.

At a Glance

A lever is a simple machine made of a rigid bar turning on a fulcrum. It balances when effort × effort arm = load × load arm, so its mechanical advantage is MA = F_out / F_in = effort arm / load arm, and a longer effort arm means less force is needed to lift the load.

Type
One of the six classic simple machines
Parts
Rigid bar, fulcrum (pivot), effort, load
Law of the lever
Effort × effort arm = load × load arm
Mechanical advantage
MA = Fout ÷ Fin = effort arm ÷ load arm
Classes
Class 1, class 2 and class 3, by the order of the parts
First explained by
Archimedes, 3rd century BC
On this page
  1. What Is a Lever?
  2. What Are the Parts of a Lever?
  3. How Does a Lever Work, Step by Step?
  4. What Is the Law of the Lever?
  5. What Are the Three Classes of Levers?
  6. How Is a Lever Related to Torque?
  7. Where Are Levers Used in Everyday Life?
  8. Who Discovered the Law of the Lever?
  9. How Can You Practice Lever Problems?
  10. Common Misconceptions
  11. Key Facts
  12. Quiz
  13. FAQ

What Is a Lever?

A lever is a stiff bar that can turn around a support. Push on one part of the bar and another part moves, often with a different force and a different speed. The support it turns on is the fulcrum, the force you apply is the effort, and the object being moved is the load.

The lever is one of the six classic simple machines and probably the oldest. A stick wedged under a rock is a lever, and so is a modern excavator arm. What makes it useful is that the distances from the fulcrum control the forces. Put the fulcrum close to the load and a small push can move something very heavy.

Levers are everywhere once you start looking: bottle openers, door handles, oars, tweezers, staplers and the bones and muscles of your own body. Our lever examples page sorts dozens of them by class.

What Are the Parts of a Lever?

  • The bar (or arm): the rigid part that turns. It must not bend much, or some of your effort is wasted in flexing it.
  • The fulcrum: the fixed pivot point the bar rotates around, such as the middle support of a seesaw or the hinge of a pair of pliers.
  • The effort: the input force you or a muscle or motor applies.
  • The load: the output force the lever exerts on the object, also called the resistance.
  • The effort arm: the distance from the fulcrum to where the effort acts.
  • The load arm: the distance from the fulcrum to where the load acts.

Strictly speaking, each arm is the perpendicular distance from the fulcrum to the line along which the force acts. That distance is called the lever arm, and it matters whenever forces push at a slant.

How Does a Lever Work, Step by Step?

  1. You apply an effort to one point on the bar, a certain distance from the fulcrum.
  2. The effort creates a turning effect, called a moment or torque, equal to the force times its distance from the fulcrum.
  3. The load resists with its own turning effect in the opposite direction, equal to the load force times its distance from the fulcrum.
  4. The bar balances when the two turning effects are equal. Push a little harder and the load begins to move.
  5. The ends move different distances. The end farther from the fulcrum sweeps through a bigger arc, so if your effort arm is long, your hand moves a long way while the load moves only a little.

The diagram shows a class 1 lever where a 200 N push 1.5 m from the fulcrum balances a 600 N load 0.5 m away.

Class 1 lever diagram with the fulcrum between a 600 N load 0.5 m away and a 200 N effort 1.5 m away
A class 1 lever: a 200 N push 1.5 m from the fulcrum balances a 600 N load 0.5 m away.

What Is the Law of the Lever?

The law of the lever says that a lever balances when the effort times its distance from the fulcrum equals the load times its distance from the fulcrum: Fidi=Fodo. Rearranged, the force multiplication is Fo/Fi=di/do. A bar with an effort arm three times longer than its load arm lets you hold a load three times your push.

That ratio is the lever's mechanical advantage. A value above 1 means the lever multiplies force. A value below 1 means it gives up force in exchange for a larger, faster movement at the load end. Our mechanical advantage calculator works out effort, load or arm length for any lever.

No lever gives you free energy. When it multiplies force, the load moves a shorter distance than your hand, so the work in equals the work out for an ideal lever. Real levers lose a little to friction at the fulcrum and bending of the bar.

Mechanical advantage compares the force the lever delivers to the load with the force you put in. Here it is with each symbol and its unit.

MA=FoFi
What each symbol means
SymbolQuantitySI unit
MAmechanical advantagedimensionless (1)
Fooutput force (exerted on the load)newton (N)
Fiinput force (effort)newton (N)

Rearranged to find another variable:

Fo=MA⋅FiFi=FoMA

Valid for: for a lever in equilibrium MA = l_i / l_o (input arm / output arm).

Example 1 Prying up a paving stone with a crowbar

A gardener presses down on a crowbar with a force of 150 N, and the short end lifts the edge of a paving stone with a force of 900 N. What is the crowbar's mechanical advantage?

  1. Given:
    • output force (exerted on the load): Fo=900 N
    • input force (effort): Fi=150 N
  2. Formula: MA=FoFi
  3. Substitute: Fo=900 N,Fi=150 N
  4. Answer: MA=6

That ratio also tells you the effort arm is about six times longer than the load arm, if friction at the pivot is small.

