Fluid dynamics · efflux speed

Torricelli's Law

Torricelli's law states that liquid streams out of a small hole in an open tank at the same speed it would reach by falling freely from the liquid surface down to the hole, so v = √(2gh). Only the depth of the hole below the surface matters, not the shape of the tank or the type of liquid.

Clear water container with holes at three heights, each shooting a curved stream of water onto a lawn
Holes deeper below the surface shoot faster jets, just as Torricelli's law predicts.

At a Glance

Torricelli's law gives the speed of liquid leaving a small opening in an open tank: v = sqrt(2 g h), where h is the height of the liquid surface above the opening and g is the acceleration due to gravity. It is the same speed an object would have after falling a height h, and it follows from Bernoulli's equation and conservation of energy.

Discovered by
Evangelista Torricelli
When
1643, in an early form without modern notation
Formula
v = √(2gh)
SI unit of the result
meter per second (m/s)
Depends on
Depth of the hole below the surface and gravity, not on density
Applies to
A small opening in a wide open tank, with little viscosity and both surfaces at air pressure
On this page
  1. What Does Torricelli's Law Say?
  2. Torricelli's Law Explained Simply
  3. What Is the Formula for Torricelli's Law?
  4. How Do You Derive Torricelli's Law From Bernoulli's Equation?
  5. Why Is the Jet as Fast as a Falling Object?
  6. How Far Does the Water Jet Travel?
  7. Why Do Real Holes Flow Less Than the Formula Predicts?
  8. How Long Does It Take a Tank to Drain?
  9. Where Do You See Torricelli's Law in Everyday Life?
  10. When Does Torricelli's Law Not Apply?
  11. Who Discovered Torricelli's Law?
  12. Where Can You Practice Torricelli's Law Problems?
  13. Common Misconceptions
  14. Key Facts
  15. Quiz
  16. FAQ

What Does Torricelli's Law Say?

Torricelli's law describes how fast a liquid escapes through a small opening below its surface. Picture a tall bucket with a nail hole punched in its side. Water squirts out of the hole, and the law says the speed of that jet equals the speed a pebble would have if you dropped it from the water surface down to the level of the hole.

In symbols, the escape speed is v=2gh, where h is the vertical distance from the free surface down to the opening. The deeper the hole sits below the surface, the faster the stream. Four times the depth gives twice the speed, because the depth sits under a square root.

One surprise is what the law leaves out. Water, cooking oil and mercury all leave the same hole at the same speed if their surfaces stand at the same height. Density cancels, just as mass cancels when objects fall freely in a vacuum.

Torricelli's Law Explained Simply

Think of the liquid near the top of the tank slowly sliding down toward the hole. As it moves down, it gives up height, and that lost height turns into speed. By the time it reaches the opening, it is moving as fast as anything that has fallen the same distance.

That is why a hole near the bottom of a full tank gives a strong, fast jet, while a hole just below the surface gives a weak dribble. It is also why the jet slows down as the tank empties: the surface drops, the distance to the hole shrinks and there is less height left to turn into speed.

What Is the Formula for Torricelli's Law?

The law is written v=2gh. Here v is the speed of the liquid as it leaves the opening in meters per second, g is the acceleration due to gravity, about 9.81 m/s² near Earth's surface, and h is the height of the liquid surface above the opening in meters.

Three conditions sit behind the formula. The tank must be wide compared with the hole, so the surface sinks so slowly that its own speed is nearly zero. The liquid surface and the jet must both be open to the same air pressure. And the liquid should flow smoothly, without much viscous drag inside the opening.

If you know the speed and want the depth, square both sides to get h=v2/(2g). Our fluid formulas sheet lists this law next to the other flow equations it is usually combined with.

Here is Torricelli's law with each variable and its SI unit, plus the form solved for the height of the liquid above the hole.

v=2gh
What each symbol means
SymbolQuantitySI unit
vspeed of fluid leaving the openingmeter per second (m/s)
gacceleration due to gravity (9.80 m/s² (standard 9.80665 m/s²))meter per second squared (m/s²)
hheight of the fluid surface above the openingmeter (m)

Rearranged to find another variable:

h=v22g

Valid for: large open tank (surface speed ≈ 0), both surfaces at atmospheric pressure, no viscosity.

Example 1 A leak near the bottom of a water tower tank

A large open water tank has a small crack 3.2 m below its water surface. Ignoring friction in the opening and taking g = 9.81 m/s², how fast does water spurt out of the crack?

