The top speed of a fall

Terminal Velocity

Terminal velocity is the constant speed a falling object reaches when the upward drag from the air grows to equal its weight, so the net force becomes zero and it stops speeding up. A skydiver falling belly-down reaches roughly 50 to 55 m/s, while a raindrop settles at only a few meters per second. The value depends on mass, shape, size and the density of the fluid.

Skydiver falling belly-down with arms spread high above fields, falling at a steady terminal velocity
Spread out belly-down, a skydiver soon falls at a steady speed as air resistance balances weight.

At a Glance

Terminal velocity is the steady speed of a falling object when air resistance balances its weight, so it no longer accelerates. For drag that grows with speed squared, v_t = sqrt(2 m g / (ρ C A)), where ρ is the fluid density, C the drag coefficient and A the cross-sectional area. Heavier, more streamlined objects have higher terminal velocities.

Symbol
vt
SI unit
meter per second (m/s)
Formula
vt = √(2mg / ρCA)
Scalar or vector
Usually quoted as a speed; the velocity points downward
Condition
Drag force equals weight, net force is zero
Depends on
Mass, drag coefficient, area, fluid density, g
On this page
  1. What Is Terminal Velocity?
  2. Terminal Velocity Explained Simply
  3. How Does an Object Reach Terminal Velocity?
  4. What Forces Act on a Falling Object?
  5. What Is the Formula for Terminal Velocity?
  6. What Affects Terminal Velocity?
  7. How Does a Parachute Reduce Terminal Velocity?
  8. Why Don't Raindrops Hurt?
  9. Is There Terminal Velocity in a Vacuum?
  10. Practice Terminal Velocity Problems
  11. Common Misconceptions
  12. Key Facts
  13. Quiz
  14. FAQ

What Is Terminal Velocity?

Terminal velocity is the fastest speed an object reaches while falling through air or another fluid. It happens when the push of the air on the falling object, called drag or air resistance, becomes as strong as the object's weight. At that point the forces are balanced, and the object keeps falling at a steady speed instead of going faster and faster.

The word terminal means final or end. It does not mean deadly. Plenty of objects reach terminal velocity gently: a dandelion seed, a snowflake or a falling leaf all reach their top speed within a fraction of a second and drift down slowly.

Terminal velocity is measured in meters per second. Because it is reached at a steady speed in a fixed direction, physicists often quote it simply as a speed, even though the velocity itself points down.

Terminal Velocity Explained Simply

Stick your hand out of a moving car's window. At low speed you barely feel the air, but at highway speed the wind shoves your hand back hard. Air pushes harder on things that move through it faster.

A falling object meets the same effect. At first it falls slowly, the air barely pushes, and gravity wins easily, so it speeds up. As it speeds up, the air pushes harder. Eventually the air pushes up just as hard as gravity pulls down, and the object stops gaining speed.

From then on it falls at the same speed until it lands or something changes, such as a parachute opening. That steady top speed is its terminal velocity.

How Does an Object Reach Terminal Velocity?

Follow a skydiver after stepping out of a plane. At the very first instant the speed is low, drag is close to zero, and the only real force is weight. The skydiver accelerates downward at almost 9.8 m/s², just like in free fall.

As speed grows, drag grows with roughly the square of the speed, so doubling the speed makes the drag about four times larger. The net force, weight minus drag, gets smaller, and so does the acceleration. The speed keeps rising, but more and more slowly.

Finally drag equals weight, the net force is zero, and the acceleration is zero. By Newton's first law, the skydiver now falls at constant velocity. In practice, a skydiver gets close to terminal speed after roughly 10 to 15 seconds and a few hundred meters of falling.

What Forces Act on a Falling Object?

Ignoring wind, two forces act on an object falling through still air. Its weight pulls down with a constant size, mg. Drag pushes up, against the motion, and its size depends on speed. A third force, buoyancy, also pushes up, but for dense objects in air it is tiny and usually left out.

The two diagrams below show the same 80 kg skydiver at two moments. Early in the fall, drag is smaller than weight, so a net force points down and the skydiver speeds up. At terminal velocity, the two arrows are equal in length and the forces are balanced.

