
At a Glance
The Venturi effect is the lower pressure found in the narrow part (throat) of a pipe, where the fluid flows faster. Continuity gives the speed, A1 v1 = A2 v2, and Bernoulli's equation gives the pressure drop, P1 − P2 = 1/2 ρ (v2^2 − v1^2). The narrower the throat, the faster the flow and the larger the pressure drop.
- What happens
- Pressure falls where a pipe narrows and the fluid speeds up
- Cause
- Mass conservation (continuity) plus energy conservation (Bernoulli)
- Speed in the throat
- v₂ = A₁v₁ / A₂
- Pressure drop
- ΔP = ½ρ(v₂² − v₁²)
- Named after
- Giovanni Battista Venturi, Italian physicist, 1790s
- Used in
- Flow meters, carburetors, aspirators, sprayers, gas burners
On this page
- What Is the Venturi Effect?
- The Venturi Effect Explained Simply
- What Causes the Venturi Effect?
- How Does the Venturi Effect Happen Step by Step?
- How Big Is the Pressure Drop?
- How Does a Venturi Meter Measure Flow?
- Where Do You See the Venturi Effect?
- How Is It Related to Other Flow Effects?
- Who Discovered the Venturi Effect?
- Common Misconceptions
- Key Facts
- Quiz
- FAQ
What Is the Venturi Effect?
The Venturi effect is a pressure drop caused by a fluid speeding up through a constriction. Picture water flowing through a pipe that pinches down to a narrow neck, called the throat, and then widens again. In the throat the water moves faster and pushes less hard on the walls than it does in the wide parts on either side.
The effect works for liquids and gases alike, as long as the flow is smooth and the fluid is not squeezed much. Air rushing through the narrow neck of a carburetor, water racing through a garden hose nozzle and gas jets in a stove burner all show it. The pressure recovers most of its value once the pipe widens again downstream.
It is a special case of Bernoulli's principle, applied to a closed pipe with a change in width. What makes it useful is that the pressure drop is predictable, so engineers can measure it, use it as a gentle suction source or turn it into a reading of flow speed.
The Venturi Effect Explained Simply
Imagine a crowd walking through a wide hallway that narrows to a single doorway. To get the same number of people through each second, everyone has to hurry up at the door. Fluid in a pipe behaves the same way: the same amount must pass every point each second, so it speeds up where the space is tight.
Speeding something up takes a push. The only thing that can push a fluid forward inside a pipe is a pressure difference, higher pressure behind and lower pressure ahead. So the fluid entering the throat must have higher pressure behind it than in front of it. That is why the pressure in the throat ends up lower.
Once the pipe widens, the fluid slows back down, and the pressure climbs again. A real pipe loses a little to friction, so the final pressure is slightly below the starting value.
What Causes the Venturi Effect?
Two conservation laws work together. The first is conservation of mass. For a liquid that cannot be compressed, the volume flow rate is the same at every cross-section, which is the continuity equation:
The second is conservation of energy, written for a moving fluid as Bernoulli's equation. In a horizontal pipe the height terms are equal, so pressure and kinetic energy per unit volume must add to the same total at both points:
Rearranging gives the size of the drop,
The first half of the story is the continuity equation, which sets how much faster the fluid must move in the throat.
| Symbol | Quantity | SI unit |
|---|---|---|
| cross-sectional area at point 1 | square meter (m²) | |
| flow speed at point 1 | meter per second (m/s) | |
| cross-sectional area at point 2 | square meter (m²) | |
| flow speed at point 2 | meter per second (m/s) |
Rearranged to find another variable:
Valid for: incompressible fluid, steady flow.
Example 1 Speed in the throat of a water line
Water moves at 1.2 m/s through a pipe section with a cross-sectional area of 0.0020 m². The pipe then narrows to a throat of 0.0005 m². How fast does the water move in the throat?
- Given:
- cross-sectional area at point 1:
- flow speed at point 1:
- cross-sectional area at point 2:
- cross-sectional area at point 1:
- Formula:
- Substitute:
- Answer:
(17.28 km/h, 10.74 mph)
The throat has one quarter of the area, so the water has to move four times faster to keep the flow rate the same.
How Does the Venturi Effect Happen Step by Step?
- Steady flow arrives. Fluid moves through the wide inlet at a steady speed and pressure.
- The pipe narrows. The converging section squeezes the same flow into less area.
- The fluid accelerates. Higher pressure upstream pushes each parcel of fluid forward, so it gains speed as it moves into the narrowing cone.
- Pressure bottoms out in the throat. The fluid is fastest at the narrowest point, and the pressure is lowest there.
- The pipe widens. In the diverging section the fluid slows, and the pressure rises back toward its upstream value.