  1. Given:
    • acceleration due to gravity: g=9.81 m/s2
    • height of the fluid surface above the opening: h=3.2 m
  2. Formula: v=2gh
  3. Substitute: g=9.81 m/s2,h=3.2 m
  4. Answer: v=7.924 m/s (28.53 km/h, 17.72 mph)

A stone dropped from 3.2 m would hit the ground at exactly this speed, which is the whole idea of the law.

Ideal jet speed for different depths of liquid above the opening
Depth above hole h (m)Jet speed v (m/s)Jet speed (mph)Compared with h = 0.25 m
0.101.403.10.63×
0.252.215.01×
0.503.137.01.41×
1.04.439.92×
2.06.2614.02.83×
5.09.9022.24.47×
1014.0131.36.32×
Source: Computed with v = √(2gh), g = 9.81 m/s²; ideal values with no friction in the opening · Retrieved October 2026

How Do You Derive Torricelli's Law From Bernoulli's Equation?

The quickest route uses Bernoulli's principle, which says that pressure plus kinetic energy per volume plus potential energy per volume stays constant along a streamline: P+12ρv2+ρgy=constant.

Choose point 1 on the free surface and point 2 just outside the hole. Both are open to the air, so the pressures match and cancel. The surface barely moves, so its speed term is close to zero. What remains is ρgh=12ρv2, where h is the height difference. Divide by the density and solve, and you get v=2gh.

Notice that the density appeared on both sides and dropped out. That is the mathematical reason oil and water leave a hole at the same speed. The derivation is really conservation of energy applied to a small parcel of liquid.

Why Is the Jet as Fast as a Falling Object?

A rock dropped from rest through a height h lands at v=2gh, the same expression you meet in free fall. Torricelli's law has the identical form because the same energy swap is happening. Gravitational potential energy mgh becomes kinetic energy 12mv2, and mass cancels.

The liquid does not literally fall through the tank, of course. It is pushed toward the opening by the pressure of the liquid above it. But that pressure exists only because of the weight of the column, so the bookkeeping comes out the same. The energy bars below follow one kilogram of water from the surface to the hole.

The comparison also gives a neat check. Point a jet straight up through a short nozzle and, in an ideal world, it would climb back to the level of the free surface. Real fountains fall a little short because of friction and air drag.

Example 2 How deep is the hole below the surface?

A garden rain barrel has a small spout near its base. A student films the stream and finds it leaves the spout at 3.6 m/s. Taking g = 9.81 m/s², how far below the water surface is the spout?

  1. Given:
    • speed of fluid leaving the opening: v=3.6 m/s
    • acceleration due to gravity: g=9.81 m/s2
  2. Formula: h=v22g
  3. Substitute: v=3.6 m/s,g=9.81 m/s2
  4. Answer: h=0.6606 m

Working backward from speed to depth always squares the speed, so a small error in measuring v doubles as a percentage error in h.

Energy bars for 1 kg of water: 17.66 J of potential energy at the surface becomes 17.66 J of kinetic energy at the hole
The height the water gives up turns into speed at the hole.

How Far Does the Water Jet Travel?

Once the liquid leaves a hole in the side of a tank, it moves horizontally at first and then curves down like any thrown object. The jet is a horizontal projectile: its sideways speed stays constant while gravity pulls it down.

Suppose a tank stands on the ground with its surface 2.0 m up and a hole 0.8 m above the floor. The water is 1.2 m deep above the hole, so the jet leaves at about 4.85 m/s (computed) and lands roughly 1.96 m from the tank (computed). The diagram traces that path.

A classic puzzle asks which hole sends water the farthest. For a tank standing on the floor, the hole halfway up the water column wins. A hole near the top has plenty of fall time but little speed, while a hole near the bottom has speed but almost no time to travel before it hits the ground.

Parabolic path of a water jet leaving a tank hole 0.8 m above the floor at about 4.85 m/s
Exit speed from Torricelli's law, path from projectile motion: the jet lands about 1.96 m from the tank (computed).

Why Do Real Holes Flow Less Than the Formula Predicts?

Torricelli's law gives the ideal speed. Real openings deliver less liquid for two reasons. Friction at the edges slows the flow slightly, and with a sharp-edged hole the stream keeps narrowing for a short distance after it leaves, a pinch called the vena contracta.