Free-body diagram of an 80 kg skydiver early in the fall, 784 N weight and 300 N drag leaving a 484 N net force downward
Early in the fall, drag is smaller than weight, so a net force points down and the skydiver speeds up.
Free-body diagram of the same 80 kg skydiver at terminal velocity, with 784 N of drag balancing 784 N of weight
At terminal velocity, drag has grown to equal weight, the net force is zero and the speed stays constant.

What Is the Formula for Terminal Velocity?

For most everyday objects moving through air, the drag force is FD=12CρAv2, where C is the drag coefficient, ρ is the air density and A is the area facing the flow. You can explore that relation on our drag force page.

At terminal velocity, drag equals weight: 12CρAvt2=mg. Solving for the speed gives the formula below. It says that a heavier object, or one with a smaller or more streamlined profile, falls faster at the end. Thin air at high altitude also raises the terminal speed, since ρ is smaller there.

The formula assumes drag grows with speed squared, which fits objects the size of a ball or larger. Very small or very slow objects follow a different rule, covered further down.

Setting the drag force equal to the weight and solving for speed gives this formula. Here it is with each symbol and its SI unit.

vt=2mgρCA
What each symbol means
SymbolQuantitySI unit
vtterminal speedmeter per second (m/s)
mmass of falling objectkilogram (kg)
gacceleration due to gravity (9.80 m/s² (standard 9.80665 m/s²))meter per second squared (m/s²)
ρdensity of the fluid (air ≈ 1.2 kg/m³)kilogram per cubic meter (kg/m³)
Cdrag coefficientdimensionless (1)
Across-sectional areasquare meter (m²)

Rearranged to find another variable:

m=ρCAvt22gA=2mgρCvt2C=2mgρAvt2

Valid for: drag force ∝ v² balances weight; buoyancy neglected.

Example 1 A skydiver falling belly-down

An 80 kg skydiver with gear falls in a spread, belly-down position. Take the air density as 1.2 kg/m³, the drag coefficient as 1.0 and the area facing the air as 0.7 m². What is the terminal speed? Use g = 9.8 m/s².

  1. Given:
    • mass of falling object: m=80 kg
    • acceleration due to gravity: g=9.8 m/s2
    • density of the fluid (air ≈ 1.2 kg/m³): ρ=1.2 kg/m3
    • drag coefficient: C=1
    • cross-sectional area: A=0.7 m2
  2. Formula: vt=2mgρCA
  3. Substitute: m=80 kg,g=9.8 m/s2,ρ=1.2 kg/m3,C=1,A=0.7 m2
  4. Answer: vt=43.2 m/s (155.5 km/h, 96.65 mph)

Real skydivers in this position fall a little faster than this simple estimate, because a tucked body has a smaller effective area than a flat plate.

What Affects Terminal Velocity?

Each quantity in the formula changes the answer in a predictable way:

  • Mass. More mass means more weight to balance, so the object must fall faster before drag catches up. Terminal speed grows with the square root of mass.
  • Area. A larger area facing the air catches more drag. Spreading out lowers terminal speed; diving head-first raises it.
  • Shape. A streamlined shape has a low drag coefficient, so it slips through air and falls faster than a blunt shape of the same size.
  • Fluid density. Water is about 800 times denser than air near sea level, so objects reach much lower terminal speeds when sinking through water.
  • Gravity. On a world with weaker gravity, the same object would reach a lower terminal speed in the same atmosphere.

The table compares estimates for several objects, computed with the formula and typical sizes and drag coefficients.

Estimated terminal speeds of falling objects in air at sea level
ObjectMass (kg)Drag coefficientArea (m²)Terminal speed (m/s)Terminal speed (mph)
Raindrop, 2 mm across4.19 × 10⁻⁶0.53.14 × 10⁻⁶6.615
Ping-pong ball0.00270.50.001268.419
Hailstone, 2 cm across0.00380.50.0003120.045
Baseball0.1450.350.004240.290
Skydiver, belly-down801.00.743.297
Skydiver, head-down800.70.18101.8228
Jumper under open parachute901.5256.314
Source: Computed with v_t = √(2mg / ρCA), ρ = 1.2 kg/m³, g = 9.8 m/s²; masses, areas and drag coefficients are typical values · Retrieved October 2026

How Does a Parachute Reduce Terminal Velocity?

A parachute works by making the area A huge and the shape very blunt. When the canopy opens, the drag force jumps far above the jumper's weight. For a moment the net force points up, so the jumper slows down sharply even though they are still moving downward.

