
At a Glance
Stress is force per unit area, σ = F / A, measured in pascals (N/m²). Strain is the change in length divided by the original length, ε = ΔL / L₀, and has no unit. In the elastic region the two are proportional, and the ratio of stress to strain is Young's modulus.
- Stress symbol and unit
- σ (sigma), pascal (Pa = N/m²), often MPa
- Strain symbol and unit
- ε (epsilon), dimensionless (often given in %)
- Formulas
- σ = F / A and ε = ΔL / L₀
- Main types
- Tensile, compressive, shear and bulk (volume)
- Link between them
- Young's modulus Y = σ / ε in the elastic region
On this page
- What Are Stress and Strain in Physics?
- Stress and Strain Explained Simply
- How Do You Calculate Stress?
- What Is Strain and How Do You Find It?
- What Are the Types of Stress?
- What Does the Stress-Strain Curve Show?
- How Are Stress and Strain Related?
- Where Do Stress and Strain Matter in Everyday Life?
- Where Can You Practice Stress and Strain Problems?
- Common Misconceptions
- Key Facts
- Quiz
- FAQ
What Are Stress and Strain in Physics?
Stress is the internal force per unit area inside a loaded solid, and strain is how much the solid deforms relative to its original size. Hang a heavy bag from a wire and the wire is under stress. Measure it carefully and you will find it has grown a tiny bit longer: that fractional stretch is the strain.
Why not simply talk about force and stretch? Because a force alone says little about whether something will break. A 1,000 N pull is nothing for a thick steel bar but enough to snap a thin wire. Dividing by area puts every object on the same footing, so a lab test on a small sample tells you how a full-size beam of the same material will behave.
Stress and strain are the language of elasticity, the branch of physics that studies how solids deform and spring back. They are also the working tools of every civil, mechanical and aerospace engineer.
Stress and Strain Explained Simply
Think of a solid as a crowd of atoms joined by tiny springs. When you pull on the ends, every little spring in the cross-section shares the load. Stress is the load each patch of that cross-section has to hold. A thicker rod has more springs side by side, so each one does less work and the stress is lower.
Strain is about the springs along the length. If every bond stretches by the same small fraction, a long rod grows by more millimeters than a short one, but the fraction is identical. That fraction is the strain. So stress is the cause, measured per area, and strain is the effect, measured per length.

How Do You Calculate Stress?
To find stress, divide the force by the cross-sectional area that carries it:
The SI unit is the pascal, one newton per square meter. A pascal is a very small stress, so engineers usually quote megapascals (MPa, millions of pascals) or gigapascals (GPa). The units match those of pressure, and the two ideas are related. Pressure is a push spread over a surface, while stress is the load carried inside a solid, which can pull, push or shear. Our force vs pressure comparison shows why dividing by area matters so much.
The table below shows the same 1,000 N load hung from round steel wires of different diameters. Halving the diameter quarters the area, so the stress rises four times. The thinnest wire could not really carry this load: even the strongest steel wire breaks well below 5,000 MPa, so the 0.5 mm wire would snap.
Here is the stress formula with each variable and its SI unit, plus the two rearranged forms for the force and the area.
| Symbol | Quantity | SI unit |
|---|---|---|
| stress (tensile or compressive) | pascal (Pa) | |
| force applied perpendicular to the area | newton (N) | |
| cross-sectional area | square meter (m²) |
Rearranged to find another variable:
Example 1 Stress in a tow strap
A flat nylon tow strap is 50 mm wide and 2 mm thick, so its cross-section is 0.0001 m². While pulling a stuck car it carries a tension of 6,000 N. What tensile stress is the strap under, in megapascals?
- Given:
- force applied perpendicular to the area:
- cross-sectional area:
- force applied perpendicular to the area:
- Formula:
- Substitute:
- Answer:
One megapascal is one million pascals, so the strap material feels a load of millions of newtons for every square meter of its cross-section.
| Wire diameter | Cross-sectional area (m²) | Stress (MPa) |
|---|---|---|
| 0.5 mm | 1.963 × 10⁻⁷ | 5,093 |
| 1 mm | 7.854 × 10⁻⁷ | 1,273 |
| 2 mm | 3.142 × 10⁻⁶ | 318.3 |
| 5 mm | 1.963 × 10⁻⁵ | 50.93 |
| 10 mm | 7.854 × 10⁻⁵ | 12.73 |
| Source: Computed with A = πd²/4 and σ = F/A for F = 1,000 N · Retrieved October 2026 | ||
What Is Strain and How Do You Find It?
Strain is the change in length divided by the original length:
A positive strain means the object got longer (tension); a negative strain means it got shorter (compression). Measuring strain on a real structure is surprisingly easy. Engineers glue thin foil strain gauges to bridges, aircraft wings and wind turbine blades. As the surface stretches, the foil stretches with it and its electrical resistance changes, giving a live reading of the strain.
