How hydraulics multiply force

Pascal's Principle (Pascal's Law)

Pascal's principle states that a change in pressure applied to an enclosed fluid is passed on, undiminished, to every part of the fluid and to the walls of its container. Because pressure is force per area, a small push on a small piston becomes a large push on a large piston, which is how hydraulic lifts, jacks and car brakes multiply force.

Car raised on a polished hydraulic lift ram in a clean garage, an everyday use of Pascal's principle
A garage lift uses oil pressure from a small pump piston to push a wide ram up with enough force to hold a whole car.

At a Glance

Pascal's principle says pressure added to a confined fluid reaches every point of the fluid equally. For two connected pistons this gives F1 / A1 = F2 / A2, so the output force is F2 = F1 × (A2 / A1). A piston with 100 times the area delivers 100 times the force, but moves only one hundredth as far.

Discovered by
Blaise Pascal
Year
Established 1653, published 1663 after his death
Formula
F1/A1 = F2/A2
Quantity passed on
Pressure, in pascals (Pa = N/m²)
Applies to
Enclosed fluids at rest that barely compress, such as hydraulic oil and water
Main use
Hydraulic lifts, jacks, presses and brakes
On this page
  1. What Is Pascal's Principle?
  2. Pascal's Principle Explained Simply
  3. What Is the Formula for Pascal's Principle?
  4. How Does a Hydraulic Lift Work?
  5. Does Pascal's Principle Create Energy?
  6. Who Discovered Pascal's Principle?
  7. What Are Examples of Pascal's Principle in Everyday Life?
  8. When Does Pascal's Principle Not Apply Exactly?
  9. How Can You Practice Pascal's Principle Problems?
  10. Common Misconceptions
  11. Key Facts
  12. Quiz
  13. FAQ

What Is Pascal's Principle?

Pascal's principle, also called Pascal's law, describes what happens when you squeeze a fluid that is trapped in a closed container. Any extra pressure you add at one spot is felt everywhere else in the fluid, in full, at the same moment. Nothing is lost along the way, whatever the shape of the container or the length of the pipes.

Pressure is force divided by area. So if the same pressure acts on two pistons of different sizes, the bigger piston feels a bigger force. That simple fact is the whole secret of hydraulic machines, from a garage lift to the brakes in a car.

The principle is part of the wider study of pressure in fluids. It builds on the idea that a fluid at rest pushes equally in all directions at any point, the same idea behind hydrostatic pressure.

Pascal's Principle Explained Simply

Fill a plastic bottle to the brim with water, screw on the cap and poke a few small holes around its sides. Squeeze the middle of the bottle and water squirts out of every hole, not just the ones near your hand. Your squeeze raised the pressure of all the water at once.

Now imagine two syringes of different sizes joined by a tube of water. Press the thin plunger and the fat plunger rises. The water pressure is the same at both ends, but the fat plunger has much more area for that pressure to push on, so it pushes back with much more force. You trade a long, easy push for a short, strong one.

What Is the Formula for Pascal's Principle?

For two pistons sharing the same enclosed fluid, the pressure on each is equal: F1A1=F2A2. Here F1 is the input force on the small piston, A1 is its area, F2 is the output force on the large piston and A2 is its area. Forces are in newtons and areas in square meters.

Solving for the output force gives F2=F1A2A1. The ratio A2/A1 is the force multiplier of the machine, in the same way mechanical advantage describes a lever or pulley. Pistons are usually round, so the area ratio is the square of the diameter ratio: a piston with 10 times the diameter has 100 times the area.

The pressure itself is P=F1/A1. In the first worked example, 150 N on 0.0015 m² gives 100,000 Pa (computed), about the same as normal air pressure, added to the whole fluid.

Here is Pascal's principle written for two pistons connected by the same fluid, with every variable and its SI unit and the rearranged forms.

