Fluids · devices

Hydraulic Systems (Hydraulic Press and Lift)

A hydraulic system is a machine that uses a trapped liquid, usually oil, to pass a push from one piston to another and multiply the force. A small force on a narrow piston raises the pressure of the oil, and that same pressure acting on a wide piston produces a much larger force. Hydraulic presses, car lifts, jacks and brakes all work this way.

Silver sedan raised on a two-post hydraulic car lift in a clean workshop with steel columns and cylinder rods
A hydraulic car lift raises a whole car using oil pressure acting on wide pistons.

At a Glance

A hydraulic system multiplies force with an enclosed liquid. By Pascal's principle the pressure is the same on both pistons, so F1 / A1 = F2 / A2 and the output force is F2 = F1 × A2 / A1. The trade-off is distance: the large piston moves only A1 / A2 as far as the small one.

What it does
Multiplies force using a trapped liquid
Working fluid
Usually hydraulic oil (nearly incompressible)
Key formula
F1 / A1 = F2 / A2 (Pascal's principle)
Force gain
A2 / A1, or (D2 / D1)² for round pistons
Trade-off
Output piston moves a shorter distance
Common examples
Car lifts, jacks, presses, brakes, excavators
On this page
  1. What Is a Hydraulic System?
  2. How Does a Hydraulic System Work Step by Step?
  3. Why Does a Hydraulic Jack Have a Long Handle?
  4. What Is the Physics Behind Hydraulic Systems?
  5. Do Hydraulic Systems Create Energy?
  6. What Are the Main Types of Hydraulic Systems?
  7. Where Are Hydraulic Systems Used?
  8. Who Invented the Hydraulic Press?
  9. Key Facts
  10. Quiz
  11. FAQ

What Is a Hydraulic System?

A hydraulic system moves and multiplies force by pushing on a liquid sealed inside cylinders and hoses. The simplest version has two pistons of different sizes joined by a pipe full of oil. Push the small piston down and the large piston rises with a far bigger force.

The word hydraulic comes from the Greek for water, but modern systems use special oil. Oil barely compresses, lubricates the moving parts and does not rust the steel inside.

The same idea runs a garage car lift, the jack in a car trunk, the brakes on a car, the arms of an excavator and the giant presses that stamp out car body panels.

How Does a Hydraulic System Work Step by Step?

  1. You push the small piston. A modest force acts on a small area, which creates a high pressure in the oil.
  2. The pressure spreads everywhere. Because the oil is enclosed and nearly incompressible, the pressure rise reaches every part of the fluid equally.
  3. The large piston feels the same pressure. That pressure acts on a much bigger area, so the total force on the large piston is bigger in the same ratio.
  4. The load moves a short distance. The oil pushed out of the small cylinder spreads across the wide one, so the big piston rises only a little for each push.
  5. A valve holds or releases the load. A check valve stops oil flowing back, so the load stays up. Opening a release valve lets the oil return and lowers the load slowly.

In a hand jack, a pump repeats steps 1 to 4 many times. Each stroke draws oil from a reservoir and pushes it under the ram.

Why Does a Hydraulic Jack Have a Long Handle?

A bottle jack stacks two force multipliers. The handle is a lever that pivots near the pump piston, so a light push at the far end becomes a strong push on the piston. The hydraulic pistons then multiply that force again.

In the lever diagram, a 100 N push at the end of a 0.6 m handle drives the pump piston, 0.05 m from the pivot, with 1,200 N. The worked example shows what the oil does with that 1,200 N.

Multiplying the two gains gives the overall mechanical advantage of the jack, which is why one person can raise the corner of a car.

Class 2 lever: a 100 N push 0.6 m from the pivot drives a pump piston 0.05 m from the pivot with 1,200 N
The jack handle multiplies a 100 N push by 12 before the oil multiplies it again.

What Is the Physics Behind Hydraulic Systems?

Hydraulics rests on Pascal's principle: a pressure change applied to an enclosed fluid is transmitted undiminished to every part of the fluid. Pressure is force divided by area, so the same pressure on two pistons gives F1/A1=F2/A2.

Rearranging gives the output force F2=F1×A2/A1. The force gain is the ratio of the areas. For round pistons, area depends on the diameter squared, so doubling the diameter multiplies the force by four.

The pressures involved can be large. The extra oil pressure in a working jack or press is often many times atmospheric pressure, which is why hydraulic hoses are reinforced with steel braid. The readings on hydraulic gauges are gauge pressures, measured above the surrounding air.

Every hydraulic press and lift follows Pascal's principle for two pistons joined by the same liquid; here it is with each variable and its SI unit.