Effort needed to balance a 600 N load for different arm lengths (ideal lever)
Effort arm (m)Load arm (m)Effort needed (N)Mechanical advantage
0.50.56001.00
1.00.53002.00
1.50.52003.00
2.00.25758.00
0.30.91,8000.33
Source: Computed with effort = load × load arm ÷ effort arm; no friction at the fulcrum · Retrieved October 2026

What Are the Three Classes of Levers?

Levers are sorted into three classes by which part sits in the middle. Our full guide to the classes of levers goes into each one with more examples.

  • Class 1: fulcrum in the middle. The effort and load are on opposite sides, and the load moves the opposite way from your push. Seesaws, crowbars, scissors and pliers belong here. Depending on where the fulcrum sits, they can multiply force or distance.
  • Class 2: load in the middle. The fulcrum is at one end and the effort at the other, so the effort arm is always longer than the load arm. That gives a mechanical advantage above 1, as in wheelbarrows, nutcrackers and bottle openers.
  • Class 3: effort in the middle. The effort acts between the fulcrum and the load, so the effort arm is always shorter. These levers need more force than the load but move it farther and faster: tweezers, fishing rods, brooms and most limbs of the human body.

The second and third diagrams show a class 2 and a class 3 lever, so you can compare the arm lengths and forces directly.

Example 2 Lifting a loaded wheelbarrow

A wheelbarrow acts as a class 2 lever with a mechanical advantage of 4. Its load of soil and the barrow press down with 800 N. How much upward force must you apply at the handles?

  1. Given:
    • output force (exerted on the load): Fo=800 N
    • mechanical advantage: MA=4
  2. Formula: Fi=FoMA
  3. Substitute: Fo=800 N,MA=4
  4. Answer: Fi=200 N

Placing the heaviest part of the load close to the wheel shortens the load arm, which raises the mechanical advantage further.

The three classes of levers compared
ClassMiddle partMechanical advantageMain benefitExamples
Class 1FulcrumAbove, below or equal to 1Changes direction; can multiply force or distanceSeesaw, crowbar, scissors, claw hammer
Class 2LoadAlways above 1Multiplies forceWheelbarrow, nutcracker, bottle opener
Class 3EffortAlways below 1Multiplies distance and speedTweezers, broom, fishing rod, forearm
Source: Follows from the positions of fulcrum, effort and load and the law of the lever · Retrieved October 2026
Class 2 lever diagram with an 800 N load 0.3 m from the fulcrum and the upward effort at 1.2 m, mechanical advantage 4
A class 2 lever like a wheelbarrow: the load sits between the fulcrum and the effort, giving a mechanical advantage of 4.

How Is a Lever Related to Torque?

Every lever is really a torque machine. Torque measures how strongly a force tends to turn something around a pivot, and it equals the force times its lever arm: τ=rFsin⁡θ. The law of the lever is simply the statement that the torque from the effort balances the torque from the load.

This view explains why the direction of your push matters. Push straight along the bar toward the fulcrum and nothing turns, because the angle is zero. Push at a right angle to the bar and you get the largest possible turning effect. That is why you pull a wrench handle sideways rather than along its length. The torque calculator handles any angle.

Example 3 Turning effect of a push on a long handle

A mechanic pushes at a right angle (θ = 90°, or 1.5708 rad) on the end of a breaker bar with a force of 120 N, 0.45 m from the center of a stuck bolt. What torque does the push create?

  1. Given:
    • distance from pivot to point where force acts: r=0.45 m
    • magnitude of the force: F=120 N
    • angle between r and F: θ=1.571 rad
  2. Formula: τ=rFsin⁡θ
  3. Substitute: r=0.45 m,F=120 N,θ=1.571 rad
  4. Answer: τ=54 N·m

Doubling the handle length would double the torque with the same push, which is the lever principle at work.

Where Are Levers Used in Everyday Life?

At home, levers open cans, crack nuts, cut paper and lift lids. A claw hammer pulling a nail is a class 1 lever with a long handle and a very short load arm, which is why a modest pull removes a nail that you could never pull with your fingers.

Your body is full of levers too. When you raise a cup, your elbow is the fulcrum, the biceps muscle pulls just below it, and the cup sits in your hand far away. That is a class 3 lever: the muscle must pull much harder than the weight of the cup, but your hand moves quickly over a wide arc. Standing on tiptoe uses the ball of your foot as a fulcrum in a class 2 arrangement.

Heavy industry relies on levers inside cranes, excavator arms, car jacks and brake pedals. Many larger machines combine a lever with other simple machines; see compound machines and the closely related wheel and axle.

Class 3 lever diagram like a forearm, effort 0.05 m from the fulcrum lifting a 20 N load 0.35 m away
A class 3 lever like your forearm: the muscle pulls with far more force than the load, but the hand moves much farther.
Adult sitting near the pivot balancing a small child at the far end of a seesaw, showing the law of the lever
A heavier rider sits closer to the pivot so the seesaw balances, exactly as the law of the lever predicts.

Who Discovered the Law of the Lever?