F1A1=F2A2
What each symbol means
SymbolQuantitySI unit
F1input forcenewton (N)
A1input piston areasquare meter (m²)
F2output forcenewton (N)
A2output piston areasquare meter (m²)

Rearranged to find another variable:

F2=F1A2A1F1=F2A1A2A2=A1F2F1A1=A2F1F2

Valid for: enclosed incompressible fluid, pistons at the same height.

Example 1 Output force of a garage lift

A mechanic pushes the small piston of a hydraulic lift with 150 N. The small piston has an area of 0.0015 m² and the large piston under the car has an area of 0.12 m². What upward force does the large piston produce?

  1. Given:
    • input force: F1=150 N
    • input piston area: A1=0.0015 m2
    • output piston area: A2=0.12 m2
  2. Formula: F2=F1A2A1
  3. Substitute: F1=150 N,A1=0.0015 m2,A2=0.12 m2
  4. Answer: F2=12,000 N

The large piston has 80 times the area of the small one, so it pushes with 80 times the force.

How Does a Hydraulic Lift Work?

A hydraulic lift is two cylinders joined by a pipe and filled with oil. A pump or lever pushes a small piston down, raising the oil pressure. That pressure spreads through the pipe to a wide piston under the platform, which rises and lifts the car.

The diagrams below show the two ends of the lift from the first worked example. On the small piston, a 150 N push is balanced by the oil pushing back. On the large piston, the oil pushes up with 12,000 N (computed), enough to hold a car of the same weight.

Oil is used rather than air because liquids hardly compress. If air were trapped in the lines, much of the input stroke would be wasted squeezing the air instead of moving the piston, which is why a car's brakes feel spongy when air gets into the brake fluid.

Example 2 How hard must you push to raise a car?

A loaded car weighs 14,000 N and rests on a hydraulic piston with an area of 0.2 m². The input piston has an area of 0.002 m². What input force holds the car up?

  1. Given:
    • output force: F2=14,000 N
    • input piston area: A1=0.002 m2
    • output piston area: A2=0.2 m2
  2. Formula: F1A1=F2A2
  3. Substitute: F2=14,000 N,A1=0.002 m2,A2=0.2 m2
  4. Answer: F1=140 N

A force this size is about what you need to hold up a 14 kg bag, so one person can support a whole car.

Free-body diagram of the small input piston, a 150 N push down balanced by a 150 N upward push from the oil
On the small 0.0015 m² piston, a 150 N push raises the oil pressure by 100,000 Pa.
Free-body diagram of a car on the large lift piston, its 12,000 N weight balanced by a 12,000 N push from the oil
The same pressure acting on the 0.12 m² piston pushes up with 12,000 N, enough to hold a car of that weight.

Does Pascal's Principle Create Energy?

No. A hydraulic system multiplies force, never energy. The volume of oil pushed out of the small cylinder must equal the volume that enters the large one, so A1d1=A2d2. If the large piston has 80 times the area, it rises only one eightieth as far as the small piston moves.

Multiply force by distance on each side and you get the same work, in agreement with conservation of energy. To raise a car 1 m with an 80 to 1 lift, the input piston must travel 80 m in total. Real lifts manage this with a pump that makes many short strokes, refilling the small cylinder from a reservoir each time.

In practice, friction in the seals and the flow of oil through valves turns a little of the input work into heat, so the output work is always slightly less than the input.

Who Discovered Pascal's Principle?

The French mathematician and physicist Blaise Pascal (1623 to 1662) worked out the principle around 1653. His treatise on the balance of liquids was published in 1663, the year after his death. Pascal also ran famous experiments on air pressure, building on the barometer work of Evangelista Torricelli.

Pascal pictured a sealed vessel with one small opening and one large opening, each closed by a piston, and argued that one person pressing the small piston could balance many people pressing the large one. A story often told about him involves a tall, thin tube fixed to a sealed barrel, where a modest amount of water in the tube was enough to burst the barrel. Whether or not he really did it, the story captures his point: pressure depends on height and area, not on the amount of water.