- A small loss remains. Friction with the walls and some swirling turn a little energy into heat, so the outlet pressure is slightly lower than the inlet pressure.
The diagram shows this with two thin tubes standing on the pipe. The water column above the throat is shorter, which is a direct picture of the lower pressure there.
Example 2 How much pressure is lost in the throat?
In the same horizontal pipe, the water pressure in the wide section is 150,000 Pa, the speed there is 1.2 m/s and the speed in the throat is 4.8 m/s. Using a water density of 1,000 kg/m³, what is the pressure in the throat?
- Given:
- pressure at point 1:
- fluid density:
- flow speed at point 1:
- flow speed at point 2:
- pressure at point 1:
- Formula:
- Substitute:
- Answer:
The pipe is horizontal, so the height terms cancel and only the speed change lowers the pressure.

How Big Is the Pressure Drop?
The drop depends on three things: the density of the fluid, the speed going in and the ratio of the inlet area to the throat area. Dense water gives large drops even at walking-pace speeds, while air needs much higher speeds to produce the same effect.
The table compares water entering at 1 m/s with air entering at 10 m/s. Doubling the area ratio from 2 to 4 multiplies the pressure drop by five, not two, because the throat speed is squared. When the pressure in the throat would fall below the vapor pressure of a liquid, small bubbles form and collapse, a damaging process called cavitation that pump and valve designers work hard to avoid.
| Area ratio A₁/A₂ | Water, inlet 1 m/s: ΔP (Pa) | Same drop as water column (cm) | Air, inlet 10 m/s: ΔP (Pa) |
|---|---|---|---|
| 1.5 | 625 | 6.4 | 75 |
| 2 | 1,500 | 15.3 | 180 |
| 3 | 4,000 | 40.8 | 480 |
| 4 | 7,500 | 76.5 | 900 |
| 5 | 12,000 | 122.3 | 1,440 |
| Source: Computed with ΔP = ½ρ(v₂² − v₁²) and v₂ = (A₁/A₂)v₁; densities 1,000 kg/m³ for water and 1.2 kg/m³ for air (typical values), g = 9.81 m/s²; ideal flow without friction · Retrieved October 2026 | |||
How Does a Venturi Meter Measure Flow?
A Venturi meter is a short section of pipe with a smooth cone narrowing to a throat and a longer cone opening back out. Pressure taps at the inlet and at the throat feed a gauge, or two columns of liquid, that read the pressure difference.
Since the area ratio is fixed by the shape, a single measured pressure difference is enough to calculate the inlet speed, and speed times area gives the volume flow rate. The meter has no moving parts and loses very little pressure overall, which is why water utilities and chemical plants still use it. The gentle exit cone is the secret: it lets the fluid slow down without breaking into eddies.
Example 3 Reading flow speed from a Venturi meter
A Venturi meter on a water main has an inlet area of 0.0020 m² and a throat area of 0.0005 m². The pressure gauges show a difference of 10,800 Pa between the inlet and the throat. With a water density of 1,000 kg/m³, how fast is the water moving at the inlet?
- Given:
- inlet area:
- throat area:
- pressure difference between inlet and throat:
- fluid density:
- inlet area:
- Formula:
- Substitute:
- Answer:
(4.32 km/h, 2.684 mph)
The meter works backward from the first two examples: a measured pressure difference gives the speed, and speed times area gives the flow rate.
Where Do You See the Venturi Effect?
- Carburetors. In older engines, air rushing through a narrow throat creates low pressure that draws fuel out of a small jet and mixes it into the airstream.
- Aspirators and lab vacuum pumps. Tap water forced through a narrow nozzle creates enough suction to pull air from a flask attached to a side arm.
- Paint and perfume sprayers. A fast jet of air across the top of a thin tube lowers the pressure there, lifting liquid up the tube and breaking it into droplets.
- Gas burners. The fuel jet in a stove or a lab burner pulls in surrounding air through side holes so the gas burns cleanly.
- Medical oxygen masks. Some masks use a Venturi port to mix a set fraction of room air with pure oxygen.
- Wind between buildings. Air squeezed through a gap between tall buildings speeds up, which is why some city corners feel much windier than open streets.

Who Discovered the Venturi Effect?
The effect is named after the Italian physicist Giovanni Battista Venturi, who studied how water flows through tubes with narrow sections in the 1790s. The energy reasoning behind it goes back further, to the work of Daniel Bernoulli on moving fluids in the 1730s. In the 1880s the American engineer Clemens Herschel built the first practical Venturi flow meter for measuring water in large pipes and gave it Venturi's name.
Common Misconceptions
Myth: The fluid speeds up in the throat because it is being squeezed to a higher pressure.
Physics: The opposite is true. Pressure is lowest in the throat, and the higher pressure upstream is what pushes the fluid faster.