Levers were in use long before anyone wrote down why they worked. Farmers used long poles to lift water from rivers, and builders pried heavy stones into place with wooden beams.

The first known proof of the law of the lever comes from the Greek mathematician Archimedes, in his work On the Equilibrium of Planes from the 3rd century BC. He showed that weights balance at distances inversely proportional to their sizes. He is also said to have boasted that, given a long enough lever and somewhere to stand, he could shift the Earth itself, a vivid way of saying that any force can be multiplied without limit if the arm is long enough.

How Can You Practice Lever Problems?

For every lever, label the fulcrum, effort and load, measure both arms from the fulcrum, then apply effort × effort arm = load × load arm. Our levers worksheets include printable sets on identifying classes and calculating forces, with answer keys. Younger students can start with levers for kids, then everyone can try the quiz below.

Common Misconceptions

Myth: A lever lets you do less work.

Physics: A lever lets you use less force, not less work. The smaller force moves through a longer distance, so the work in is at least the work out.

Myth: Every lever makes lifting easier.

Physics: Class 3 levers, like tweezers and your forearm, need more force than the load. Their benefit is a bigger, faster movement, not a smaller effort.

Myth: The fulcrum of a lever is always in the middle.

Physics: Only class 1 levers have the fulcrum between effort and load. In class 2 and class 3 levers the fulcrum is at one end.

Key Facts

  • A lever is a rigid bar that turns around a fixed pivot called the fulcrum.
  • The law of the lever states that effort times effort arm equals load times load arm when the lever balances.
  • Mechanical advantage of a lever equals the effort arm divided by the load arm.
  • Levers come in three classes depending on whether the fulcrum, load or effort sits in the middle.
  • Class 2 levers always multiply force, while class 3 levers always multiply distance and speed.
  • An ideal lever never creates energy: a smaller force must move through a larger distance.
  • Archimedes gave the first known proof of the law of the lever in the 3rd century BC.
Did you know? Most of the levers in your body are class 3 levers that work at a mechanical disadvantage, so your muscles often pull with several times the force of the object you are holding, in exchange for fast, wide movements of your hands and feet.

Quick Quiz: How Well Do You Know Lever?

6 questions. Tap an answer to check it.

  1. What is the fixed pivot point of a lever called?

  2. In which class of lever is the load between the fulcrum and the effort?

  3. A lever has an effort arm of 1.2 m and a load arm of 0.3 m. What is its ideal mechanical advantage?

  4. Which of these is a class 3 lever?

  5. What does a lever with a mechanical advantage below 1 give you?

  6. Who gave the first known proof of the law of the lever?

Frequently Asked Questions

What is a lever in simple words?

A lever is a stiff bar that turns on a pivot point called a fulcrum. When you push down on one part of the bar, another part moves up or down. By choosing where the fulcrum goes, you can lift heavy things with a small push or make something move far and fast. Seesaws, crowbars and bottle openers are levers.

What are the three parts of a lever?

The three main parts are the fulcrum, the effort and the load. The fulcrum is the pivot point the bar turns on. The effort is the force you apply to make the lever move. The load is the object being moved or the resistance being overcome. The rigid bar connects all three, and the distances from the fulcrum to the effort and load set how much the force is multiplied.

What is the formula for a lever?

The law of the lever is effort times effort arm equals load times load arm. From it, the mechanical advantage is the load divided by the effort, which also equals the effort arm divided by the load arm. For example, an effort arm of 2 meters and a load arm of 0.5 meters gives a mechanical advantage of 4, so a 100 newton push balances a 400 newton load.

What are the 3 classes of levers?

In a class 1 lever, the fulcrum sits between the effort and the load, as in a seesaw or scissors. In a class 2 lever, the load sits between the fulcrum and the effort, as in a wheelbarrow. In a class 3 lever, the effort sits between the fulcrum and the load, as in tweezers or a fishing rod. The middle part names the class.

How does a lever make work easier?

A lever lets you trade distance for force. If your hand is far from the fulcrum and the load is close to it, your hand moves a long way while the load moves only a little, and in exchange the lever multiplies your force. The total work stays about the same, but you can lift something far heavier than you could with your bare hands.

How do you find the mechanical advantage of a lever?

Divide the output force on the load by the input force you apply; that ratio is the mechanical advantage. For an ideal lever it also equals the effort arm divided by the load arm. A value greater than 1 means the lever multiplies force, while a value less than 1 means it multiplies distance and speed instead, as in class 3 levers.

Why are scissors a lever?

Scissors are two class 1 levers joined at a shared pivot, the screw in the middle, which acts as the fulcrum. Your fingers apply the effort at the handles, and the blades apply the load to the paper or cloth. Cutting tough material close to the pivot shortens the load arm and gives a bigger mechanical advantage, which is why thick cardboard is easier to cut near the hinge.

Is the human arm a lever?

Yes. When you bend your elbow to lift something, the elbow joint is the fulcrum, the biceps muscle supplies the effort just a few centimeters from the joint, and the object in your hand is the load much farther away. That makes the forearm a class 3 lever. The muscle must pull much harder than the load weighs, but the hand moves quickly through a large arc.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.