Example 2 Strain in a suspension bridge cable
A steel hanger cable on a footbridge is 120 m long when unloaded. When a crowd walks across, it stretches by 0.06 m. What is the strain in the cable?
- Given:
- change in length:
- original length:
- change in length:
- Formula:
- Substitute:
- Answer:
That is five hundredths of one percent, a typical working strain for steel well inside its elastic range.
What Are the Types of Stress?
Stress is grouped by the direction of the force relative to the surface that carries it:
- Tensile stress pulls the material apart, as in a crane cable, a guitar string or a rope under tension. It produces a lengthening strain.
- Compressive stress squeezes the material together, as in a table leg, a brick wall or a pillar. It produces a shortening strain.
- Shear stress acts parallel to a surface, trying to slide one layer over the next, as when scissors cut paper or a bolt holds two plates that are pulled sideways.
- Bulk (volume) stress squeezes an object equally from every side, as deep water does to a submarine hull. It changes volume instead of length.
Shear and bulk stress have their own stiffness constants, covered on our shear and bulk modulus page. Many real parts feel more than one type at once: a bent ruler is stretched on its outer face and squeezed on its inner face.
Example 3 Compressive stress in a concrete pillar
A square concrete pillar measures 0.3 m by 0.3 m, so its cross-section is 0.09 m². It supports a floor load of 450,000 N. What compressive stress does the pillar carry, in megapascals?
- Given:
- force applied perpendicular to the area:
- cross-sectional area:
- force applied perpendicular to the area:
- Formula:
- Substitute:
- Answer:
Ordinary concrete can typically take several times this in compression, which is why designers like it for columns but add steel bars wherever it will be pulled.
| Type | Force direction | Resulting strain | Everyday example |
|---|---|---|---|
| Tensile | Perpendicular to the cut, pulling outward | Longer (ε > 0) | Elevator cable |
| Compressive | Perpendicular to the cut, pushing inward | Shorter (ε < 0) | Table leg |
| Shear | Parallel to the surface | Layers slide, shape tilts | Scissors cutting paper |
| Bulk | Equal from all sides | Volume shrinks | Submarine hull at depth |
| Source: Summary of standard definitions · Retrieved October 2026 | |||

What Does the Stress-Strain Curve Show?
If you pull a metal sample in a testing machine and plot stress against strain, you get the stress-strain curve, the fingerprint of a material. Its main features, in order, are:
- The linear region. Stress and strain rise together in a straight line. This is Hooke's law for materials, and the slope of the line is Young's modulus.
- The elastic limit. Up to this point the sample returns to its original length when unloaded. Beyond the elastic limit, some stretch becomes permanent.
- The yield point. The material starts to flow, gaining a lot of strain for little extra stress.
- Ultimate strength. The highest stress the sample can carry. After it, the sample develops a narrow waist, called necking.
- Fracture. The sample breaks.
The difference between springing back and staying bent is the subject of our elastic and plastic deformation page. Brittle materials such as glass and cast iron skip most of these stages and snap soon after the linear region.

How Are Stress and Strain Related?
In the linear region, stress is proportional to strain, and the constant that links them is the elastic modulus:
This is the same idea Robert Hooke expressed for springs in 1678, scaled so that it describes the material instead of one particular object. Hooke's spring constant k depends on the length and thickness of the spring; the modulus does not. You can see the connection by writing
A stretched solid also stores energy, just as a spring does. That stored energy is the subject of elastic potential energy.
Where Do Stress and Strain Matter in Everyday Life?
- Bridges and buildings. Designers keep working stresses well below the yield strength, often by a factor of two or more, so that wind, crowds and aging never push the steel into permanent bending.
- Bones. Your thigh bone carries compressive stress every time you take a step. Bone slowly thickens where stress is high, which is one reason exercise strengthens the skeleton.
- Railway tracks. Steel rails heat up in summer. If they are clamped so they cannot grow, the blocked thermal expansion shows up as a large compressive stress.
- Climbing ropes. A dynamic rope is designed to take a large strain during a fall, spreading the stop over a longer distance so the force on the climber stays low.
- Airplane wings. The lower skin of a wing is in tension and the upper skin in compression during flight, and strain gauges track both on test aircraft.
Where Can You Practice Stress and Strain Problems?
Start with the worked examples above, then try your own numbers. Our Young's modulus formula page shows how to predict how far a wire stretches from its stress. For the spring version of the same idea, use the Hooke's law calculator and the printable Hooke's law worksheets. Because stress and pressure share a unit, the pressure calculator is handy for quick force-over-area checks.
Common Misconceptions
Myth: A bigger force always means a bigger stress.