Engineers handle both effects with a single discharge coefficient, Cd, and write the flow rate as Q=CdA2gh, where A is the area of the hole. A sharp-edged hole in a thin wall typically has Cd of about 0.6, while a smooth, rounded nozzle can come close to 1. The flow rate itself is the continuity equation idea of area times speed.

Very thick liquids such as honey break the law more seriously, because viscosity soaks up much of the energy. For slow flow through long, narrow tubes, Poiseuille's law is the better tool.

Example 3 How much water flows out each second?

A drum of water has a round hole of area 0.0002 m² (2 cm²) located 0.9 m below the surface. The hole has sharp edges, so the stream narrows and the effective discharge coefficient is about 0.62. Using g = 9.81 m/s², what volume of water leaves each second?

  1. Given:
    • discharge coefficient: Cd=0.62
    • area of the hole: A=2×10−4 m2
    • acceleration due to gravity: g=9.81 m/s2
    • height of the fluid surface above the opening: h=0.9 m
  2. Formula: Q=CdA2gh
  3. Substitute: Cd=0.62,A=2×10−4 m2,g=9.81 m/s2,h=0.9 m
  4. Answer: Q=5.211×10−4 m3/s

That is roughly half a liter every second. Without the 0.62 correction the ideal law would overestimate the flow by about 60 percent.

How Long Does It Take a Tank to Drain?

As a tank empties, h falls, so the jet slows and the flow rate drops. The tank does not drain at a steady pace. It loses water quickly at first and then more and more slowly as the level approaches the hole.

For a straight-sided tank, the water level falls in a pattern where the square root of the depth decreases steadily with time. A useful consequence is that the bottom quarter of the depth takes just as long to drain as the top three quarters. Anyone who has waited for a bathtub to finish emptying has seen a version of this effect.

Ancient water clocks ran into exactly this problem. A simple vessel with a hole in the bottom does not keep even time, so clock makers shaped their vessels to widen toward the top, which makes the level fall more steadily.

Where Do You See Torricelli's Law in Everyday Life?

  • Water towers and tanks. The higher the water stands above a tap, the faster water can leave it, which is why towers are tall.
  • Leaking containers. A pinhole near the bottom of a full jug sprays harder than the same pinhole near the top.
  • Dams and spillways. Outlets deep below a reservoir's surface release very fast streams, and engineers design the concrete below them to resist the scouring.
  • Rain barrels and coolers. The spout flows briskly when the container is full and slows to a trickle as it empties.
  • Sinks and bathtubs. A full tub drains fastest at the start, then slower as the depth falls.

Each case ties the jet speed to depth, the same link behind why pressure increases with depth.

Rain barrel spout near the base pouring a steady stream of water into a watering can in a garden
A rain barrel spout flows briskly when the barrel is full and slows as the water level drops.

When Does Torricelli's Law Not Apply?

The law is an idealization, and it fails when its conditions are not met. If the hole is large compared with the tank, the surface moves noticeably and the simple formula overestimates the speed. If the tank is sealed or pressurized, the pressure difference must be added, since a gauge pressure above the liquid pushes the jet faster than gravity alone.

The law also assumes steady flow. Right after a hole is opened, the liquid needs a brief moment to get moving. Very thick liquids, very small holes and flows that become turbulent all fall short of the ideal speed by more than a simple coefficient can fix.

Who Discovered Torricelli's Law?

The law is named after Evangelista Torricelli, the Italian mathematician and student of Galileo's ideas who is also known for the mercury barometer experiment. Around 1643 he reasoned that water leaving an opening should behave like a falling body, so the speed depends on the drop from the surface.

He did not have Bernoulli's equation, which came almost a century later. Daniel Bernoulli's work in the 1730s placed Torricelli's result inside a broader energy principle for moving fluids, and that is the way it is usually derived today.

Where Can You Practice Torricelli's Law Problems?

Most problems combine this law with projectile motion or with the continuity equation. Try our pressure worksheets for printable practice on depth and pressure, and use the projectile motion calculator to find where a jet lands once you know its exit speed. Then test yourself with the quiz below.

Common Misconceptions

Myth: Heavier liquids such as mercury squirt out faster than water.

Physics: Density cancels in the derivation. At the same depth, every non-viscous liquid leaves the hole at the same speed.

Myth: A tank empties at a steady rate.

Physics: The jet slows as the level drops, so the flow rate falls over time and the last part of the tank drains slowly.