F1A1=F2A2
What each symbol means
SymbolQuantitySI unit
F1input forcenewton (N)
A1input piston areasquare meter (m²)
F2output forcenewton (N)
A2output piston areasquare meter (m²)

Rearranged to find another variable:

F2=F1A2A1F1=F2A1A2A2=A1F2F1A1=A2F1F2

Valid for: enclosed incompressible fluid, pistons at the same height.

Example 1 Force from a bottle jack

The pump piston of a bottle jack is 1.5 cm (0.015 m) across and the lifting ram is 5 cm (0.05 m) across. The handle pushes the pump piston with 1,200 N. What force does the ram push up with?

  1. Given:
    • input force: F1=1,200 N
    • D1: D1=0.015 m
    • D2: D2=0.05 m
  2. Formula: F2=F1(D2D1)2
  3. Substitute: F1=1,200 N,D1=0.015 m,D2=0.05 m
  4. Answer: F2=13,330 N

Area grows with the square of the diameter, so a ram just over three times wider gives about eleven times the force.

Free-body diagram of a jack ram with 13,333 N of oil pressure pushing up and a 13,333 N load pressing down
With a 1,200 N push on a 1.5 cm pump piston, the 5 cm ram can hold a load of about 13,333 N.

Do Hydraulic Systems Create Energy?

No. A hydraulic system multiplies force, not energy. The volume of oil leaving the small cylinder equals the volume entering the large one, so A1d1=A2d2. The big piston moves a shorter distance in exactly the ratio that its force is larger.

Multiply force by distance on each side and you get the same work: F1d1=F2d2. Real systems lose a little to friction in the seals and to heating of the oil, so the output work is always slightly less than the input.

The table shows the trade-off for different piston sizes. A bigger force gain always means more pumping for the same lift.

Force gain and distance trade-off for a 100 N push and a 10 cm input stroke
Diameter ratio D2/D1Area ratio A2/A1Output force (N)Output piston moves (cm)
1110010.00
244002.50
399001.11
5252,5000.40
1010010,0000.10
Source: Computed with F2 = F1 × (D2/D1)² and d2 = d1 × (D1/D2)² for an ideal, leak-free system · Retrieved October 2026

What Are the Main Types of Hydraulic Systems?

  • Hydraulic press: a fixed frame with a large ram that squeezes, bends, punches or shapes material. Small bench presses fit in a workshop; industrial presses can shape steel sheets.
  • Hydraulic lift: a ram or set of rams that raises a platform, used for car lifts, elevators in low buildings and loading docks.
  • Hydraulic jack: a portable pump and ram, either a bottle jack with a vertical ram or a floor jack with a long arm on wheels.
  • Hydraulic brakes: a master cylinder at the pedal feeds small cylinders at each wheel through thin pipes.
  • Powered hydraulics: an engine or electric motor drives a pump that sends oil to many cylinders, as in excavators, tractors, aircraft controls and garbage trucks.

Example 2 Clamping force of a disc brake

Pressing a brake pedal pushes the master cylinder piston, of area 0.0005 m², with a force of 900 N. Each caliper piston at the wheel has an area of 0.002 m². What force does one caliper piston press on the brake pad?

  1. Given:
    • input force: F1=900 N
    • input piston area: A1=5×10−4 m2
    • output piston area: A2=0.002 m2
  2. Formula: F2=F1A2A1
  3. Substitute: F1=900 N,A1=5×10−4 m2,A2=0.002 m2
  4. Answer: F2=3,600 N

Every caliper connected to the same fluid line gets this same boost, so all the wheels brake together.

Gray H-frame bench hydraulic press with a vertical ram pressing on a steel plate and a long pump handle at the side
A bench press uses a hand-pumped ram to squeeze parts with thousands of newtons of force.

Where Are Hydraulic Systems Used?

Hydraulics shows up wherever a machine needs a large, smooth and controllable force in a compact space. Construction machines use it to dig, lift and push. Car workshops use it to raise vehicles and press bearings in and out.

Aircraft use hydraulics to move flaps, landing gear and control surfaces. Factories use hydraulic presses to form metal, mold plastics and compress scrap. Even an office chair may have a small sealed cylinder, though many of those use compressed gas rather than oil.

Hydraulics is less suited to very fast or very precise light movements, where electric motors usually win, and it needs care to prevent leaks.

Example 3 Input force for a heavy press

A workshop press must squeeze a metal part with 50,000 N. Its output piston has an area of 0.03 m² and its pump piston has an area of 0.0006 m². What force must the pump apply?