Physics: Stress depends on area too. A large force spread over a thick beam can produce less stress than a small force concentrated in a thin wire.
Myth: Strain is measured in meters.
Physics: Strain is a ratio of two lengths, so the units cancel. A stretch of 1 mm on a 1 m rod and 1 cm on a 10 m rod give the same strain.
Myth: Stress and pressure are exactly the same thing.
Physics: They share the pascal, but pressure is a push spread over a surface, usually from a fluid. Stress is the internal load inside a solid and can be a pull or a sideways shear as well as a push.
Myth: If an object is not moving, nothing inside it is stressed.
Physics: A bridge cable at rest has zero net force on it, yet it is under high tensile stress because it is pulled equally from both ends.
Key Facts
- Stress is force divided by cross-sectional area, σ = F / A, measured in pascals.
- Strain is the change in length divided by the original length, ε = ΔL / L₀, and has no unit.
- Tensile stress stretches a material, compressive stress shortens it, shear stress slides layers and bulk stress shrinks volume.
- In the elastic region stress is proportional to strain, and the ratio is Young's modulus.
- Past the elastic limit a material keeps part of its deformation permanently.
- The same force produces four times the stress in a wire with half the diameter.
- Strain gauges measure strain on real structures through a change in electrical resistance.
Quick Quiz: How Well Do You Know Stress and Strain?
6 questions. Tap an answer to check it.
What is the SI unit of stress?
Stress is force per area, so its unit is newtons per square meter, the pascal.
A rod 4 m long stretches by 2 mm. What is the strain?
Strain = 0.002 m ÷ 4 m = 0.0005, a pure number.
If a wire's diameter is halved while the load stays the same, the stress becomes:
Area depends on the diameter squared, so halving the diameter quarters the area and quadruples the stress.
Which type of stress acts parallel to a surface?
Shear stress tries to slide one layer of material over the next.
The slope of the straight part of a stress-strain graph is:
In the linear region σ = Yε, so the slope is Young's modulus.
What happens when a metal is loaded beyond its elastic limit?
Past the elastic limit part of the stretch is plastic and does not recover.
Frequently Asked Questions
What is the difference between stress and strain?
Stress is the cause and strain is the effect. Stress is the force per unit area acting inside a material, measured in pascals. Strain is the fractional change in shape or length that results, found by dividing the change in length by the original length. Strain has no unit. In the elastic region a material's stress and strain rise in direct proportion to each other.
What is the formula for stress?
The formula for stress is σ = F / A, where σ is stress, F is the force acting at right angles to the cross-section and A is the area of that cross-section. With force in newtons and area in square meters, stress comes out in pascals. Rearranged, F = σA gives the force a part can carry at a given stress.
What is the formula for strain?
Strain is ε = ΔL / L₀, the change in length divided by the original length. Because both lengths use the same unit, strain is dimensionless. A 2 m rod that stretches by 1 mm has a strain of 0.0005, which can also be written as 0.05 percent or 500 microstrain. Shortening gives a negative strain.
What is the unit of stress?
The SI unit of stress is the pascal, equal to one newton per square meter. Because a pascal is tiny, engineers usually work in megapascals (MPa) and gigapascals (GPa). In the United States you will also see pounds per square inch, where one psi is about 6,895 pascals. Stress has the same units as pressure.
Why does strain have no unit?
Strain compares a length change with an original length, and both are measured in meters. Dividing meters by meters cancels the unit, leaving a pure number. That is useful: a strain of 0.001 means the same thing whether you measured in meters, inches or millimeters, so results from different labs and countries can be compared directly.
What is a stress-strain curve?
A stress-strain curve is a graph of the stress applied to a sample against the strain it produces, recorded as the sample is slowly pulled to failure. It starts with a straight elastic section whose slope is Young's modulus, then shows the yield point, the maximum or ultimate stress and finally fracture. Each material has its own characteristic shape.
What are the four types of stress?
The four main types are tensile stress, which pulls a material apart; compressive stress, which squeezes it; shear stress, which acts parallel to a surface and slides layers past each other; and bulk stress, which presses equally from every direction and changes volume. Bending and twisting combine these basic types inside the same part.
Is stress a vector or a scalar?
In introductory physics stress is treated as a single number for one direction, like a scalar. In full detail it is neither a scalar nor a simple vector but a tensor, because at any point it depends both on the direction of the force and on the orientation of the surface you consider. Engineers use the tensor form for complex parts.
How is stress related to Young's modulus?
Young's modulus is the ratio of tensile stress to tensile strain in the elastic region, Y = σ / ε. If you know the modulus of a material, you can predict the strain for any stress below the elastic limit, and from that the change in length. Steel has a modulus of roughly 200 GPa, so it stretches very little.
Sources
Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.