Myth: The width of the tank changes the jet speed.

Physics: For a wide tank and a small hole, only the depth below the surface matters. Tank width affects how fast the level falls, not the jet speed.

Myth: A hole near the bottom always sends water the farthest.

Physics: The bottom hole gives the fastest jet, but for a tank on the floor the hole halfway down the water column usually reaches farthest because the jet has more time to travel.

Key Facts

  • Torricelli's law says liquid leaves a hole in an open tank at v = √(2gh), where h is the depth of the hole below the surface.
  • The jet speed equals the speed of an object that falls freely through the same height.
  • The density of the liquid cancels out, so water and oil leave the same hole at the same speed.
  • Four times the depth gives twice the jet speed, because the depth is under a square root.
  • The law follows from Bernoulli's equation and is really conservation of energy for a moving fluid.
  • Real sharp-edged holes deliver about 60 percent of the ideal flow, which engineers capture with a discharge coefficient.
  • Evangelista Torricelli described the result in 1643, nearly a century before Bernoulli's equation.
Did you know? Because the jet speed depends on the square root of the depth, a straight-sided tank takes as long to drain its last quarter of depth as it takes to drain the first three quarters.

Quick Quiz: How Well Do You Know Torricelli's Law?

6 questions. Tap an answer to check it.

  1. According to Torricelli's law, what happens to the jet speed if the depth of the hole below the surface is multiplied by four?

  2. Which quantity does NOT affect the ideal jet speed in Torricelli's law?

  3. Torricelli's law is a special case of which principle?

  4. Water leaves a hole 0.8 m below the surface. Ideally, its speed equals that of an object that has fallen how far?

  5. Why does a real sharp-edged hole deliver less flow than the ideal formula predicts?

  6. Who first described the law around 1643?

Frequently Asked Questions

What is Torricelli's law in simple terms?

Torricelli's law says that water flowing out of a small hole in an open tank moves as fast as a stone would after falling from the water surface down to the hole. The deeper the hole is below the surface, the faster the stream. The formula is v = √(2gh), where h is that depth and g is gravity.

What is the formula for Torricelli's law?

The formula is v = √(2gh). Here v is the speed of the liquid leaving the opening in meters per second, g is the acceleration due to gravity, about 9.81 m/s² on Earth, and h is the height of the liquid surface above the opening in meters. Rearranged, the depth is h = v²/(2g).

How is Torricelli's law derived?

Apply Bernoulli's equation between the liquid surface and the hole. Both points are open to the air, so the pressure terms cancel, and the surface moves so slowly that its speed is nearly zero. The remaining terms say ρgh = ½ρv². Cancel the density and solve for v to get v = √(2gh).

Does Torricelli's law depend on the density of the liquid?

No. Density appears on both sides of the energy balance and cancels out. In an ideal situation water, alcohol and mercury all leave the same hole at the same speed if their surfaces stand at the same height. In practice thick liquids flow slower, but that is due to viscosity, not density.

Is Torricelli's law a special case of Bernoulli's principle?

Yes. Torricelli found the result first, around 1643, by comparing the flow to free fall. Bernoulli's equation, developed about a century later, contains it as the special case of a wide open tank with a small opening, where pressures match and the surface speed is nearly zero.

Why does a tank drain more slowly as it empties?

The jet speed depends on the depth of liquid above the hole. As the tank drains, that depth shrinks, so the jet slows and less liquid leaves each second. For a tank with straight sides, the square root of the depth falls at a steady rate, so the final part of the tank takes a surprisingly long time.

What is the discharge coefficient in Torricelli's law?

It is a correction factor, written C_d, that accounts for friction and for the narrowing of the jet just after it leaves a sharp hole. The real flow rate is Q = C_d A √(2gh). A sharp-edged opening in a thin wall has a coefficient of about 0.6, while a smooth rounded nozzle can approach 1.

Does Torricelli's law work for a sealed or pressurized tank?

Not in its basic form. The law assumes the liquid surface and the jet are both at the same air pressure. If the space above the liquid is pressurized, the extra pressure pushes the liquid out faster, and you must include it using the full Bernoulli equation. A sealed tank with no air inlet may even stop flowing.

Physics Tribune Editorial Team
Written by our editors and checked against NIST and BIPM reference data. Every worked example is recomputed in code. Read our editorial policy. Last updated October 2026.