  1. Given:
    • output force: F2=50,000 N
    • input piston area: A1=6×10−4 m2
    • output piston area: A2=0.03 m2
  2. Formula: F1=F2A1A2
  3. Substitute: F2=50,000 N,A1=6×10−4 m2,A2=0.03 m2
  4. Answer: F1=1,000 N

The pump piston must travel 50 times farther than the output piston, which is why presses pump many short strokes.

Who Invented the Hydraulic Press?

The principle came first. In the mid-1600s the French scientist Blaise Pascal described how pressure spreads through an enclosed liquid and pointed out that a small piston could balance a much larger one.

Turning that idea into a working machine was hard, because the seals leaked under high pressure. The English inventor Joseph Bramah patented a practical hydraulic press in 1795, helped by a leather seal, developed in his workshop, that tightened as the pressure rose. Hydraulic cranes and lifts spread through docks and factories during the 1800s, and hydraulic brakes began appearing on cars in the early 1900s.

Key Facts

  • A hydraulic system multiplies force by pressing on a trapped, nearly incompressible liquid.
  • Pascal's principle makes the pressure equal on both pistons, so F1 / A1 = F2 / A2.
  • The force gain equals the area ratio, which is the diameter ratio squared for round pistons.
  • The larger piston moves a shorter distance, so the work in and out stay equal at best.
  • Hydraulic oil is used because it barely compresses, lubricates and resists rust.
  • Check valves hold a load up, and release valves let it down slowly.
  • Car brakes, jacks, lifts, presses and excavators all rely on hydraulics.
Did you know? A car's brake pedal and the brakes at all four wheels are linked only by thin tubes of fluid, so the push from one foot is shared out and multiplied at every wheel at the same instant.

Quick Quiz: How Well Do You Know Hydraulic Systems (Hydraulic Press and Lift)?

6 questions. Tap an answer to check it.

  1. Which principle explains how a hydraulic press works?

  2. A hydraulic lift has an output piston with 20 times the area of the input piston. A 150 N push gives what output force?

  3. If the output piston diameter is three times the input piston diameter, the force gain is

  4. What is the trade-off for the extra force in a hydraulic system?

  5. Why does air in brake lines make the pedal feel spongy?

  6. Who patented a practical hydraulic press in 1795?

Frequently Asked Questions

How does a hydraulic system work?

A hydraulic system uses a liquid sealed inside cylinders to carry a push from one piston to another. Pushing a small piston raises the pressure of the liquid, and that pressure spreads evenly to a larger piston. Because the larger piston has more area, the same pressure gives it a bigger force, so a small input lifts a heavy load.

How does a hydraulic press multiply force?

It uses two pistons of different areas joined by the same oil. The pressure is equal on both, so the force on each piston is proportional to its area. If the output piston has 50 times the area of the input piston, it pushes with 50 times the force, while moving only one fiftieth as far.

What is the formula for a hydraulic lift?

The formula is F1 / A1 = F2 / A2, from Pascal's principle. Rearranged, the output force is F2 = F1 × A2 / A1. For round pistons you can use diameters instead: F2 = F1 × (D2 / D1)². The distances moved follow the opposite ratio, so the larger piston travels less.

Why is oil used instead of water in hydraulic systems?

Oil barely compresses, just like water, but it also lubricates the pistons and seals, protects steel parts from rust, works over a wide temperature range and does not boil away easily. Water would corrode the cylinders and freeze in cold weather. Some special systems do use water-based fluids where fire safety matters more.

Do hydraulic systems break the law of conservation of energy?

No. They trade distance for force. The output piston pushes harder but moves a shorter distance, so the work out, force times distance, is never more than the work in. Friction in the seals and heating of the oil mean the output work is always a little less than the input in real machines.

What happens if there is air in a hydraulic system?

Air compresses easily, so some of your push is wasted squeezing the bubbles instead of moving the piston. In car brakes this makes the pedal feel soft or spongy and can reduce braking force. Mechanics remove trapped air by bleeding the system, letting fluid flow out of a valve until no bubbles remain.

What is the difference between hydraulic and pneumatic systems?

Hydraulic systems use a liquid, usually oil, while pneumatic systems use compressed air. Liquids barely compress, so hydraulics gives large, steady and precise forces. Air compresses, so pneumatic systems are springier and better for fast, lighter jobs such as air tools and door closers. Both follow the same rule that pressure times area equals force.

How does a hydraulic jack lift a car?

A long handle works as a lever to push a small pump piston with a large force. Each stroke forces oil past a check valve into the cylinder under a wide ram, which rises a little with a much larger force. After many strokes the car is lifted. Opening a release valve lets the oil flow back and lowers the car gently.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.