The SI unit of pressure, the pascal, is named in his honor. Working hydraulic presses based on his idea appeared in England in the late 1700s, and today hydraulics drive construction machines, aircraft controls and factory presses.

What Are Examples of Pascal's Principle in Everyday Life?

  • Car brakes. Your foot pushes a small piston in the master cylinder, and the pressure travels through thin lines to larger pistons at each wheel, which squeeze the brake pads.
  • Hydraulic jacks. A short handle pumped by hand raises a car or a house beam a little with each stroke.
  • Construction machines. Excavators and loaders move their arms with long hydraulic cylinders fed by a high-pressure pump.
  • Barber and dental chairs. A foot pedal pumps oil into a cylinder that raises the seat and the person in it.
  • Squeezing a tube of toothpaste. Pressing anywhere on the tube pushes paste out of the open end, because the pressure spreads through the whole tube.
  • Syringes and IV pumps. The pressure applied to the plunger reaches the needle tip and the fluid beyond it.

The table below compares a few hydraulic devices. The figures use typical piston sizes and show how the area ratio decides both the force gained and the extra distance the input must move.

Example 3 Sizing the piston of a log splitter

A small log splitter must push its wedge with 9,000 N. Its pump presses on an input piston of area 0.0012 m² with a force of 250 N. What area does the output piston need?

  1. Given:
    • input force: F1=250 N
    • output force: F2=9,000 N
    • input piston area: A1=0.0012 m2
  2. Formula: A2=A1F2F1
  3. Substitute: F1=250 N,F2=9,000 N,A1=0.0012 m2
  4. Answer: A2=0.0432 m2

Designers then add a margin, since real seals and valves lose a little force to friction.

How piston size sets the force gain of common hydraulic devices (200 N input force)
DeviceSmall piston diameter (cm)Large piston diameter (cm)Area ratio A2/A1Output force (N)Input travel per 1 cm of lift (cm)
Brake line, pedal to wheel256.251,2506.25
Floor jack2691,8009
Barber or dental chair2.51223.044,60823.04
Workshop press1.5126412,80064
Garage car lift33010020,000100
Source: Computed with F2 = F1 × (A2/A1) and A1 d1 = A2 d2, with area ratio = (diameter ratio)²; piston diameters are typical values; friction ignored · Retrieved October 2026
Excavator arm with shiny hydraulic cylinders digging soil, powered by Pascal's principle
Each hydraulic cylinder on an excavator arm turns high oil pressure into the large force needed to dig.

When Does Pascal's Principle Not Apply Exactly?

The principle assumes a fluid that is enclosed, at rest and nearly incompressible. Gases compress a lot, so a pressure change in a gas spreads out but also changes its volume, which makes pneumatic systems softer and less precise than hydraulic ones.

The simple formula also assumes the two pistons sit at the same height. If one is higher, the hydrostatic pressure of the fluid column between them adds or subtracts ρgh. In most machines that height correction is tiny compared with the pump pressure, so engineers can ignore it.

Finally, once the fluid is moving quickly, friction in pipes and the speed of the flow change the pressure from place to place. Flowing fluids are described by Bernoulli's principle instead.

How Can You Practice Pascal's Principle Problems?

Try the worked examples above with your own numbers, then move on to our pressure worksheets with full answer keys. The pressure calculator checks any force and area pair, and the hydraulic systems page shows how real pumps, valves and cylinders are put together. All the fluid equations sit together on the fluid formulas sheet.

Common Misconceptions

Myth: A hydraulic lift creates extra energy because it turns a small force into a large one.

Physics: It only multiplies force. The large piston moves a much shorter distance, so the work out never exceeds the work in.

Myth: The pressure is larger at the big piston because it pushes harder.

Physics: The pressure is the same at both pistons. The big piston pushes harder only because the same pressure acts on more area.

Myth: Pascal's principle works just as well with air in the system.

Physics: Air compresses, so much of the input motion is spent squeezing the gas. That is why air bubbles make hydraulic brakes feel soft.