Myth: Narrowing a pipe reduces the amount of fluid that flows through it.
Physics: In steady flow the volume per second is the same everywhere along the pipe. The narrow part carries the same flow by moving it faster.
Myth: All the pressure lost in the throat is gone for good.
Physics: Most of it comes back as the fluid slows in the widening section. Only a small part is lost to friction and turbulence.
Key Facts
- The Venturi effect is the pressure drop in the narrow throat of a pipe, where the fluid moves fastest.
- Continuity, A₁v₁ = A₂v₂, sets the throat speed, and Bernoulli's equation sets the pressure drop.
- The ideal pressure drop is ΔP = ½ρ(v₂² − v₁²), so it grows with the square of the throat speed.
- Halving the throat area doubles the throat speed and roughly quadruples the pressure drop.
- A Venturi meter turns a measured pressure difference into a flow speed and flow rate, with no moving parts.
- Carburetors, aspirators, sprayers and gas burners use the low pressure in the throat to pull in a second fluid.
- The effect is named after Giovanni Battista Venturi, who studied flow through narrowing tubes in the 1790s.
Quick Quiz: How Well Do You Know Venturi Effect?
6 questions. Tap an answer to check it.
Where is the pressure lowest in a Venturi tube?
The fluid is fastest in the throat, so the pressure there is lowest.
A pipe narrows to one third of its area. How does the flow speed change?
Continuity, A₁v₁ = A₂v₂, means speed rises by the same factor the area shrinks.
Which two ideas together explain the Venturi effect?
Continuity gives the speed increase, and Bernoulli's equation links that speed to a pressure drop.
Why does a Venturi meter have no moving parts?
The fixed area ratio turns one measured pressure difference into a flow speed.
What happens to the pressure drop if the throat speed doubles while the inlet speed is very small?
The drop depends on the square of the throat speed.
Which device uses the Venturi effect to pull in a second fluid?
Fast air in the carburetor throat lowers the pressure and draws fuel out of a jet.
Frequently Asked Questions
What is the Venturi effect in simple terms?
It is the drop in pressure that happens when a fluid squeezes through a narrow part of a pipe and speeds up. The same amount of fluid has to get through every second, so it moves faster in the tight spot. Faster flow inside a pipe always comes with lower pressure, and that low-pressure zone can be measured or used to suck in another fluid.
What is the difference between the Venturi effect and Bernoulli's principle?
Bernoulli's principle is the general rule that faster flow along a streamline goes with lower pressure. The Venturi effect is one specific case of it, a fluid flowing through a pipe that narrows and widens again. Bernoulli explains why the pressure drops, and the continuity equation tells you how much faster the fluid moves in the narrow throat.
Why does pressure decrease when velocity increases?
A fluid can only speed up if something pushes it forward, and inside a pipe that push comes from a pressure difference. Fluid entering a narrowing has higher pressure behind it than ahead of it, so it accelerates into the lower-pressure throat. In energy terms, the fluid gains kinetic energy per unit volume and must give up the same amount of pressure energy.
How do you calculate the Venturi effect?
First find the speed in the throat with the continuity equation, v2 = A1 v1 / A2. Then use Bernoulli's equation for a horizontal pipe to get the pressure drop, P1 − P2 = 1/2 ρ (v2^2 − v1^2), where ρ is the fluid density. Work in SI units, square meters, meters per second and kilograms per cubic meter, so the drop comes out in pascals.
Does the Venturi effect work with air?
Yes. Air behaves almost like an incompressible fluid at speeds well below the speed of sound, so the same equations apply. Because air is about 800 times less dense than water, it needs much higher speeds to give the same pressure drop. That is why carburetors, sprayers and burners rely on fast-moving air or gas jets.
What is a Venturi tube used for?
A Venturi tube is most often used to measure flow rate in water mains, fuel lines and industrial pipes. Pressure readings at the inlet and the throat give the speed and the flow rate. The same shape is used as a suction device in aspirators, as a fuel mixer in carburetors and as an air mixer in gas burners and some oxygen masks.
What is cavitation in a Venturi?
If the throat pressure in a liquid drops below the liquid's vapor pressure, the liquid starts to boil locally even at room temperature. Tiny vapor bubbles form in the throat and then collapse violently when the pressure rises downstream. The collapse can pit metal surfaces and make noise, so designers limit throat speeds to keep the pressure safely above that level.
Why are Venturi meters shaped with a long exit cone?
A gentle, gradually widening exit lets the fast fluid slow down smoothly and recover most of its pressure. A sudden widening would make the flow separate from the walls and churn into eddies, wasting energy as heat. The long cone keeps the overall pressure loss small, which saves pumping energy in pipes that run all day.