As the speed drops, drag shrinks again until it once more matches the weight. The jumper settles at a new, much lower terminal speed of around 5 m/s, slow enough to land on their feet. The worked example below shows how designers pick the canopy size for a target landing speed.

Example 2 Sizing a parachute for a gentle landing

A 90 kg jumper with gear wants a terminal speed of 5 m/s under an open canopy. If the canopy's drag coefficient is 1.5 and the air density is 1.2 kg/m³, what area must the canopy present to the air? Use g = 9.8 m/s².

  1. Given:
    • mass of falling object: m=90 kg
    • acceleration due to gravity: g=9.8 m/s2
    • density of the fluid (air ≈ 1.2 kg/m³): ρ=1.2 kg/m3
    • drag coefficient: C=1.5
    • terminal speed: vt=5 m/s
  2. Formula: A=2mgρCvt2
  3. Substitute: m=90 kg,g=9.8 m/s2,ρ=1.2 kg/m3,C=1.5,vt=5 m/s
  4. Answer: A=39.2 m2

That is roughly the floor area of a two-car garage, which is why round canopies built for slow landings are so large.

Jumper drifting down under a large round parachute canopy, which lowers the terminal velocity to a safe landing speed
A wide canopy multiplies the drag, so the jumper settles at a much lower terminal speed.

Why Don't Raindrops Hurt?

Rain falls from clouds a kilometer or more above the ground. Without air, a drop from that height would arrive at well over 100 m/s. Air resistance changes everything: a typical drop gets close to its terminal speed within about ten meters of falling and then drifts down at a few meters per second.

Small objects have a large surface area compared with their mass, so drag catches up with their weight quickly. This is why dust hangs in the air, why fog droplets float, and why an insect can survive a fall that would injure a person. For the tiniest particles, drag grows in direct proportion to speed rather than its square, and their terminal speeds become tiny.

Example 3 How fast does a raindrop land?

A raindrop 2 mm across has a mass of about 4.19 × 10⁻⁶ kg and a cross-sectional area of about 3.14 × 10⁻⁶ m². Treat it as a sphere with a drag coefficient of 0.5 falling through air of density 1.2 kg/m³. Estimate its terminal speed. Use g = 9.8 m/s².

  1. Given:
    • mass of falling object: m=4.19×10−6 kg
    • acceleration due to gravity: g=9.8 m/s2
    • density of the fluid (air ≈ 1.2 kg/m³): ρ=1.2 kg/m3
    • drag coefficient: C=0.5
    • cross-sectional area: A=3.14×10−6 m2
  2. Formula: vt=2mgρCA
  3. Substitute: m=4.19×10−6 kg,g=9.8 m/s2,ρ=1.2 kg/m3,C=0.5,A=3.14×10−6 m2
  4. Answer: vt=6.602 m/s (23.77 km/h, 14.77 mph)

Rain at this speed taps your umbrella instead of hurting you, all because air resistance caps the speed of each drop.

Is There Terminal Velocity in a Vacuum?

No. Terminal velocity needs a fluid to push back. In a vacuum there is no drag, so a falling object keeps accelerating at g until it hits something. On the Moon, which has almost no atmosphere, a hammer and a feather dropped together land at the same moment.

That result connects to an old question: why do objects fall at the same rate? Without air, every object falls with the same acceleration. Air resistance is the only reason a sheet of paper loses the race against a stone here on Earth. Galileo Galilei reasoned this out centuries before anyone could test it in a vacuum chamber.

Practice Terminal Velocity Problems

Terminal velocity ties together forces and motion, so practice in both helps. Our free fall worksheets include printable sets with answer keys, and the free fall calculator shows what a fall would look like with no air at all, a useful comparison. The force formulas sheet lists drag and terminal velocity together. To keep speed and velocity straight, see speed vs velocity, then try the quiz.

Common Misconceptions

Myth: At terminal velocity there are no forces acting on the object.

Physics: Weight and drag still act, but they are equal and opposite, so the net force is zero.

Myth: A falling object stops moving when it reaches terminal velocity.

Physics: It keeps falling at a constant speed. Only its acceleration drops to zero.

Myth: Heavier objects always fall faster.