Myth: The pressure fades as it travels down a long hydraulic hose.

Physics: In a fluid at rest the pressure change reaches every point in full. Losses appear only when the fluid flows fast through narrow pipes.

Key Facts

  • Pascal's principle states that pressure added to an enclosed fluid is passed on equally to every part of the fluid.
  • For two connected pistons, F1 / A1 = F2 / A2.
  • The output force grows in proportion to the area of the output piston.
  • A larger output force always comes with a shorter output distance, so no energy is gained.
  • Hydraulic systems use oil because liquids barely compress.
  • Blaise Pascal worked out the principle around 1653, and it was published in 1663.
  • Car brakes, jacks, excavators and lift chairs all rely on Pascal's principle.
Did you know? Because area grows with the square of diameter, doubling the width of a hydraulic piston quadruples the force it delivers for the same pressure.

Quick Quiz: How Well Do You Know Pascal's Principle?

6 questions. Tap an answer to check it.

  1. A hydraulic lift has an output piston with 50 times the area of its input piston. A 100 N push is applied to the input. What is the output force?

  2. In a hydraulic system, how does the pressure at the large piston compare with the pressure at the small piston?

  3. The large piston of a jack has 20 times the area of the small one. The small piston moves down 20 cm. How far does the large piston rise?

  4. Why do brakes feel spongy when air gets into the brake lines?

  5. A round output piston has 3 times the diameter of the input piston. What is the force multiplier?

  6. Which scientist gave his name to both this principle and the SI unit of pressure?

Frequently Asked Questions

What is Pascal's principle in simple terms?

Pascal's principle says that if you squeeze a fluid trapped in a closed container, the extra pressure spreads to every part of the fluid equally. Squeeze a sealed water bottle with holes in it and water sprays from all the holes. In machines, this lets a small push on a small piston make a big push on a large piston.

What is the formula for Pascal's law?

For two pistons connected by the same fluid, F1 / A1 = F2 / A2. F1 and A1 are the force and area at the input, and F2 and A2 are the force and area at the output. Rearranged, the output force is F2 = F1 × A2 / A1. Forces are in newtons, areas in square meters, and the shared pressure is in pascals.

What are three examples of Pascal's principle?

Three common examples are hydraulic car brakes, hydraulic jacks and the lifts in auto repair shops. In each one, a modest force on a small piston raises the pressure of an enclosed oil, and that pressure acts on a larger piston to produce a much bigger force. Excavator arms, dental chairs and squeezing a toothpaste tube work the same way.

How does Pascal's principle multiply force?

The pressure in the fluid is the same everywhere, and force equals pressure times area. So a piston with ten times the area of the input piston feels ten times the force. The catch is distance: the large piston moves only one tenth as far, because the same volume of fluid spreads over a wider cylinder.

Why is oil used in hydraulic systems instead of water?

Both liquids barely compress, so both obey Pascal's principle well. Oil is preferred because it lubricates seals and pistons, resists rust, does not boil as easily in hot brakes and stays liquid in freezing weather. Water would corrode metal parts and could freeze in winter. Special water-based fluids are still used where fire safety matters.

Who discovered Pascal's principle and when?

The French scientist Blaise Pascal established the principle around 1653. His writing on the balance of liquids was published in 1663, the year after he died. The SI unit of pressure, the pascal, is named after him. Inventors turned his idea into practical hydraulic presses more than a century later.

What is the difference between Pascal's principle and Archimedes' principle?

Pascal's principle is about how an added pressure spreads through an enclosed fluid, and it explains hydraulic machines. Archimedes' principle is about the upward buoyant force on an object in a fluid, equal to the weight of the fluid it pushes aside. Both come from the same rule that a fluid at rest pushes equally in all directions.

Does Pascal's principle apply to gases?

Partly. A pressure change does spread through a trapped gas, but the gas also compresses, so its volume changes and the output piston does not move as directly. That is why pneumatic tools feel springy. The principle works best with liquids, which keep almost the same volume under pressure.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.