Physics: In a vacuum all objects fall together. In air a heavier object of the same size and shape does reach a higher terminal speed, but shape and area matter as much as mass.

Myth: When a parachute opens, the jumper shoots upward.

Physics: The jumper keeps moving down but slows sharply. It only looks like an upward jerk from a camera that keeps falling fast.

Key Facts

  • Terminal velocity is the constant speed a falling object reaches when drag equals its weight.
  • At terminal velocity the net force is zero, so the object no longer accelerates.
  • For drag that grows with speed squared, v_t = √(2mg / ρCA).
  • Heavier and more streamlined objects have higher terminal velocities.
  • A skydiver falling belly-down reaches roughly 50 to 55 m/s, while an open parachute brings that down to about 5 m/s.
  • Raindrops reach only a few meters per second, which is why rain does not injure people.
  • There is no terminal velocity in a vacuum, because there is no drag.
Did you know? A cat that falls from a great height reaches a terminal speed of roughly 27 m/s, and some cats instinctively spread their legs like a flying squirrel to raise their drag and slow down.

Quick Quiz: How Well Do You Know Terminal Velocity?

6 questions. Tap an answer to check it.

  1. What is true about the forces on an object falling at terminal velocity?

  2. What is the acceleration of an object at terminal velocity?

  3. A skydiver changes from a spread position to a head-down dive. What happens to her terminal velocity?

  4. Why is there no terminal velocity on the airless Moon?

  5. In the formula v_t = √(2mg / ρCA), what does ρ stand for?

  6. If the mass of an object is quadrupled while its size and shape stay the same, its terminal velocity:

Frequently Asked Questions

What is terminal velocity in simple terms?

Terminal velocity is the top speed something reaches while falling through air. As it falls faster, the air pushes back harder. When that push equals the pull of gravity, the object stops speeding up and falls at a steady speed. A raindrop, a skydiver and a feather all have a terminal velocity, though their values are very different.

What is the terminal velocity of a human?

A person falling belly-down with arms and legs spread reaches roughly 50 to 55 m/s, about 110 to 125 mph, in air near sea level. Diving head-first with the body streamlined cuts the drag a lot and raises the speed to around 80 to 90 m/s or more. Higher up, where the air is thinner, the speed is greater still.

What is the formula for terminal velocity?

For objects large enough that drag grows with speed squared, terminal velocity is v_t = √(2mg / ρCA). Here m is mass, g is the acceleration due to gravity, ρ is the fluid density, C is the drag coefficient and A is the cross-sectional area. It comes from setting the drag force equal to the weight and solving for speed.

How long does it take to reach terminal velocity?

It depends on the object. A raindrop or a feather gets close within a fraction of a second. A skydiver gets close to terminal speed after roughly 10 to 15 seconds, having fallen a few hundred meters. Strictly speaking, the speed approaches its terminal value gradually and never quite reaches it, but it gets within a percent or so fairly quickly.

Does a heavier object have a higher terminal velocity?

If two objects have the same size and shape, yes. The heavier one has more weight to balance, so it must fall faster before drag matches it. A bowling ball and a plastic ball of the same size show this clearly. But shape and area matter just as much, which is why a heavy parachutist can still land slowly.

Is terminal velocity the same as maximum velocity?

For a falling object starting from rest, terminal velocity is the highest speed it approaches. But an object can briefly go faster than its terminal velocity, for example a skydiver who opens a parachute while still moving at full speed. Drag then exceeds weight and slows the jumper down toward the new, lower terminal speed.

Why is acceleration zero at terminal velocity?

Acceleration depends on the net force, as Newton's second law states. At terminal velocity the upward drag exactly equals the downward weight, so the net force is zero. With zero net force there is zero acceleration, and the object keeps moving at whatever speed it has. That steady speed is the terminal velocity.

Do objects have a terminal velocity in water?

Yes, and it is usually much lower than in air. Water is far denser than air, so drag builds up quickly, and buoyancy also pushes up noticeably. A pebble sinking in a pond reaches a steady speed within a few centimeters. Objects less dense than water never sink at all, because buoyancy alone outweighs gravity.

Sources

Constants come from NIST CODATA 2022 (public domain) and unit definitions from the BIPM SI Brochure (CC BY 4.0). Text, diagrams and illustrations are original work by Physics Tribune.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.